2026-06-12

Wheelhouse Extension (Rear)

Correction code: 10101920702, 10101920802 NOTE: Unless explicitly stated in the procedure, the above correction code includes all Collision Repair and Service repair work required to perform this procedure, including the linked Collision Repair procedures and linked Service procedures. Do not stack Collision Repair correction codes unless explicitly told to do so. Depending on the damage to the vehicle, additional repairs may be required.

Parts List

Quantity Description Image / Notes
1 MY Asy,WheelHouse Outer,SVC E-COATED (Wheelhouse Outer)
2

High Strength Structural Rivet, 6.5 mm

10

Rivet, 4.8 mm

2

Flow Form Rivet S08

1

Flow Form Rivet S18

2

Bolt, Torx-head

Tesla part number 1008833-01-A.
2

Nut

Tesla part number 1006628-01-A.

When ordering parts, refer to the Parts Catalog and enter the VIN of the vehicle being repaired to find the correct parts (and the part numbers) for the vehicle. Alternatively, use the search function in the Parts Catalog to find a specific part for the vehicle.

Repair Procedure

  1. Remove the Bracket - Rear Wing - LH (Remove and Replace).
  2. Remove the Air Extractor - LH (Remove and Replace).
  3. Remove the Wheel Arch Liner - Rear - LH (Structural Pack) (Remove and Replace).
  4. Remove the Insulator - Wheelhouse - LH (Remove and Replace).
  5. Remove the Wheelhouse Insulator - Rear - RH (Remove and Replace).
  6. Remove the original component.
    • or Factory Spot Welds
  7. Remove the original component.
    • or Factory Spot Welds
  8. Remove the Wheelhouse Rear Extension component from the MY Asy,WheelHouse Outer,SVC E-COATED service part.
  9. Prepare for installation.
    • Reference Line/Point
    • or Rivets, 4.8 mm A = 43 mm B = 7 mm
    • or Aluminum Plug Welds
    Informational PurposesAn informational icon, calling your attention
    Note
    For this plug weld, drill a 6 mm hole in the indicated location.
  10. Prepare for installation.
  11. Prepare for installation.
  12. Apply structural adhesive to the mating surfaces on the vehicle and the new component or components.
  13. Install the new component or components.
    Torque the bolts to 22 Nm.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure to cut the NVH foam under the subwoofer to allow for rivet clearance.
  14. Perform GMA welding.
    • or Aluminum Plug Welds
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Failure to follow all welding safety precautions, including the use of personal protective equipment, could result in serious injury or property damage. Only technicians who have completed Tesla’s approved welding training are authorized to weld structural components on Tesla vehicles.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    To maintain vehicle crash integrity, use only approved welding wire and an approved GMA welder to perform GMA welding on Tesla vehicles. Refer to Approved Gas Metal Arc (GMA) Welders and Welding Wire for information on approved GMA welders and welding wire.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not weld on a Tesla vehicle before performing the Vehicle Electrical Isolation Procedure (refer to the vehicle-specific Service Manual for more information on the Vehicle Electrical Isolation Procedure). Welding on a Tesla vehicle with an energized high or low voltage system might damage vehicle components.
    Informational PurposesAn informational icon, calling your attention
    Note
    Before GMA welding, a test weld using material of the same gauge and type should be performed to make sure that the welding equipment settings produce a satisfactory joint.
  15. Perform any necessary post-repair operations.
  16. Install the Wheelhouse Insulator - Rear - RH (Remove and Replace).
  17. Install the Insulator - Wheelhouse - LH (Remove and Replace).
  18. Install the Wheel Arch Liner - Rear - LH (Structural Pack) (Remove and Replace).
  19. Install the Air Extractor - LH (Remove and Replace).
  20. Install the Bracket - Rear Wing - LH (Remove and Replace).