2026-05-04

Conjunto de la aleta guardabarros - Parte delantera - Lado izquierdo (Desinstalación e instalación)

Código de corrección 101030010.90 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección anterior y el FRT reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga. NOTA: Consulte Tiempos de tarifa plana (FRT) para obtener más información sobre los FRT y cómo se crean. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento. NOTA: Consulte para ver prácticas de trabajo seguras.

    This procedure assumes the cowl screen carrier bracket, headlight grommet, and underhood storage unit clips on the fender assembly being replaced are undamaged. Inspect these components and if necessary, replace with new parts.

    Retirar

    1. Raise and support the vehicle. See Elevación del vehículo - Elevador de 2 columnas.
    2. Remove the rear underhood apron. See Faldón del vano del motor - Parte trasera (Desinstalación y sustitución).
    3. Remove the cabin intake duct. See Conducto - Superior - Entrada de la cabina (Desinstalación y sustitución).
    4. Remove the hood latch cover. See Cubierta - Cierre del capó (Desinstalación y sustitución).
    5. Remove the underhood storage unit. See .
    6. Remove the LH shock tower cover. See Cubierta - Torre del amortiguador - Lado izquierdo (Desinstalación y sustitución).
    7. Remove the front wheels. See Conjunto de rueda (Desinstalación e instalación).
    8. Remove the front aero shield panel. See Panel - Deflector aerodinámico - Delantero (Desinstalación y sustitución).
    9. Remove the front fascia. See Defensa - Delantera (Desinstalación e instalación).
    10. Remove the LH headlight. See .
    11. Disconnect the electrical connectors (2x) from the front side repeater light.
    12. Release the two leftmost clips on the cowl screen panel from the LH front fender bracket.
    13. Remove the bolts that attach the upper LH front fender to the vehicle.
    14. Remove the bolt that attaches the lower LH front fender to the vehicle.
    15. Remove the bolt that attaches the rear LH front fender to the vehicle.
    16. Remove the bolt and nut that attach the lower LH front fender to the vehicle.
    17. Inspect the area between the upper LH front fender and the vehicle body for foam sealant. If present, carefully cut the sealant with a blade, and then separate the upper fender from the body with a plastic trim tool.
    18. Remove the LH front fender from the vehicle.
    19. Use a flat scraper blade and isopropyl alcohol (IPA) to remove the foam sealant from the LH outer shotgun panel. Any remaining sealant should be flush with the shotgun panel.
    20. Apply primer to the LH outer shotgun panel, completely covering the previous foam application area.

    Instalar

    Informational PurposesAn informational icon, calling your attention
    TIp
    For instructions on how to align the fender, refer to .
    1. Load urethane into a caulking gun, and then cut an opening that is 3.5 mm wide and 1.5 mm tall.
    2. Apply a dollop of urethane on top of the primed surface of the LH outer shotgun panel.
    3. Position the LH front fender on the vehicle.
    4. Install the bolt and nut that attach the lower LH front fender to the vehicle.
      9.8 Nm (7.2 lbs-ft)
      9.8 Nm (7.2 lbs-ft)
    5. Install the bolt that attaches the rear LH front fender to the vehicle.
      9.8 Nm (7.2 lbs-ft)
    6. Install the bolt that attaches the lower LH front fender to the vehicle.
      9.8 Nm (7.2 lbs-ft)
    7. Install the bolts that attach the upper LH front fender to the vehicle.
      9.8 Nm (7.2 lbs-ft)
    8. Install the cowl screen panel clips (2x) on the LH front fender bracket.
    9. Connect the electrical connectors (2x) to the front side repeater light.
    10. Install the LH headlight. See .
    11. Install the front fascia. See Defensa - Delantera (Desinstalación e instalación).
    12. Install the front aero shield panel. See Panel - Deflector aerodinámico - Delantero (Desinstalación y sustitución).
    13. Install the front wheels. See Conjunto de rueda (Desinstalación e instalación).
    14. Install the LH shock tower cover. See Cubierta - Torre del amortiguador - Lado izquierdo (Desinstalación y sustitución).
    15. For China, Japan and Korea only: Install a new motor ID label on the fender.
    16. Install the underhood storage unit. See .
    17. Install the hood latch cover. See Cubierta - Cierre del capó (Desinstalación y sustitución).
    18. Install the cabin intake duct. See Conducto - Superior - Entrada de la cabina (Desinstalación y sustitución).
    19. Install the rear underhood apron. See Faldón del vano del motor - Parte trasera (Desinstalación y sustitución).
    20. Remove the vehicle from the lift.