2026-05-12

Airbag - Curtain - LH (Remove and Replace)

Correction code 20012002 1.62 NOTA: Salvo explicitamente indicado em contrário no procedimento, o código de correção acima e o FRT refletem todo o trabalho necessário para a realização deste procedimento, incluindo os procedimentos associados. Não acumule códigos de correção, salvo se explicitamente instruído. NOTA: Consulte Tempos de taxa fixa para saber mais sobre FRT e sobre a respetiva criação. NOTA: Consulte Proteção pessoal para garantir que utiliza o EPI adequado durante a realização do procedimento abaixo. NOTA: Consulte para conhecer as práticas seguras e saudáveis de trabalho.

  • 2026-02-20: Added note on using PROC_RCM_DISARM if using this procedure to diagnose the SRS.
  • 2-5-2024: Added note on varying number of curtain airbag fasteners.
Warning IconA warning icon, calling your attention to a possibly risky situation
Aviso
If using this procedure to diagnosis the vehicle's Supplemental Restraint Systems (SRS), disarm the RCM, which will prevent all airbags and pretensioners from deploying. Re-arm the RCM after all of the vehicle's SRS components are re-installed.
  • Disarm RCM:PROC_RCM_DISARMvia Service Mode Plus:
    • Safety & Restraints ➜ Airbags ➜ Disarm RCM
    • Safety & Restraints ➜ Seats ➜ Disarm RCM
    via Toolbox:(link)
  • Re-arm RCM:PROC_RCM_ARMvia Service Mode Plus:
    • Safety & Restraints ➜ Airbags ➜ Re-Arm RCM
    • Safety & Restraints ➜ Seats ➜ Re-Arm RCM
    via Toolbox:(link)
Warning IconA warning icon, calling your attention to a possibly risky situation
Aviso
Certifique-se de que a alimentação de 12 V/baixa tensão foi desligada há, no mínimo, 1 minuto antes de desligar a cablagem elétrica dos componentes do sistema de retenção suplementar (SRS), tais como módulo de controlo do sistema de retenção, sensores, airbags, etc. Desligue a bateria de 12 V/baixa tensão e o circuito de serviços de primeira intervenção. Se não o fizer, tal pode resultar em comportamentos indesejados do sistema de segurança. Para obter mais informações sobre precauções com o SRS, consulte .

Torque Specifications

Tabela 1. Torque Specifications: Airbag - Curtain - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts that attach the LH curtain airbag to the body
9 Nm (6.6 lbs-ft)
  • 10 mm socket
 Reuse

Remove

  1. Open all doors and fully lower all windows.
  2. Open the liftgate.
  3. Remove the front headliner. See .
  4. Remove the rear headliner. See .
  5. Remove the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).
  6. Disconnect 12V power. See 12V/LV Power (Disconnect and Connect).
  7. Disconnect the electrical harness from the LH curtain airbag connector.
  8. Remove the bolts that attach the front and center portions of the LH curtain airbag to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    The number of fasteners varies depending on vehicle build date/airbag revision.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  9. Remove the bolts that attach the rear portion of the LH curtain airbag to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    The number of fasteners varies depending on vehicle build date/airbag revision.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  10. Carefully release the clips (x8) that attach the LH curtain airbag to the side rail, and remove the airbag from the vehicle.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    If any clips are damaged, the airbag must be replaced.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    The airbag should always be handled by the igniter; the igniter should never be left dangling.
    Informational PurposesAn informational icon, calling your attention
    Note
    The number of fasteners varies depending on vehicle build date/airbag revision.

Install

  1. Install the LH curtain airbag to the side rail, and then carefully fasten the clips (x8) that attach the airbag to the side rail.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    If any clips are damaged, the airbag must be replaced.
    Informational PurposesAn informational icon, calling your attention
    Note
    The number of fasteners varies depending on vehicle build date/airbag revision.
  2. Install and hand-tighten the bolts that attach the rear portion of the LH curtain airbag to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    The number of fasteners varies depending on vehicle build date/airbag revision.
  3. Install and hand-tighten the bolts that attach the front and center portions of the LH curtain airbag to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    The number of fasteners varies depending on vehicle build date/airbag revision.
  4. Torque the bolts that attach the LH curtain airbag to the body.
    9 Nm (6.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  5. Connect the electrical harness to the LH curtain airbag connector.
  6. Install the rear headliner. See .
  7. Install the front headliner. See .
  8. Connect 12V power. See 12V/LV Power (Disconnect and Connect).
  9. Install the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).