2026-08-09

挡泥板总成 - 前 - 左侧（拆卸和安装）

校正代码 10103001 0.96 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and its associated FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See 人员保护 to make sure wearing proper PPE when performing the below procedure. NOTE: See for safe and healthy working practices.

  • 2026-03-11: Updated photo and location description of rear fender bolt.
This procedure assumes the cowl screen carrier bracket, headlight grommet, and underhood storage unit clips on the fender assembly being replaced are undamaged. Inspect these components and if necessary, replace with new parts.

Torque Specifications

Table 1. 扭矩规格：
描述 扭矩值 推荐工具 重复使用/更换 备注
将前保险杠饰板顶部固定到车辆的螺栓
4 Nm (2.9 lbs-ft)
  • 10 毫米套筒扳手
 重复使用
将左侧前轮拱内衬固定到高压电池的螺栓
5 Nm (3.7 lbs-ft)
  • 10 毫米套筒扳手
 重复使用
将前保险杠饰板左侧角固定到翼子板的螺栓
4 Nm (2.9 lbs-ft)
  • 10 毫米套筒扳手
 重复使用
将前饰板右角固定到翼子板的螺栓
4 Nm (2.9 lbs-ft)
  • 10 毫米套筒扳手
 重复使用
将左侧前翼子板上方支架固定到车身的螺栓
9.8 Nm (7.2 lbs-ft)
  • 10 毫米深套筒
 重复使用
将左侧前翼子板支架固定到车身的螺栓
9.8 Nm (7.2 lbs-ft)
  • 10 毫米深套筒
 重复使用
将左侧前翼子板后部支架固定到车身的螺栓
9.8 Nm (7.2 lbs-ft)
  • 10 毫米深套筒
 重复使用
将左侧前翼子板下方支架固定到车身的螺母
9.8 Nm (7.2 lbs-ft)
  • 10 毫米深套筒
 重复使用

拆卸

  1. Raise and support the vehicle. See .
  2. Open all doors and fully lower all windows.
  3. Remove the rear underhood apron. See 前备箱挡板 - 后部（拆卸和更换）.
  4. Remove the underhood storage unit. See 前备箱储物单元（拆卸和更换）.
  5. Remove the bolts that attach the top of the front fascia to the vehicle.
    4 Nm (2.9 lbs-ft)
    Tip
    推荐使用以下工具
    • 10 毫米套筒扳手
  6. Remove the front wheels. See .
  7. Remove the front aero shield panel. See 面板 - 流线型护板 - 前（非结构化电池组）（拆卸和更换）.
  8. Remove the LH front wheel liner. See 轮拱内衬 - 前 - LH（非结构化电池组）（拆卸和更换）.
  9. Remove the bolt that attaches the LH corner of the front fascia to the fender.
    4 Nm (2.9 lbs-ft)
    Tip
    推荐使用以下工具
    • 10 毫米套筒扳手
    Figure 1. LH shown; RH similar
  10. Remove the RH front fender garnish. See .
  11. Remove the clips (x6) that attach the front of the RH front wheel liner to the vehicle.
  12. Remove the bolt that attaches the RH corner of the front fascia to the fender.
    4 Nm (2.9 lbs-ft)
    Tip
    推荐使用以下工具
    • 10 毫米套筒扳手
    Figure 2. LH shown; RH similar
  13. Disconnect the electrical connector from the front fascia in the RH wheel well.
  14. If present, release the clip that attaches the electrical harness to the pedestrian warning speaker assembly.
  15. If present, slide the locking tab away from the connector, and then press down on the locking tab to disconnect the connector from the pedestrian warning speaker assembly.
  16. With an assistant, release the LH side of the front fascia, and then carefully pull the fascia up and forward to remove it from the vehicle. Place the fascia on a padded surface.
    CAUTION
    Carefully release the tabs that attach the lower headlight bracket to the front fascia, otherwise the tabs can be broken.
    Warning
    The corners of the ankle catcher are very sharp and might cause personal injury.

    LH ankle catcher corner shown; RH corner similar

  17. Remove the LH headlight. See .
  18. Remove the LH side repeater light. See .
  19. Remove the LH fascia side to fender bracket. See .
  20. Release the clip that attaches the cowl screen to the LH side of the carrier bracket.
  21. Remove the bolts that attach the upper LH front fender bracket to the body.
    9.8 Nm (7.2 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • 10 毫米深套筒
  22. Remove the bolt that attaches the LH front fender bracket to the body.
    9.8 Nm (7.2 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • 10 毫米深套筒
  23. Remove the bolt that attaches the rear LH front fender bracket to the body.
    9.8 Nm (7.2 lbs-ft)
    Note
    The bolt is located outside the upper fender near the door hinge.
    Tip
    Use of the following tool(s) is recommended:
    • 10 毫米深套筒
  24. Remove the nuts that attach the lower LH front fender bracket to the body.
    9.8 Nm (7.2 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • 10 毫米深套筒
  25. Remove the LH front fender assembly from the vehicle

安装

Tip
For instructions on how to align the fender, refer to .
  1. Install the front underhood storage fender clips onto the LH front fender.
  2. Position the LH front fender assembly onto the vehicle
  3. Install the nuts that attach the lower LH front fender bracket to the body.
    9.8 Nm (7.2 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • 10 毫米深套筒
  4. Install the bolt that attaches the rear LH front fender bracket to the body.
    9.8 Nm (7.2 lbs-ft)
    Note
    The bolt is located inside upper fender.
    Tip
    Use of the following tool(s) is recommended:
    • 10 毫米深套筒
  5. Install the bolt that attaches the LH front fender bracket to the body.
    9.8 Nm (7.2 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • 10 毫米深套筒
  6. Install the bolts that attach the upper LH front fender bracket to the body.
    9.8 Nm (7.2 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • 10 毫米深套筒
  7. Install the clip that attaches the cowl screen to the LH side of the carrier bracket.
  8. Install the LH fascia side to fender bracket. See .
  9. Install the LH side repeater light. See .
  10. Install the LH headlight from the vehicle. See .
  11. With an assistant, position the front fascia onto the vehicle. and then fasten the clips (x8).
  12. If present, install the clip that attaches the electrical harness to the pedestrian warning speaker assembly.
  13. If present, connect the pedestrian warning speaker electrical connector, and then engage the connector lock.
  14. Connect the electrical connector for the front fascia in the RH wheel well.
  15. Install the bolt that attaches the RH corner of the front fascia to the fender.
    4 Nm (2.9 lbs-ft)
    Tip
    推荐使用以下工具
    • 10 毫米套筒扳手
    Figure 3. LH shown; RH similar
  16. Install the clips (x6) that attach the front of the RH front wheel liner to the vehicle.
  17. Install the RH front fender garnish. See .
  18. Install the bolt that attaches the LH corner of the front fascia to the fender.
    4 Nm (2.9 lbs-ft)
    Tip
    推荐使用以下工具
    • 10 毫米套筒扳手
    Figure 4. LH shown; RH similar
  19. Install the LH front wheel liner. See 轮拱内衬 - 前 - LH（非结构化电池组）（拆卸和更换）.
  20. Install the LH front fender garnish. See .
  21. Install the front aero shield panel. See 面板 - 流线型护板 - 前（非结构化电池组）（拆卸和更换）.
  22. Install the front wheels. See .
  23. Install the bolts that attach the top of the front fascia to the vehicle.
    4 Nm (2.9 lbs-ft)
    Tip
    推荐使用以下工具
    • 10 毫米套筒扳手
  24. Install the underhood storage unit. See 前备箱储物单元（拆卸和更换）.
  25. Install the rear underhood apron. See 前备箱挡板 - 后部（拆卸和更换）.
  26. Open all doors and fully lower all windows.
  27. Remove the vehicle from the lift.