2026-09-10

차량 HV 비활성화 절차

교정 코드 17010000 0.30 메모: 절차에서 명시적으로 언급하지 않는 한 교정 코드 및 해당 관련 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오. 메모: 안전하고 건강한 작업 사례는 의 내용을 참조하십시오.

  • 2026-09-10: Updated the procedure to use the amp clamp and voltage measurement method at the rear drive unit cables from underneath the vehicle.
  • 2025-11-26: Added note to keep HV gloves on if procedure that required disablement involves touching HV components.
  • 2025-10-22: Added info in measurement table on GND point to be used for Negative (-) Lead, modified measurement sequence.
  • 2025-03-24: Added warning for regional tooling regulations.
  • 2025-01-30: Clarified B+ and B- probe step.
  • 2024-10-21: Rearranged multimeter probing images to align with HV measurement table.
  • 2024-06-05: Added warning to measure the specified order of locations for high voltage.
  • 2023-12-12: Updated voltage measurement order.
  • 2023-12-05: Updated references to other Vehicle Isolation Procedures.
  • 2023-11-08: Added/updated HV insulating glove steps.
  • 2023-08-30: Added a tip about replacing the probe to the multimeter-related step.
Warning
This procedure verifies that high voltage power is no longer available to high voltage components (A/C compressor, inverters, etc). Perform this procedure before servicing high voltage components.
Warning
고전압에 노출되는 절차를 수행하기 전에 작업자에게 모든 장신구(시계, 팔찌, 반지, 목걸이, 귀걸이, ID 태그, 피어싱 장신구 등)를 벗으라고 하고 주머니에서 모든 물건(열쇠, 동전, 펜, 연필, 공구, 패스너 등)을 꺼내 놓으십시오.
Warning
절차를 수행하기 위해서 시력 교정 안경이 필요한 경우, 시력 교정 안경을 머리에 단단히 고정하여 떨어지지 않게 하십시오.
Warning
Always wear High Voltage (HV) gloves and safety glasses when handling any high voltage component, including test equipment. Before each use, test gloves using an authorized glove tester and verify that the testing date on the gloves has not expired.
Warning
All repair and operating instructions should be reviewed and understood before working on Tesla vehicles, associated components, or associated repair equipment.
Warning
Assume that high voltage is present at all times when working on a Tesla vehicle, associated high voltage components, or associated high voltage test equipment until proven otherwise. Be aware that energy states can change during testing, so err on the side of caution.
Warning
Always have an electrical safety hook in the area when working with HV components. Electrical safety hooks are used to remove an injured person from a live high voltage circuit without risking additional injury.
Warning
Use a high voltage digital multimeter to check for the presence of high voltage on both sides of the connector every time a high voltage connector is disconnected.
Warning
일부 지역에서는 이 절차를 위해 전압 부재 테스터(VAT)가 필요하며 멀티미터 사용은 허용되지 않습니다. 항상 현지 또는 지역별 공구 규정을 준수하십시오.
Warning
Make sure that the multimeter and leads are capable of handling at least 500V DC.
Warning
Obey all instructions when using test equipment or servicing a Tesla vehicle or associated high voltage components. If repair instructions are not clear or if there are any questions about how to use the test equipment, escalate a Toolbox session before proceeding.
Warning
If any test equipment fails to operate as expected, do not attempt to diagnose or repair the vehicle. Follow the appropriate lock out – tag out procedure for the equipment, notify your manager.
Warning
When using test equipment, make sure that all cables are connected before turning equipment on or otherwise initiating use.
Warning
High voltage is present on battery recovery chargers whenever the HV LEDs are lit. However, indicators and LEDs can fail. Do not assume that if an LED is not lit no high voltage is present. Assume high voltage is present at all times until proven otherwise by use of a multimeter.
Warning

모든 필수 인증 교육을 완료한 기술자만 이 절차를 수행할 수 있습니다. Tesla는 타사 서비스 제공업체 기술자가 이 절차를 수행하기 전에 동등한 교육을 받을 것을 권장합니다. Tesla 기술자 요구 사항에 대한 자세한 내용이나 타사 기술자에 대한 분야별 설명은 HV Certification Requirements를 참조하십시오. 고전압 케이블, 버스바 또는 피팅을 다룰 때에는 항상 적합한 개인 보호 장비(PPE)와 클래스 0(1000V)의 최소 정격을 갖는 절연 HV 장갑을 착용해야 합니다. 추가 안전 정보는 기술 노트 TN-15-92-003고압 인식 주의 사항을 참조하십시오.

Equipment:
  • 1083188-01-B - Digital Multimeter Unit, EXTECH 355
  • 1754057-00-A - CURRENT PROBE, GEN, CLAMP, DC, 600V
  • 1140311-00-A - LEVER LOCK, HV CONNECTOR, MODEL 3
  • 1115247-01-A - Electronic Test Lead, CAT IV 1000V
  • 1130480-02-B - Slim Test Probes, CAT III 1000V

Procedure

Note
This procedure is for 구조용 팩 이외 5 seat vehicles. For instructions on checking HV disablement on 구조용 팩 이외 7 seat vehicles, see 차량 HV 비활성화 절차(7인승). For instructions on checking HV disablement on 구조용 팩 5 seat vehicles, see 차량 HV 비활성화 절차 (구조용 팩).
  1. Disconnect 12V/LV power. See 12V/LV 전원(연결 해제 및 연결).
  2. Set the multimeter to measure voltage, and then measure the voltage across the 12V/LV auxiliary battery terminals.
    Note
    For LV (Li-Ion) auxiliary battery: if the voltage across the battery terminals is 0, the battery may have switched off internally. Use a 12V Lead Acid battery for testing. For mobile technicians: use the 12V Lead Acid battery in the Mobile Service vehicle.
    CAUTION
    For LV (Li-Ion) auxiliary battery: if the voltage across the battery terminals is less than 13 volts or greater than 16 volts, the multimeter is not measuring reliably and must not be used.
    CAUTION
    For 12V (Lead Acid) auxiliary battery: if the voltage measured is less than 10 volts or greater than 14 volts, the multimeter is not measuring reliably and must not be used.
  3. Remove the rear aero shield panel. See 패널 - 에어로 실드 - 후면(탈거 및 교체).
  4. Remove the rear skid plate. See .
  5. Install the current clamp meter onto one cable of the rear drive unit HV harness.
    Note
    Make sure the meter is zeroed out and is facing the correct direction as shown.
  6. Measure the current in the HV cable.
    • If the current is within the range of -0.5 A to 0.5 A, continue to the next step.
    • If the current is outside the range of -0.5 A to 0.5 A, for example -0.8 A or 1.3 A, re-perform the vehicle electrical isolation again to make sure that all was properly shut down. If the measurement is still outside the range of -0.5 A to 0.5 A, escalate for assistance.
    Warning
    DO NOT DISCONNECT any HV harness when the current measurement is outside the range of -0.5 A to 0.5 A.
  7. Remove the clamp meter from the cable.
  8. Remove the nut that attaches the rear drive unit HV cable bracket to the HV battery.
    Note
    The number of the fasteners may vary.
    Tip
    다음 공구를 사용하는 것이 좋습니다.
    • 10mm 소켓
  9. Remove all jewelry and empty your pockets before continuing this procedure.
  10. Inspect and put on HV insulating gloves, leather outer gloves, and safety glasses before continuing this procedure.
  11. Disconnect the connector that attaches the rear drive unit HV cable to the HV battery.
    Note
    Release the locking tab and rotate the release lever up to disengage the connector. Do not force the release lever up. Ensure the alignment tabs on the rear drive unit header are not damaged.
  12. Use the high voltage multimeter with CAT III probes to verify that no high voltage is present at the rear drive unit HV header.
    Warning
    잠재적 고전압 노출을 제한하기 위해 아래 지정된 순서에 따라 고전압을 측정하십시오.
    Measure the following voltages:
    1. B+ to ground
    2. B- to ground
    3. B+ to B-
    Warning
    If any voltage is greater than 10V, the contactors are closed or welded. Escalate to Service Engineering.
  13. Make sure the connector lock is 90 degrees from the connector, and then connect the connector that attaches the rear drive unit HV cable to the HV battery.
    Note
    Use one hand to support the connector while the other latching the locking tab. Once installed, verify that the latch is not damaged and is fully secured in the latched position.
  14. Remove the leather over gloves and the HV insulating gloves.
  15. Install the nut that attaches the rear drive unit HV cable bracket to the HV battery.
    Note
    The number of the fasteners may vary.
    Tip
    다음 공구를 사용하는 것이 좋습니다.
    • 10mm 소켓
  16. Install the rear skid plate. See .
  17. Install the rear aero shield panel. See 패널 - 에어로 실드 - 후면(탈거 및 교체).
  18. Connect 12V/LV power. See 12V/LV 전원(연결 해제 및 연결).
  19. Return to the procedure that required the vehicle to be electrically isolated.
    Warning
    차량을 전기 절연해야 하는 절차의 모든 안전 지침과 PPE 요구 사항을 따르십시오. 고전압 케이블, 버스바 또는 피팅을 다루는 절차의 경우 HV 장갑을 벗지 마십시오.
    Note
    If you are no longer exposed to high voltage, the HV insulating gloves may be removed.