2026-05-12

Knuckle - Suspension - Front - LH (Dual Motor) (Remove and Replace)

Correction code 31010112 0.72 NOTA: Salvo explicitamente indicado em contrário no procedimento, o código de correção acima e o FRT refletem todo o trabalho necessário para a realização deste procedimento, incluindo os procedimentos associados. Não acumule códigos de correção, salvo se explicitamente instruído. NOTA: Consulte Tempos de taxa fixa para saber mais sobre FRT e sobre a respetiva criação. NOTA: Consulte Proteção pessoal para garantir que utiliza o EPI adequado durante a realização do procedimento abaixo. NOTA: Consulte para conhecer as práticas seguras e saudáveis de trabalho.

    Torque Specifications

    Tabela 1. Torque Specifications: Knuckle - Suspension - Front - LH (Dual Motor) (Remove and Replace)
    Description Torque Value Recommended Tools Reuse/Replace Notes
    Bolts that attach the LH front brake dust shield to the knuckle
    8 Nm (5.9 lbs-ft)
    • Torx T30 socket
    		Reuse
    Bolt that attaches the LH front ABS wheel speed sensor to the LH front suspension knuckle
    5 Nm (3.7 lbs-ft)
    • 10 mm deep socket
    		Reuse
    Nut that attaches the LH tie rod end to the LH front suspension knuckle
    180 Nm (132.7 lbs-ft)
    • 22 mm socket
    • 12 pt 10mm combination wrench
    • 12 pt 22 mm combination wrench
    		 Replace 1109263-00-B
    Nut that attach the LH upper control arm to the LH front suspension knuckle
    56 Nm (41.3 lbs-ft)
    • Torx T47 socket
    • 12 pt 15 mm combination wrench
    		 Replace 1111145-00-A
    Nut that attaches the LH front lower compliance link to the front suspension knuckle
    180 Nm (132.7 lbs-ft)
    • 22 mm socket
    • 22 mm ratcheting combination wrench
    • Torx T45 socket
    		Replace 1109263-00-B
    Nut that attaches the LH front lower lateral link to the LH front suspension knuckle
    180 Nm (132.7 lbs-ft)
    • 22 mm socket
    • 22 mm ratcheting combination wrench
    • Torx T45 socket
    		Replace 1109263-00-B

    Remove

    1. Remove the LH front hub. See .
    2. Remove the bolts that attach the LH front brake dust shield to the knuckle, and then remove the dust shield from the vehicle.
      Informational PurposesAn informational icon, calling your attention
      TIp
      Use of the following tool(s) is recommended:
      • Torx T30 socket
    3. Remove the bolt that attaches the LH front ABS wheel speed sensor to the LH front suspension knuckle.
      Informational PurposesAn informational icon, calling your attention
      TIp
      Use of the following tool(s) is recommended:
      • 10 mm deep socket
    4. Release the clips that attach the LH front ABS wheel speed sensor electrical harness to the LH front suspension knuckle.
    5. Remove and discard the nut that attaches the LH tie rod end to the LH front suspension knuckle, and then remove the tie rod end from the knuckle.
      Informational PurposesAn informational icon, calling your attention
      TIp
      Use of the following tool(s) is recommended:
      • 22 mm socket
      • 12 pt 10mm combination wrench
      • 12 pt 22 mm combination wrench
    6. Remove the bolt and discard the nut that attach the LH upper control arm to the LH front suspension knuckle.
      Informational PurposesAn informational icon, calling your attention
      Note
      Compress the joint to remove the bolt.
      Informational PurposesAn informational icon, calling your attention
      TIp
      Use of the following tool(s) is recommended:
      • Torx T47 socket
      • 12 pt 15 mm combination wrench
    7. Remove and discard the nut that attaches the LH front lower compliance link to the front suspension knuckle.
      Informational PurposesAn informational icon, calling your attention
      TIp
      Use of the following tool(s) is recommended:
      • 22 mm socket
      • 22 mm ratcheting combination wrench
      • Torx T45 socket
    8. Remove and discard the nut that attaches the LH front lower lateral link to the LH front suspension knuckle.
      Informational PurposesAn informational icon, calling your attention
      TIp
      Use of the following tool(s) is recommended:
      • 22 mm socket
      • 22 mm ratcheting combination wrench
      • Torx T45 socket
    9. Remove the LH front suspension knuckle from the vehicle.

    Install

    1. Position the LH front suspension knuckle into the vehicle.
    2. Rest the LH front drive unit half shaft in the LH front suspension knuckle, and then install a new nut that attaches the knuckle to the lower lateral link.
      180 Nm (132.7 lbs-ft)
      Informational PurposesAn informational icon, calling your attention
      TIp
      Use of the following tool(s) is recommended:
      • 22 mm socket
      • 22 mm ratcheting combination wrench
      • Torx T45 socket
    3. Install a new nut that attaches the LH front lower compliance link to the LH front suspension knuckle.
      180 Nm (132.7 lbs-ft)
      Informational PurposesAn informational icon, calling your attention
      TIp
      Use of the following tool(s) is recommended:
      • 22 mm socket
      • 22 mm ratcheting combination wrench
      • Torx T45 socket
    4. Install the bolt and new nut that attach the LH upper control arm to the LH front suspension knuckle.
      56 Nm (41.3 lbs-ft)
      Informational PurposesAn informational icon, calling your attention
      TIp
      Use of the following tool(s) is recommended:
      • Torx T47 socket
      • 12 pt 15 mm combination wrench
    5. Install a new nut that attaches the LH tie rod end to the LH front suspension knuckle.
      180 Nm (132.7 lbs-ft)
      Informational PurposesAn informational icon, calling your attention
      TIp
      Use of the following tool(s) is recommended:
      • 22 mm socket
      • 12 pt 10mm combination wrench
      • 12 pt 22 mm combination wrench
    6. Install the clips that attach the LH front ABS wheel speed sensor electrical harness to the LH front suspension knuckle.
    7. Install the bolt that attaches the LH front ABS wheel speed sensor to the LH front suspension knuckle.
      5 Nm (3.7 lbs-ft)
      Informational PurposesAn informational icon, calling your attention
      TIp
      Use of the following tool(s) is recommended:
      • 10 mm deep socket
    8. Install the bolts that attach the LH front brake dust shield to the knuckle.
      8 Nm (5.9 lbs-ft)
      Informational PurposesAn informational icon, calling your attention
      TIp
      Use of the following tool(s) is recommended:
      • Torx T30 socket
    9. Install the LH front hub. See .
    10. Refer to the Alignment Requirement tables to determine whether an EPAS alignment check (EC) or four wheel alignment check (AC) is necessary. If performed, add the alignment check/adjust correction code as a separate activity to the SV. See .