2026-06-03

Retractor - Seatbelt - 1st Row - LH (Remove and Replace)

Correction code 20054102 0.36 NOTA: Salvo explicitamente indicado em contrário no procedimento, o código de correção acima e o FRT refletem todo o trabalho necessário para a realização deste procedimento, incluindo os procedimentos associados. Não acumule códigos de correção, salvo se explicitamente instruído. NOTA: Consulte Tempos de taxa fixa para saber mais sobre FRT e sobre a respetiva criação. NOTA: Consulte Proteção pessoal para garantir que utiliza o EPI adequado durante a realização do procedimento abaixo. NOTA: Consulte para conhecer as práticas seguras e saudáveis de trabalho.

Equipment:
  • 1133787-00-A Key, Seat Belt Release, Model 3
  • 2024-11-26: Adjust the steps sequence based on feedback from engineering team.

Torque Specifications

Table 1. Torque Specifications: Retractor - Seatbelt - 1st Row - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Patch bolt that attaches the upper D-ring to the adjustable top loop
30 Nm (22.1 lbs-ft)
  • Torx T50 socket
 Replace
Bolts that attach the seat belt webbing guide to the B-pillar
5 Nm (3.7 lbs-ft)
  • 8 mm socket
 Replace
Patch bolt that attaches the seat belt retractor to the base of the B-pillar
40 Nm (29.5 lbs-ft)
  • 13 mm 12-point deep socket
 Replace

Remove

  1. Open the LH doors and lower the LH windows.
  2. Remove the LH instrument panel end cap. See .
  3. Remove the LH middle A-pillar trim. See #GUID-E1DDEA4B-6FBC-438D-997F-B3BD26910740.
  4. Remove the LH lower A-pillar trim. See #GUID-2B48046D-F15C-4E02-B2C9-82D80BB25389.
  5. Remove the lower portion of the LH front door seal from the body.
  6. Remove the LH front seat harness guide from the body.
  7. Move the front seats fully forward.
  8. Remove the rear underhood apron. See #GUID-513C83FE-1D5B-4FC1-B3EA-FA796E158252.
  9. Disconnect 12V power. See 12V/LV Power (Disconnect and Connect).
  10. Insert the seat belt release key (1133787-00-A) into the bottom of the seatbelt pretensioner coupling to release the seatbelt from the pretensioner.
  11. Remove the LH upper B-pillar trim. See .
  12. Release the 2nd row seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).
  13. Partially remove the lower portion of the LH rear door seal.
  14. Remove the LH lower C-pillar trim. See .
  15. Remove the LH lower B-pillar trim. See
  16. Remove and discard the bolts that attach the seat belt webbing guide to the B-pillar, and then remove the guide from the B-pillar.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 8 mm socket
  17. Remove and discard the patchbolt that attaches the upper D-ring to the top loop.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T50 socket
  18. Remove and discard the patchbolt that attaches the seat belt retractor to the base of the B-pillar.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13 mm 12-point deep socket
  19. Disconnect the electrical harness from the seat belt retractor connectors (x2).
    Informational PurposesAn informational icon, calling your attention
    Note
    For better access to the connectors, the retractor can be removed from the B-pillar first.
  20. Remove the LH front seatbelt from the vehicle.

Install

  1. Install the LH front seatbelt into the vehicle.
  2. Connect the electrical harness to the seat belt retractor connectors (x2).
  3. Install a new patchbolt to attach the seat belt retractor to the base of the B-pillar.
    40 Nm (29.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13 mm 12-point deep socket
  4. Install a new patchbolt to attach the upper D-ring to the top loop.
    30 Nm (22.1 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T50 socket
  5. Install the seat belt webbing guide to the B-pillar, and then install new bolts that attach the guide to the B-pillar.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 8 mm socket
  6. Install the LH lower B-pillar trim. See
  7. Install the LH lower C-pillar trim. See .
  8. Install the lower portion of the LH rear door seal that was partially removed.
  9. Install the 2nd row seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).
  10. Install the LH upper B-pillar trim. See .
  11. Install the LH front seatbelt pretensioner coupling onto the LH front seat pretensioner.
    Informational PurposesAn informational icon, calling your attention
    Note
    Perform a pull-push-pull test to verify the pretensioner and coupling are fully engaged.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Os vídeos incluídos neste procedimento destinam-se a ser utilizados como uma visão geral apenas para efeitos complementares. Siga todos os passos enumerados no procedimento para evitar danos nos componentes e/ou ferimentos.
  12. Connect 12V power. See 12V/LV Power (Disconnect and Connect).
  13. Install the rear underhood apron. See #GUID-513C83FE-1D5B-4FC1-B3EA-FA796E158252.
  14. Move the front seats fully rearward.
  15. Install the LH front seat harness guide to the body.
  16. Install the lower portion of the LH front door seal to the body.
  17. Install the LH lower A-pillar trim. See #GUID-2B48046D-F15C-4E02-B2C9-82D80BB25389.
  18. Install the LH middle A-pillar trim. See #GUID-E1DDEA4B-6FBC-438D-997F-B3BD26910740.
  19. Install the LH instrument panel end cap. See .
  20. Perform a pull test on the belt to ensure proper installation. Pull webbing up with force to ensure the pretensioner coupler was properly installed. Next, pull out all the webbing from the retractor. Webbing should smoothly retract after you have pulled it all out. Lastly, quickly tug at the webbing in a downward motion, retractor should lock.
  21. Close the LH doors and raise the LH windows.