2025-12-04

Headliner - Front (Model YL) (Remove and Replace)

Correction code 15200200101 FRT 1.32 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

Torque Specifications

Table 1. Torque Specifications: Headliner - Front (Model YL) (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts that attach the rear coat hooks to the headliner
2.5 Nm (1.8 lbs-ft)
  • Torx T25 socket
 Reuse
Bolts that attach the headliner to the body
2 Nm (1.5 lbs-ft)
  • Torx T30 socket
 Reuse

Remove

  1. Remove the LH front primary body seal. See Primary Body Seal - Front - LH (Remove and Replace).
  2. Remove the LH upper A-pillar trim. See Trim - A-Pillar - Upper - LH (Remove and Replace).
  3. Remove the LH sun visor. See Sun Visor - LH (Remove and Replace).
  4. Repeat step 1 through step 3 on the RH side of the vehicle.
  5. Remove the LH rear primary body seal. See Primary Body Seal - Rear - LH (Remove and Replace).
  6. Remove the LH B-pillar lower trim. See Trim - B-Pillar - Lower - LH (Model YL) (Remove and Replace).
  7. Release the clip that attaches the LH B-pillar lower air duct to the body.
  8. Release the clips (x5) that attach the LH B-pillar upper trim assembly to the vehicle, and then move the trim aside.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull the bottom of the upper B-pillar inwards, and then pull the top to release the remaining clips.
  9. Repeat step 5 and step 8 on the RH side of the vehicle.
  10. Move the 2nd row seats forward.
    Informational PurposesAn informational icon, calling your attention
    Note
    Adjust the seat back if needed.
  11. Open the liftgate.
  12. Fold the 3rd and 2nd row seatbacks down.
    Informational PurposesAn informational icon, calling your attention
    Note
    Protect the seat back upholstery from any potential scratch or damage.
  13. Release the clips (x14), locator pins (x2), and tabs (x2) that attach the LH trunk side trim to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    This is to aid the removal of the C-pillar upper trim.
  14. Release the clips (x10), locator pins (x4), and tabs (x2) that attach the LH C-pillar upper trim to the body, and then disconnect the seat dump switch connector and release the charging port release cable.
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not pull the trim too far from the vehicle, as it is still attached by the connector and charging port release cable.
  15. Release the clips (x14), locator pins (x2), and tabs (x2) that attach the RH trunk side trim to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    This is to aid the removal of the C-pillar upper trim.
  16. Release the clips (x10), locator pins (x4), and tabs (x3) that attach the RH C-pillar upper trim to the body.
  17. Remove the rear headliner. See Rear Headliner (Model YL) (Remove and Replace).
  18. Push to open the LH rear coat hook.
  19. Release the tab to open the LH rear coat hook bolt cover.
  20. Remove the bolt that attaches the LH rear coat hook to the headliner.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T25 socket
  21. Release the tab to partially release the headliner from the body, and then remove the bolt that attaches the headliner to the body.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T30 socket
  22. Repeat step 18 through step 21 on the RH side of the vehicle.
  23. Tilt both front seats rearward to allow headliner removal.
  24. Release the clips (x7) that attach the front headliner harness to the LH A-pillar, and then disconnect the front connector.
  25. Release the clip that attaches the front headliner harness to the RH C-pillar, and then disconnect the rear connector.
  26. Release the clips, tabs, magnets and tether that attach the front headliner to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    There are tethers on both sides of the rear section of the front headliner. Depress the tabs (x2) of the tether to release it.
  27. With assistance, slightly bend the front headliner and tilt it to remove it from the vehicle.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Take care not to damage the front headliner.

Install

  1. With assistance, slightly bend the front headliner and tilt it to install it onto the vehicle.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Take care not to damage the front headliner.
  2. With assistance, install the clips, tabs, magnets and tether that attach the front headliner to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    Ensure that the seal covers the interior trim panel.
  3. Connect the front connector, and then install the clips (x7) that attach the front headliner harness to the LH A-pillar.
  4. Connect the rear connector, and then install the clip that attaches the front headliner harness to the RH C-pillar.
  5. Install the bolt that attaches the headliner to the body, and then install the tab that attaches the headliner to the body.
    2 Nm (1.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T30 socket
  6. Install the bolt that attaches the LH rear coat hook to the headliner.
    2.5 Nm (1.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T25 socket
  7. Engage the tab to close the LH rear coat hook bolt cover.
  8. Push to close the LH rear coat hook.
  9. Repeat step 5 through step 8 on the RH side of the vehicle.
  10. Install the rear headliner. See Rear Headliner (Model YL) (Remove and Replace).
  11. Install the clips (x10), locator pins (x4), and tabs (x3) that attach the RH C-pillar upper trim to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    While installing the upper trim, make sure that the air vent is properly installed.
    Informational PurposesAn informational icon, calling your attention
    Note
    After installation, make sure that the seal fully covers the edge of the trim.
  12. Install the clips (x14), locator pins (x2), and tabs (x2) that attach the RH trunk side trim to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    After installation, make sure that the seal fully covers the edge of the trim.
  13. Connect the seat dump switch connector and install the charging port release cable, and then install the clips, locator pins, and tabs that attach the LH C-pillar upper trim to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    While installing the upper trim, make sure that the air vent is properly installed.
    Informational PurposesAn informational icon, calling your attention
    Note
    After installation, make sure that the seal fully covers the edge of the trim.
  14. Install the clips (x14), locator pins (x2), and tabs (x2) that attach the LH trunk side trim to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    After installation, make sure that the seal fully covers the edge of the trim.
  15. Move the 1st row seats back to their original positions.
  16. Move the 3rd and 2nd row seatbacks back to its original position.
  17. Move the 2nd row seats back to their original positions.
  18. Close the liftgate.
  19. Align location pins (x2) to the slots on the body, and then secure the clips (x5) that attach the LH upper B-pillar trim assembly to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Lower the seat belt slider to align it with the B-pillar panel.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure that the air vent is properly installed.
  20. Install the clip that attaches the LH B-pillar lower air duct to the body.
  21. Install the LH B-pillar lower trim. See Trim - B-Pillar - Lower - LH (Model YL) (Remove and Replace).
  22. Install the LH rear primary body seal. See Primary Body Seal - Rear - LH (Remove and Replace).
  23. Repeat step 19 through step 22 on the RH side of the vehicle.
  24. Install the LH sun visor. See Sun Visor - LH (Remove and Replace).
  25. Install the LH upper A-pillar trim. See Trim - A-Pillar - Upper - LH (Remove and Replace).
  26. Install the LH front primary body seal. See Primary Body Seal - Front - LH (Remove and Replace).
  27. Repeat step 24 through step 26 on the RH side of the vehicle.
  28. Raise all four windows and close all four doors.