2026-08-09

Dossier de siège - 2e rangée - gauche (retirez et remplacez)

Code de correction 13054002 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and its associated FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Protection individuelle to make sure wearing proper PPE when performing the below procedure. NOTE: See for safe and healthy working practices.

  • 2024-07-23: Deleted the seatback cushion separation steps.
  • 2024-08-15: Added a note for NA vehicles to remind that the seat covers without ISOFIX flag for child locks must be replaced.
Équipement :
  • Torchless Heat Induction Tool - 2152873-00-A

Spécifications de couple

Tableau 1. Spécifications de couple: Dossier de siège - 2e rangée - gauche (retirez et remplacez)
Description Valeur de couple Outils recommandés Réutiliser/remplacer Remarques
Boulons (x5) qui fixent le cadre du dossier du siège de la 2e rangée gauche au véhicule
37 Nm (27.3 lbs-ft)
  • Douille de 11mm
Remplacer
ATTENTION
Les boulons doivent être installés en respectant la séquence suivante :
  1. Extérieur avant
  2. Intérieur arrière
  3. Extérieur arrière
  4. Intérieur avant

Retirer

  1. Remove the LH lower C-pillar trim. See .
  2. Release the clips (x3) that attach the main carpet to the lower seat cushion frames.
  3. Remove the bolts (x5) that attach the LH 2nd row seat back frame to the vehicle.
    Remarque
    The two frontmost bolts are behind the main carpet.
    Conseil
    L'un ou plusieurs des outils suivants sont recommandés :
    • Douille de 11mm
  4. Carefully fold down the LH 2nd row seat back.
    ATTENTION
    Place a protective covering on the seat back upholstery and take care not to damage the upholstery during removal of the seat back.
    ATTENTION
    Do not place any additional weight on the seat back. Doing so may damage the seat frame alignment tabs, which can cause unevenness between the 60 and 40 seat backs.
  5. Disconnect the electrical harness from the connector at the LH lower seat frame.
  6. With assistance, carefully remove the LH 2nd row seat back assembly from the vehicle.
    ATTENTION
    Place the seat back assembly in an area where it will not be tipped over or otherwise damaged.
    Remarque
    For NA only: If the 2nd row seat that is not being replaced does not have ISOFIX flag for child locks, replace the seat cover.. See .

Installer

  1. With assistance, position the LH 2nd row seatback assembly into place, and then connect the electrical harness to the connector at the LH lower seat frame.
  2. Move the LH 2nd row seatback to vertical position.
  3. Install the bolts (x5) that attach the LH 2nd row seat back frame to the vehicle.
    37 Nm (27.3 lbs-ft)
    Note
    The two frontmost bolts are behind the main carpet.
    Note
    Torque in the sequence of:
    1. Front Outboard
    2. Rear Inboard
    3. Rear Outboard
    4. Front Inboard
    Tip
    L'un ou plusieurs des outils suivants sont recommandés :
    • Douille de 11mm
  4. Install the clips (x3) that attach the main carpet to the lower seat cushion frames.
  5. Install the LH lower C-pillar trim. See .