2025-12-12

Brake Hose - Flexible - Front - LH (Remove and Replace)

Correction code 33030302 0.54 NOTA: Salvo explicitamente indicado em contrário no procedimento, o código de correção acima e o FRT refletem todo o trabalho necessário para a realização deste procedimento, incluindo os procedimentos associados. Não acumule códigos de correção, salvo se explicitamente instruído. NOTA: Consulte Tempos de taxa fixa para saber mais sobre FRT e sobre a respetiva criação. NOTA: Consulte Proteção pessoal para garantir que utiliza o EPI adequado durante a realização do procedimento abaixo. NOTA: Consulte para conhecer as práticas seguras e saudáveis de trabalho.

  • 2025-12-12: Removed the 12V/LV power connection/disconnection steps.
Equipment:

  • 1079041-00-A Flare nut crowfoot set

Warning IconA warning icon, calling your attention to a possibly risky situation
CAUTION
O líquido dos travões dissolve a pintura. Tenha a postos toalhas limpas e bastante água para lavar o líquido dos travões derramado sobre superfícies pintadas.
Informational PurposesAn informational icon, calling your attention
Note
Dispose of used brake fluid in a manner consistent with local environmental codes.

Remove

  1. Remove the rear underhood apron. See .
  2. Remove the front LH wheel. See #GUID-0B862D15-7178-4435-AEF2-0B40B8BEE686.
  3. Remove the bolt that attaches the brake hose bracket to the front LH knuckle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  4. Position the oil drain under the front LH brake hose.
  5. Remove the bolt that attaches the brake hose to the brake caliper, and allow the fluid to drain.
    Informational PurposesAn informational icon, calling your attention
    Note
    The bolt and washers (x2) are captive and cannot be reused. Replace the hose assembly if the bolt is loosened or removed.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 11 mm socket
    • Flex head ratchet/flex head torque wrench
  6. Remove the brake line tube nut from the brake hose at the jounce hose bracket, and allow the fluid to drain.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 12mm flare nut crowfoot socket
  7. Remove the nut that attaches the LH front jounce bracket to the vehicle, and then remove the LH front flexible brake hose from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm 12pt deep socket

Install

  1. Position the LH front flexible brake hose into the vehicle, and then install the nut that attaches the LH front jounce bracket to the vehicle.
    6 Nm (4.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm 12pt deep socket
  2. Insert the brake line into the brake hose at the jounce hose bracket, and then use a crowfoot extension to install the brake line tube nut into the brake hose.
    16 Nm (11.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 12mm flare nut crowfoot socket
  3. Install the brake hose to the brake caliper.
    42 Nm (31.0 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    The bolt and washers are captive in the new hose assembly.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 11 mm socket
  4. Remove the oil drain from under the vehicle.
  5. Install the brake hose to the front LH knuckle, and then install the bolt that attaches the brake hose bracket to the knuckle.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  6. Bleed the brake caliper for the brake hose that was serviced. See #GUID-242044A0-A455-4E05-A408-E9702C8BB268.
  7. Install the front LH wheel. See #GUID-0B862D15-7178-4435-AEF2-0B40B8BEE686.
  8. Install the rear underhood apron. See .
  9. Perform a road test and the brake pad burnishing procedure to ensure proper brake pedal feeling and performance. See .
    Informational PurposesAn informational icon, calling your attention
    Note
    Add the correction code for brake pad burnishing 33013000 as a separate activity to the Service Visit.