2026-08-05

Valance - Front Fascia (Remove and Replace)

교정 코드 1203010052 FRT 0.30 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 의 내용을 참조하십시오.

  • 2026-07-31: Added steps for the super horn cover clip.
  • 2026-03-16: Added notes and tools for bolts securing front valance to front fascia on newer vehicles.
Informational PurposesAn informational icon, calling your attention
참고
The images in this repair procedure show a Non-Performance vehicle. The instructions apply to both the Non-Performance and the Performance version.

토크 규격

표 1. 토크 규격: Valance - Front Fascia (Remove and Replace)
설명 토크 값 권장 공구 재사용/교체 참고
Screws (x3) that attach the super horn to the valance
1.8 Nm (1.3 lbs-ft)
  • Torx T25 소켓
 재사용
Bolts (x8) that attach the valance to the fascia
3 Nm (2.2 lbs-ft)
  • Torx T40 소켓
  • (If equipped) 10mm 소켓
 재사용
Nuts (x2) at the LH and RH corners of the valance
3 Nm (2.2 lbs-ft)
  • 10mm 소켓
 재사용

탈거

  1. Remove the front aero shield panel. See Panel - Aero Shield - Front (Remove and Replace).
  2. Remove the push clips (x6) that attach the LH and RH sides of the valance to the wheel arch liners.
    Informational PurposesAn informational icon, calling your attention
    Note
    Remove the outer clips as necessary to allow for easier access to the nuts behind the wheel liner.
  3. Remove the clip that attaches the super horn cover to the front fascia.
  4. Remove the nuts (x2) at the LH and RH corners of the valance.
    Informational PurposesAn informational icon, calling your attention
    Note
    The nuts are accessed from behind the front of the wheel arch liners.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구를 사용하는 것이 좋습니다.
    • 10mm 소켓
  5. Release the clip that attaches the super horn harness to the super horn, and then disconnect the super horn connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    커넥터 접근 방식은 차량에 장착된 슈퍼혼 오디오 스피커 버전에 따라 다를 수 있습니다.
  6. Remove the bolts (x8) that attach the valance to the front fascia, and then remove the valance from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Newer vehicles are equipped with 6 T40 bolts and 2 10mm bolts.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구를 사용하는 것이 좋습니다.
    • Torx T40 소켓
    • (If equipped) 10mm 소켓
  7. Remove the screws (x3) that attach the super horn to the valance, and then remove the super horn from the valance.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구를 사용하는 것이 좋습니다.
    • Torx T25 소켓

장착

  1. Install the super horn to the valance, and then install the screws (x3) that attach the super horn to the valance.
    1.8 Nm (1.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구를 사용하는 것이 좋습니다.
    • Torx T25 소켓
  2. Install the valance to the front fascia, and install the bolts (x8) that attach the valance to the fascia.
    3 Nm (2.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Newer vehicles are equipped with 6 T40 bolts and 2 10mm bolts.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구를 사용하는 것이 좋습니다.
    • Torx T40 소켓
    • (If equipped) 10mm 소켓
  3. Connect the super horn connector, and then install the clip that attaches the super horn harness to the super horn.
  4. Install the nuts (x2) at the LH and RH corners of the valance.
    3 Nm (2.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    The nuts are accessed from behind the front of the wheel liners.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구를 사용하는 것이 좋습니다.
    • 10mm 소켓
  5. Install the clip that attaches the super horn cover to the front fascia.
  6. Install the push clips (x6) that attach the LH and RH sides of the valance to the wheel liners.
  7. Install the front aero shield panel. See Panel - Aero Shield - Front (Remove and Replace).