2026-05-13

Compressor (Remove and Replace)

교정 코드 18203912 1.02 메모: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오. 메모: 안전하고 건강한 작업 사례는 의 내용을 참조하십시오.

  • 2026-01-05: Revised procedure to flush the system and eliminate oil weighing and correction steps.
  • 2025-11-04: Added reference information for compressor Type con fig.
  • 2025-07-18: Swapped steps for compressor con fig setting and firmware redeployment.
  • 2023-05-02: Added steps to remove/install NVH acoustic cover.
  • 2023-06-20: Added compressor weight including oil for San den type compressor.
  • 2024-01-30: Removed the A/C flush-related steps and updated the way of performing the routines from using Toolbox to using the touchscreen.
  • 2024-03-04: Updated the description of the oil amount calculation steps.
Special tools required for this procedure:
  • 1600279-00-A A/C OIL FLUSH ADAPTER SET, MODEL Y or 1600279-N0-BHEAT PUMP VEHICLE A/C FLUSHING FOR UNKNOWN OIL CONDITIONS
  • 1711245-00-A - Snap On Ecotechnics Dual Gas A/C Machine, includes Flush Adapter Kit R134A & R1234YF
  • 1120026-01-A A/C SERVICE MACHINE, WAECO, ASC5500 RPA
Informational PurposesAn informational icon, calling your attention
Note
Refer to Toolbox Article #5696900 for additional information regarding compressor replacement in Giga Shanghai manufactured vehicles.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning

모든 필수 인증 교육을 완료한 기술자만 이 절차를 수행할 수 있습니다. Tesla는 타사 서비스 제공업체 기술자가 이 절차를 수행하기 전에 동등한 교육을 받을 것을 권장합니다. Tesla 기술자 요구 사항에 대한 자세한 내용이나 타사 기술자에 대한 분야별 설명은 HV Certification Requirements를 참조하십시오. 고전압 케이블, 버스바 또는 피팅을 다룰 때에는 항상 적합한 개인 보호 장비(PPE)와 클래스 0(1000V)의 최소 정격을 갖는 절연 HV 장갑을 착용해야 합니다. 추가 안전 정보는 기술 노트 TN-15-92-003고압 인식 주의 사항을 참조하십시오.

Warning IconA warning icon, calling your attention to a possibly risky situation
CAUTION
Model Y 열 관리 구성품은 매우 엄격한 규격에서 작동하며 정비 절차를 주의 깊게 따르지 않으면 오작동할 수 있습니다. 다른 열 관리 시스템에 대한 과거의 경험에 의존하지 마십시오. 정비 설명서를 읽고 지침에서 벗어나지 마십시오.
Informational PurposesAn informational icon, calling your attention
Note
This procedure requires the A/C Refrigerant (Recovery and Recharge) procedure to be performed. If not already automatically added to the Service Visit, add correction code 18200102 as a separate correction within the same activity to the Service Visit.

토크 규격

Table 1. 토크 규격: Compressor (Remove and Replace)
설명 토크 값 권장 공구 재사용/교체 참고
저압 파이프를 A/C 컴프레서에 고정하는 너트
22 Nm (16.2 lbs-ft)
  • 13mm 딥소켓
 재사용
고압 파이프를 A/C 컴프레서에 고정하는 너트
22 Nm (16.2 lbs-ft)
  • 13mm 딥소켓
 재사용

탈거

  1. Remove the HEPA filter assembly. See .
  2. Remove the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  3. Place the vehicle in Service Mode by using the touchscreen. See .
  4. Unlock the vehicle gateway. See .
  5. On the touchscreen, touch the Service Mode "wrench" icon, and then touch Thermal > Refrigerant System > Start Thermal Fill Drain (Refrigerant only) > Run, and allow the routine to complete.
  6. 차량 HV 비활성화 절차를 수행합니다. 참조 항목: Vehicle HV Disablement Procedure.
  7. Recover the A/C refrigerant. See .
    Informational PurposesAn informational icon, calling your attention
    Note
    Recover the refrigerant while continuing this procedure.
  8. Remove the LV battery. See .
  9. After refrigerant recovery is complete, carefully depress the Schrader valves (x2) to level out any pressure difference between the A/C system pressure and the actual ambient atmospheric pressure.
  10. Remove the desiccant, see
  11. Install a new cap into the accumulator, and then install a new snap ring into the accumulator.
  12. Remove the nut that attaches the low pressure fitting to the A/C compressor.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구를 사용하는 것이 좋습니다.
    • 13mm 딥소켓
  13. Remove the nut that attaches the high pressure fitting to the A/C compressor, and then set the hose assembly aside.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구를 사용하는 것이 좋습니다.
    • 13mm 딥소켓
  14. Install A/C flush adapters onto the A/C manifold to compressor line.
  15. Connect A/C machine hoses to A/C flush adapters.
  16. On the A/C machine touchscreen, select Menu > Flushing Kit, and enter 25 mins vacuum time. and then follow the machine guide to start the flush, and then allow the process to complete.
    Informational PurposesAn informational icon, calling your attention
    Note
    system flush procedure runs for approximately 90 minutes.
  17. Remove the compressor bracket. See .
  18. Note the part numbers and serial numbers of the old and new A/C compressors.

장착

Warning IconA warning icon, calling your attention to a possibly risky situation
CAUTION
The new A/C compressor is pre-filled with oil. DO NOT add any additional oil to the new A/C compressor.
  1. Install the NVH acoustic cover onto the new compressor.
  2. Install the new compressor with compressor bracket to the vehicle. See .
  3. Replace the O-rings on the high pressure and low pressure supermanifold to A/C compressor hose fittings.
    Informational PurposesAn informational icon, calling your attention
    Note
    O-ring for high pressure line: 1111737-00-A WASHER, 3/8,STL ZN, SEAL.
    Informational PurposesAn informational icon, calling your attention
    Note
    O-ring for low pressure line: 1111740-00-A WASHER, 3/4,STL ZN, SEAL.
    Informational PurposesAn informational icon, calling your attention
    Note
    Lubricate O-rings with ND-11 oil prior to installation.
    Figure 1. Low pressure fitting shown; high pressure fitting similar
  4. Remove the transport plugs from the new compressor.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13mm 소켓
  5. Position the supermanifold to A/C compressor high pressure fitting on the A/C compressor, and then install the nut that attaches the fitting to the A/C compressor.
    22 Nm (16.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구를 사용하는 것이 좋습니다.
    • 13mm 딥소켓
  6. Position the supermanifold to A/C compressor low pressure fitting on the A/C compressor, and then install the nut that attaches the fitting to the A/C compressor.
    22 Nm (16.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구를 사용하는 것이 좋습니다.
    • 13mm 딥소켓
  7. Install a new desiccant. See .
  8. Perform an A/C vacuum leak test and recharge the refrigerant. See .
  9. Install the LV battery. See .
  10. Reconnect LV power. See 12V/LV Power (Disconnect and Connect).
  11. Connect a LV maintainer. See .
  12. Enable Service Mode Plus. See .
  13. On the touchscreen, touch Controls > Thermal > Thermal Configurations > compressorType, and select and save the correct type.
    Informational PurposesAn informational icon, calling your attention
    Note
    Refer to Toolbox article 5696900 for details on compressor configuration.
    Informational PurposesAn informational icon, calling your attention
    Note
    Check the compressorType and make sure it shows as intended.
  14. Configure the compressor type: on the touchscreen, touch Thermal > Actions > Thermal Configurations, and then select the correct compressor type from the drop down list. Touch Run, and close once the routine has passed.
  15. Reinstall the software. See .
  16. On the touchscreen, touch Thermal > Refrigerant System > Reset Compressor P-Metric > Run, and close once the routine has passed.
  17. Tap Thermal > Sensors and Valves > Run Heat Pump Commissioning > Run, and close once the routine has passed.
  18. Tap Thermal > Actions > Test Thermal Performance > Run, and close once the routine has passed.
  19. Tap Thermal > Actions > Test HVAC Performance > Run, and close once the routine has passed.
  20. Exit Service Mode. See .
  21. Install the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  22. Install the HEPA assembly. See .
  23. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  24. Install the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).