2026-05-12

Fascia - Front (Remove and Install)

Correction code 10011001 0.48 NOTA: Salvo explicitamente indicado em contrário no procedimento, o código de correção acima e o FRT refletem todo o trabalho necessário para a realização deste procedimento, incluindo os procedimentos associados. Não acumule códigos de correção, salvo se explicitamente instruído. NOTA: Consulte Tempos de taxa fixa para saber mais sobre FRT e sobre a respetiva criação. NOTA: Consulte Proteção pessoal para garantir que utiliza o EPI adequado durante a realização do procedimento abaixo. NOTA: Consulte para conhecer as práticas seguras e saudáveis de trabalho.

Torque Specifications

Tabela 1. Torque Specifications: Fascia - Front (Remove and Install)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts that attach the top of the front fascia to the vehicle
4 Nm (2.9 lbs-ft)
  • 10 mm socket
 Reuse
Bolt that attaches the LH corner of the front fascia to the fender
4 Nm (2.9 lbs-ft)
  • 10 mm socket
 Reuse

Remove

  1. Open the LH front door.
  2. Remove the rear underhood apron. See #GUID-513C83FE-1D5B-4FC1-B3EA-FA796E158252.
  3. Remove the underhood storage unit. See .
  4. Remove the bolts that attach the top of the front fascia to the vehicle.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  5. Remove the LH front fender garnish. See
  6. Release the clips (x4) that attach the front portion of the LH front wheel arch liners to the vehicle, and then move the wheel arch liner aside to perform the following steps.
    Figure 1. LH shown; RH similar
  7. Remove the bolt that attaches the LH corner of the front fascia to the fender.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
    Figure 2. LH shown; RH similar
  8. Repeat step 5 through step 7 for the RH side of the vehicle.
  9. Remove the bolts that attach the front of the front aero shield to the vehicle.
    5 Nm (3.7 lbs-ft)
  10. Partially release the RH side of the front fascia.
  11. Disconnect the electrical connector from the front fascia in the RH wheel well.
  12. If present, release the clip that attaches the electrical harness to the pedestrian warning speaker assembly.
  13. If present, slide the locking tab away from the connector, and then press down on the locking tab to disconnect the connector from the pedestrian warning speaker assembly.
  14. With an assistant, release the LH side of the front fascia, and then carefully pull the fascia up and forward to remove it from the vehicle. Place the fascia on a padded surface.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Carefully release the tabs that attach the lower headlight bracket to the front fascia, otherwise the tabs can be broken.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    The corners of the ankle catcher are very sharp and might cause personal injury.

    LH ankle catcher corner shown; RH corner similar

Install

Installation procedure is the reverse of removal, except for the following:

  • Align the fascia to the fender before tightening the bolts that attach the fascia to the fender.
  • Perform a radar sensor calibration only if the front radar sensor likely moved outside of its calibration tolerance (contact while removing the fascia, etc.). See .
    Informational PurposesAn informational icon, calling your attention
    Note
    If radar sensor calibration is required, add the correction code separately.
  • Apply a thin bead of Loctite 222 to the threads of the bolts (x4) that attach the front aero shield panel to the vehicle.