2026-08-09

Teppe – foran – høyre (7-seter) (fjerne og skifte ut)

Korrigeringskode 15303112 0.66 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and its associated FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personlig beskyttelse to make sure wearing proper PPE when performing the below procedure. NOTE: See for safe and healthy working practices.

Fjerne

  1. Open all the doors and lower all the windows.
  2. Remove the passenger footwell cover assembly from the vehicle. See .
    Merk
    It is not necessary to remove components from the assembly after removal.
  3. Remove the RH center console side panel. See .
  4. Remove the bolts that attach the RH front of the center console to the body.
    Merk
    Bruk av følgende verktøy anbefales:
    • 10 mm nøkkel
  5. Remove the RH middle A-pillar trim. See .
  6. Remove the RH lower A-pillar trim. See .
  7. Release the RH front door seal from the body.
  8. Release the clip that attaches the RH front carpet to the body near the front of the RH door opening.
    Figur 1. LH shown; RH similar
  9. Fold the front of the RH front carpet rearward so that the RH body controller module and its surrounding connectors are exposed.
  10. Remove and discard the bolts (x2) that attach the front of the 1st row RH seat to the body.
    ADVARSEL
    Use only the Torx Plus T45 bit to remove the seat bolts.
    Merk
    Bruk av følgende verktøy anbefales:
    • Torx Plus T45-nøkkel
    Figur 2. LH shown; RH similar
  11. Move the seat fully forward.
  12. Raise RH front seat cushion to the maximum height.
    Merk
    Adjust the seat back if needed to avoid contacting the headliner.
  13. Sett utløsningsnøkkelen for sikkerhetsbeltet (1133787-00-A) inn nederst i beltestrammerkoblingen for å løsne sikkerhetsbeltet fra strammeren.
  14. Remove the center console lower rear panel. See #GUID-617524AB-052C-4C72-AE90-B152DC8B0B5C.
  15. Remove the bolt that attaches the RH rear of the center console to the body.
    Merk
    Bruk av følgende verktøy anbefales:
    • 10 mm nøkkel
  16. Remove and discard the bolts (x2) that attach the rear of the 1st row RH seat to the body.
    ADVARSEL
    Use only the Torx Plus T45 bit to remove the seat bolts.
    Merk
    Bruk av følgende verktøy anbefales:
    • Torx Plus T45-nøkkel
    Figur 3. LH shown; RH similar
  17. Move RH front seat to the middle of the track at the most upright position for easy removal.
  18. Remove the LH center console side panel. See .
  19. Remove the bolts that attach the LH front of the center console to the body.
    Merk
    Bruk av følgende verktøy anbefales:
    • 10 mm nøkkel
  20. Move the driver seat forward and the cushion to maximum height.
  21. Remove the bolt that attaches the LH rear of the center console to the body.
    Merk
    Bruk av følgende verktøy anbefales:
    • 10 mm nøkkel
  22. Remove the rear underhood apron. See Deksel under panser – bak (fjerne og skifte ut).
  23. Remove the HEPA filter assembly. See .
  24. Disconnect LV power. See 12 V-/lavspenningsstrøm (koble fra og koble til).
  25. Release the connector lock, and then disconnect the RH front seat harness from the RH body controller.\
    Merk
    Squeeze the release tab on the LH front seat connector lock, and then swing the lock away from the connector to release the lock.
    ADVARSEL
    Do not pull on the connector too hard. If the connector does not easily disconnect from the LH body controller, the lock is still engaged.
  26. Release the retaining clips (x2), and then remove the RH front seat harness from the RH footwell support bracket.
  27. Release the clips (x3) that attach the RH front seat harness to the RH front seat harness guide.
  28. Pull the RH front seat harness out from under the RH front carpet.
  29. With assistance, remove the seat from the vehicle.
    Merk
    Lift the seat, tilt the seat back, rotate the cushion toward the front door, and remove the seat from the vehicle, cushion first.
    ADVARSEL
    Take care not to damage the upholstery or trim while removing the seat.
    ADVARSEL
    If reinstalling the seat, place the seat in an area where it is not likely to be tipped over or otherwise damaged.
    Figur 4. LH shown; RH similar
  30. Disconnect the electrical connector that is located at the RH front of the center console.
  31. Disconnect the electrical connector from the rear of the center console.
  32. With an assistant, remove the center console from the vehicle as follows:
    1. Tilt the rear of the center console upwards.
    2. Pull the center console towards the rear of the vehicle.
    3. Tilt the front of the center console upwards.
    4. Remove the center console through the passenger front door.
  33. Remove the clips (x2) that attach the RH front carpet to the vehicle.
  34. Lift up the rear edge of the RH front carpet, and then slide the carpet out towards the rear of the vehicle to remove it.
    ADVARSEL
    Be careful to avoid the foam below catching on the seat risers.

Montere

  1. Position the RH front carpet into the vehicle.
  2. Install the clips (x2) that attach the RH front carpet to the vehicle.
  3. With an assistant, install the center console into the vehicle as follows:
    1. Tilt the front of the center console downwards.
    2. Slide the center console towards the front of the vehicle.
    3. Tilt the rear of the center console downwards until it is in place.
  4. Connect the electrical connector that is located at the RH front of the center console.
    ADVARSEL
    Ensure the connector is properly installed. Perform a push-pull test before continuing this procedure.
  5. 7 Nm (5.2 lbs-ft)
    Monter boltene som fester midtkonsollen i forkant på høyre side til karosseriet.
    Merk
    Bruk av følgende verktøy anbefales:
    • 10 mm nøkkel
  6. Install the RH center console side panel carpet. See #GUID-F4937396-BA44-41B6-87B7-8A7CFE6939D3.
  7. Install the passenger footwell cover assembly. See .
  8. Connect the electrical connector in the rear of the center console.
    ADVARSEL
    Ensure the connector is properly installed. Perform a push-pull test before continuing this procedure.
  9. 7 Nm (5.2 lbs-ft)
    Monter bolten som fester midtkonsollen i bakkant på høyre side til karosseriet.
    Merk
    Bruk av følgende verktøy anbefales:
    • 10 mm nøkkel
  10. 7 Nm (5.2 lbs-ft)
    Monter bolten som fester midtkonsollen i bakkant på venstre side til karosseriet.
    Merk
    Bruk av følgende verktøy anbefales:
    • 10 mm nøkkel
  11. Install the center console lower rear panel. See #GUID-617524AB-052C-4C72-AE90-B152DC8B0B5C.
  12. With assistance, position the 1st row LH seat in the vehicle.
    ADVARSEL
    Take care not to damage the upholstery or trim while positioning the seat.
  13. Secure the RH front seat harness under the RH front carpet.
  14. Secure the clips (x3) that attach the RH front seat harness to the RH front seat harness guide.
  15. Install the retaining clips (x2) that attach the RH front seat harness to the RH footwell support bracket.
  16. Connect the RH front seat harness to the RH body controller, and then secure the connector lock.
    Merk
    Ensure the connector and lock are fully engaged.
    ADVARSEL
    Perform a pull push pull test to ensure the connector and connector lock are seated.
  17. Fully the seat RH front carpet.
  18. Unfold the RH front carpet back into position, and then install the clip that attaches the carpet to the body near the front of the RH door opening.
    Figur 5. LH shown; RH similar
  19. Install the RH lower A-Pillar trim. See .
  20. Install the RH middle A-Pillar trim. See .
  21. Connect LV power. See 12 V-/lavspenningsstrøm (koble fra og koble til).
  22. Install the HEPA filter assembly. See .
  23. Install the rear underhood apron. See Deksel under panser – bak (fjerne og skifte ut).
  24. Move the RH front seat fully rearward.
  25. 33.5 Nm (24.7 lbs-ft)
    Sett inn nye bolter (2 stk.) for å feste forsiden av høyre sete på første rad til karosseriet.
    ADVARSEL
    Use only the Torx Plus T45 bit to install the seat bolts.
    Merk
    Bruk av følgende verktøy anbefales:
    • Torx Plus T45-nøkkel
    Figur 6. LH shown; RH similar
  26. Move the RH front seat fully forward.
  27. Install the RH 1st row seatbelt retractor onto the pretensioner.
    Merk
    Når du har montert beltestrammeren i beltestrammerkoblingen igjen, gjennomfører du en trekktest for å forsikre deg om at sikkerhetsbeltet og strammeren sitter godt fast.
    Figur 7. LH shown; RH similar
  28. 33.5 Nm (24.7 lbs-ft)
    Sett inn nye bolter (2 stk.) for å feste baksiden av høyre sete på første rad til karosseriet.
    ADVARSEL
    Use only the Torx Plus T45 bit to install the seat bolts.
    Merk
    Bruk av følgende verktøy anbefales:
    • Torx Plus T45-nøkkel
    Figur 8. LH shown; RH similar
  29. Move the RH front seat to the original position.
  30. Move the LH front seat rearward.
  31. 7 Nm (5.2 lbs-ft)
    Monter boltene som fester midtkonsollen i forkant på venstre side til karosseriet.
    Merk
    Bruk av følgende verktøy anbefales:
    • 10 mm nøkkel
  32. Install the LH center console side panel carpet. See #GUID-F4937396-BA44-41B6-87B7-8A7CFE6939D3.
  33. Move the LH front seat to the original position.
  34. Raise all the windows and close all the doors.