2026-08-05

Elektromekanisk bremseforsterker (biler uten strukturell pakke) (venstrestyrt) (fjerne og skifte ut)

Korrigeringskode 33201002 1.62 MERK: Hvis ikke noe annet er uttrykkelig oppgitt i prosedyren, gjenspeiler korrigeringskoden og FRT ovenfor, alt arbeidet som kreves for å gjennomføre denne prosedyren, inkludert de tilknyttede prosedyrene. Ikke stable korrigeringskoder med mindre du bli uttrykkelig bedt om det. MERK: Se Flat rate-tider for å lære mer om FRT-er og hvordan de lages. MERK: Se Personlig beskyttelse for å forsikre deg om at du bruker riktig PVU når du gjennomfører prosedyren nedenfor. MERK: Se for trygge og sunne arbeidspraksiser.

  • 2023-12-27: Removed steps about removing and installing the underhood storage unit, 12V battery and wiper module.
Equipment:
  • 1079041-00-A Flare nut crowfoot set

Dreiemomentspesifikasjoner

Tabell 1. Dreiemomentspesifikasjoner: Elektromekanisk bremseforsterker (biler uten strukturell pakke) (venstrestyrt) (fjerne og skifte ut)
Beskrivelse Dreiemomentverdi Anbefalte verktøy Bruke på nytt / skifte ut Merknader
Forward brake line fastener
16 Nm (11.8 lbs-ft)
  • 12 mm 12pt combination wrench
  • 12 mm flare nut crowfoot socket
Bruke på nytt
Rear brake line fastener
16 Nm (11.8 lbs-ft)
  • 12 mm 12pt combination wrench
  • 12 mm flare nut crowfoot socket
Bruke på nytt
Nuts that attach the brake booster to the bulkhead
16.5 Nm (12.2 lbs-ft)
  • 13mm dypt uttak
  • 6 tommers forlengelse
Erstatt 1111541-00-A

Fjerne

  1. Open the LH front door and fully lower the LH front window.
  2. Move the driver seat fully rearward.
  3. Raise and support the vehicle. See .
  4. Remove the rear underhood apron. See Deksel under panser – bak (fjerne og skifte ut).
  5. Remove the HEPA filter assembly. See .
  6. Disconnect 12V power. See 12 V-/lavspenningsstrøm (koble fra og koble til).
  7. Release the locking tab, and then disconnect the brake fluid reservoir electrical connector.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ADVARSEL
    IKKE skyv ned på den røde låsetappen. Trekk tappen bort fra kontakten til kontakten er låst opp, og fortsett deretter å trekke i hoveddelen av kontakten for å koble den helt ut.
  8. Release the locking tab, and then disconnect the harness connectors from the brake booster assembly.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ADVARSEL
    IKKE skyv ned på den røde låsetappen. Trekk tappen bort fra kontakten til kontakten er låst opp, og fortsett deretter å trekke i hoveddelen av kontakten for å koble den helt ut.
  9. Place an absorbent material beneath the brake booster and reservoir area.
  10. Clean the area around the brake fluid reservoir, then remove the reservoir cap.
  11. Using a brake fluid syringe, remove the brake fluid from the reservoir.
  12. Disconnect the forward brake line from the master cylinder.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Bruk av følgende verktøy anbefales:
    • 12 mm 12pt combination wrench
    • 12 mm flare nut crowfoot socket
  13. Disconnect the rear brake line from the master cylinder.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Bruk av følgende verktøy anbefales:
    • 12 mm 12pt combination wrench
    • 12 mm flare nut crowfoot socket
  14. Remove the driver knee airbag. See .
  15. Remove the LH footwell air duct. See .
  16. Disconnect the brake switch electrical connector.
  17. Remove the brake switch from the pedal assembly.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Rotate the switch 45 degrees to remove it from the assembly.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ADVARSEL
    Replace if damaged during removal.
  18. Remove the cotter clip from the clevis pin on the brake pedal assembly.
  19. Remove the clevis pin from the brake pedal assembly.
  20. Remove and discard the nuts that attach the brake booster to the bulkhead, and then remove the brake booster assembly from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Bruk av følgende verktøy anbefales:
    • 13mm dypt uttak
    • 6 tommers forlengelse

Montere

  1. Position the brake booster assembly into the vehicle.
  2. Install new nuts that attach the brake booster to the bulkhead.
    16.5 Nm (12.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Bruk av følgende verktøy anbefales:
    • 13mm dypt uttak
    • 6 tommers forlengelse
  3. Align the brake pedal to the iBooster rod, and then install the clevis pin to the brake pedal assembly.
  4. Install the cotter clip to the clevis pin on the brake pedal assembly.
  5. Install the brake switch onto the pedal assembly by pushing the brake switch into the clip until it stops, twisting it clockwise 45 degrees to lock it in place, and ensuring the connector faces the RH side of the vehicle with the pins oriented vertically.
    Informational PurposesAn informational icon, calling your attention
    Merk
    • Confirm the brake pedal is in the home position. The iBooster and brake pedal must be assembled together before the brake light switch can be installed.
    • Do not push the brake switch too hard as it can move the brake pedal.
  6. Connect the brake switch electrical connector.
  7. Install the LH footwell air duct. See .
  8. Install the driver knee airbag. See .
  9. Connect the rear brake line to the master cylinder.
    16 Nm (11.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Bruk av følgende verktøy anbefales:
    • 12 mm 12pt combination wrench
    • 12 mm flare nut crowfoot socket
  10. Connect the forward brake line to the master cylinder.
    16 Nm (11.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Bruk av følgende verktøy anbefales:
    • 12 mm 12pt combination wrench
    • 12 mm flare nut crowfoot socket
  11. Clean the area around the brake fluid reservoir, and then remove the cap.
  12. Fill the brake fluid reservoir to the "MAX" level.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ADVARSEL
    Make sure not to get any brake fluid on any painted surface. Clean residual brake fluid with a shop towel.
  13. Remove the absorbent material from beneath the brake booster and reservoir area.
  14. Connect the harness connectors to the brake booster assembly, and then engage the locking tabs.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ADVARSEL
    Skyv den røde låsetappen mot kontakten for å aktivere låsemekanismen. IKKE skyv ned eller trekk opp på den røde låsetappen.
  15. Connect the brake fluid reservoir electrical connector, and then engage the locking tabs.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ADVARSEL
    Skyv den røde låsetappen mot kontakten for å aktivere låsemekanismen. IKKE skyv ned eller trekk opp på den røde låsetappen.
  16. Connect 12V power. See 12 V-/lavspenningsstrøm (koble fra og koble til).
  17. Redeploy firmware. See .
  18. Bleed the brakes. See .
  19. Install the HEPA filter assembly. See .
  20. Install the rear underhood apron. See Deksel under panser – bak (fjerne og skifte ut).
  21. Exit Service Mode Plus. See .
  22. Move the LH front seat to original position.
  23. Raise the LH front window and close the LH front door.
  24. Remove the vehicle from the lift.
  25. Perform a test drive.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Add correction code 00040100 as needed.