2026-05-04

펜더 어셈블리 - 전면 - LH(탈거 및 장착)

교정 코드 10103001 0.96 메모: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오. 메모: 안전하고 건강한 작업 사례는 의 내용을 참조하십시오.

  • 2026-03-11: Updated photo and location description of rear fender bolt.
This procedure assumes the cowl screen carrier bracket, headlight grommet, and underhood storage unit clips on the fender assembly being replaced are undamaged. Inspect these components and if necessary, replace with new parts.

Torque Specifications

Table 1. 토크 규격:
설명 토크 값 권장 공구 재사용/교체 참고
전면 페시아 상단부를 차량에 고정하는 볼트
4 Nm (2.9 lbs-ft)
  • 10mm 소켓
 재사용
LH 전면 휠 라이너를 HV 배터리에 고정하는 볼트
5 Nm (3.7 lbs-ft)
  • 10mm 소켓
 재사용
전면 페시아의 LH 모서리를 펜더에 고정하는 볼트
4 Nm (2.9 lbs-ft)
  • 10mm 소켓
 재사용
전면 페시아의 RH 모서리를 펜더에 고정하는 볼트
4 Nm (2.9 lbs-ft)
  • 10mm 소켓
 재사용
상단 LH 전면 펜더 브래킷을 차체에 고정하는 볼트
9.8 Nm (7.2 lbs-ft)
  • 10mm 딥소켓
 재사용
LH 전면 펜더 브래킷을 차체에 고정하는 볼트
9.8 Nm (7.2 lbs-ft)
  • 10mm 딥소켓
 재사용
후면 LH 전면 펜더 브래킷을 차체에 고정하는 볼트
9.8 Nm (7.2 lbs-ft)
  • 10mm 딥소켓
 재사용
하단 LH 전면 펜더 브래킷을 차체에 고정하는 너트
9.8 Nm (7.2 lbs-ft)
  • 10mm 딥소켓
 재사용

탈거

  1. Raise and support the vehicle. See .
  2. Open all doors and fully lower all windows.
  3. Remove the rear underhood apron. See 후드 내 에이프런 - 후면(탈거 및 교체).
  4. Remove the underhood storage unit. See 후드 내 보관 유닛(탈거 및 교체).
  5. Remove the bolts that attach the top of the front fascia to the vehicle.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구를 사용하는 것이 좋습니다.
    • 10mm 소켓
  6. Remove the front wheels. See .
  7. Remove the front aero shield panel. See 패널 - 에어로 실드 - 전면(구조용 팩 이외)(탈거 및 교체).
  8. Remove the LH front wheel liner. See 휠 아치 라이너 - 전면 - LH(구조용 팩 이외)(탈거 및 교체).
  9. Remove the bolt that attaches the LH corner of the front fascia to the fender.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구를 사용하는 것이 좋습니다.
    • 10mm 소켓
    Figure 1. LH shown; RH similar
  10. Remove the RH front fender garnish. See .
  11. Remove the clips (x6) that attach the front of the RH front wheel liner to the vehicle.
  12. Remove the bolt that attaches the RH corner of the front fascia to the fender.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구를 사용하는 것이 좋습니다.
    • 10mm 소켓
    Figure 2. LH shown; RH similar
  13. Disconnect the electrical connector from the front fascia in the RH wheel well.
  14. If present, release the clip that attaches the electrical harness to the pedestrian warning speaker assembly.
  15. If present, slide the locking tab away from the connector, and then press down on the locking tab to disconnect the connector from the pedestrian warning speaker assembly.
  16. With an assistant, release the LH side of the front fascia, and then carefully pull the fascia up and forward to remove it from the vehicle. Place the fascia on a padded surface.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Carefully release the tabs that attach the lower headlight bracket to the front fascia, otherwise the tabs can be broken.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    The corners of the ankle catcher are very sharp and might cause personal injury.

    LH ankle catcher corner shown; RH corner similar

  17. Remove the LH headlight. See .
  18. Remove the LH side repeater light. See .
  19. Remove the LH fascia side to fender bracket. See .
  20. Release the clip that attaches the cowl screen to the LH side of the carrier bracket.
  21. Remove the bolts that attach the upper LH front fender bracket to the body.
    9.8 Nm (7.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 딥소켓
  22. Remove the bolt that attaches the LH front fender bracket to the body.
    9.8 Nm (7.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 딥소켓
  23. Remove the bolt that attaches the rear LH front fender bracket to the body.
    9.8 Nm (7.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    The bolt is located outside the upper fender near the door hinge.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 딥소켓
  24. Remove the nuts that attach the lower LH front fender bracket to the body.
    9.8 Nm (7.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 딥소켓
  25. Remove the LH front fender assembly from the vehicle

장착

Informational PurposesAn informational icon, calling your attention
TIp
For instructions on how to align the fender, refer to .
  1. Install the front underhood storage fender clips onto the LH front fender.
  2. Position the LH front fender assembly onto the vehicle
  3. Install the nuts that attach the lower LH front fender bracket to the body.
    9.8 Nm (7.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 딥소켓
  4. Install the bolt that attaches the rear LH front fender bracket to the body.
    9.8 Nm (7.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    The bolt is located inside upper fender.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 딥소켓
  5. Install the bolt that attaches the LH front fender bracket to the body.
    9.8 Nm (7.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 딥소켓
  6. Install the bolts that attach the upper LH front fender bracket to the body.
    9.8 Nm (7.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 딥소켓
  7. Install the clip that attaches the cowl screen to the LH side of the carrier bracket.
  8. Install the LH fascia side to fender bracket. See .
  9. Install the LH side repeater light. See .
  10. Install the LH headlight from the vehicle. See .
  11. With an assistant, position the front fascia onto the vehicle. and then fasten the clips (x8).
  12. If present, install the clip that attaches the electrical harness to the pedestrian warning speaker assembly.
  13. If present, connect the pedestrian warning speaker electrical connector, and then engage the connector lock.
  14. Connect the electrical connector for the front fascia in the RH wheel well.
  15. Install the bolt that attaches the RH corner of the front fascia to the fender.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구를 사용하는 것이 좋습니다.
    • 10mm 소켓
    Figure 3. LH shown; RH similar
  16. Install the clips (x6) that attach the front of the RH front wheel liner to the vehicle.
  17. Install the RH front fender garnish. See .
  18. Install the bolt that attaches the LH corner of the front fascia to the fender.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구를 사용하는 것이 좋습니다.
    • 10mm 소켓
    Figure 4. LH shown; RH similar
  19. Install the LH front wheel liner. See 휠 아치 라이너 - 전면 - LH(구조용 팩 이외)(탈거 및 교체).
  20. Install the LH front fender garnish. See .
  21. Install the front aero shield panel. See 패널 - 에어로 실드 - 전면(구조용 팩 이외)(탈거 및 교체).
  22. Install the front wheels. See .
  23. Install the bolts that attach the top of the front fascia to the vehicle.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구를 사용하는 것이 좋습니다.
    • 10mm 소켓
  24. Install the underhood storage unit. See 후드 내 보관 유닛(탈거 및 교체).
  25. Install the rear underhood apron. See 후드 내 에이프런 - 후면(탈거 및 교체).
  26. Open all doors and fully lower all windows.
  27. Remove the vehicle from the lift.