2026-05-04

Ensemble d’aile - avant - gauche (retirez et installez)

Code de correction 101030010.90 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. REMARQUE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous. REMARQUE : Voir pour consulter les pratiques de travail sécuritaires et saines.

    This procedure assumes the cowl screen carrier bracket, headlight grommet, and underhood storage unit clips on the fender assembly being replaced are undamaged. Inspect these components and if necessary, replace with new parts.

    Retirer

    1. Raise and support the vehicle. See Soulever le véhicule - pont élévateur à 2 poteaux.
    2. Remove the rear underhood apron. See Tablier sous le capot - arrière (retirez et remplacez).
    3. Remove the cabin intake duct. See Conduit - supérieur - admission de la cabine (retrait et remplacement).
    4. Remove the hood latch cover. See Couvercle - loquet de capot (retirez et remplacez).
    5. Remove the underhood storage unit. See .
    6. Remove the LH shock tower cover. See Couvercle - tour d’amortisseur - gauche (retirez et remplacez).
    7. Remove the front wheels. See Ensemble de roue (retrait et installation).
    8. Remove the front aero shield panel. See Panneau - écran aérodynamique - avant (retirez et remplacez).
    9. Remove the front fascia. See Carénage - avant (retirez et installez).
    10. Remove the LH headlight. See .
    11. Disconnect the electrical connectors (2x) from the front side repeater light.
    12. Release the two leftmost clips on the cowl screen panel from the LH front fender bracket.
    13. Remove the bolts that attach the upper LH front fender to the vehicle.
    14. Remove the bolt that attaches the lower LH front fender to the vehicle.
    15. Remove the bolt that attaches the rear LH front fender to the vehicle.
    16. Remove the bolt and nut that attach the lower LH front fender to the vehicle.
    17. Inspect the area between the upper LH front fender and the vehicle body for foam sealant. If present, carefully cut the sealant with a blade, and then separate the upper fender from the body with a plastic trim tool.
    18. Remove the LH front fender from the vehicle.
    19. Use a flat scraper blade and isopropyl alcohol (IPA) to remove the foam sealant from the LH outer shotgun panel. Any remaining sealant should be flush with the shotgun panel.
    20. Apply primer to the LH outer shotgun panel, completely covering the previous foam application area.

    Installer

    Informational PurposesAn informational icon, calling your attention
    TIp
    For instructions on how to align the fender, refer to .
    1. Load urethane into a caulking gun, and then cut an opening that is 3.5 mm wide and 1.5 mm tall.
    2. Apply a dollop of urethane on top of the primed surface of the LH outer shotgun panel.
    3. Position the LH front fender on the vehicle.
    4. Install the bolt and nut that attach the lower LH front fender to the vehicle.
      9.8 Nm (7.2 lbs-ft)
      9.8 Nm (7.2 lbs-ft)
    5. Install the bolt that attaches the rear LH front fender to the vehicle.
      9.8 Nm (7.2 lbs-ft)
    6. Install the bolt that attaches the lower LH front fender to the vehicle.
      9.8 Nm (7.2 lbs-ft)
    7. Install the bolts that attach the upper LH front fender to the vehicle.
      9.8 Nm (7.2 lbs-ft)
    8. Install the cowl screen panel clips (2x) on the LH front fender bracket.
    9. Connect the electrical connectors (2x) to the front side repeater light.
    10. Install the LH headlight. See .
    11. Install the front fascia. See Carénage - avant (retirez et installez).
    12. Install the front aero shield panel. See Panneau - écran aérodynamique - avant (retirez et remplacez).
    13. Install the front wheels. See Ensemble de roue (retrait et installation).
    14. Install the LH shock tower cover. See Couvercle - tour d’amortisseur - gauche (retirez et remplacez).
    15. For China, Japan and Korea only: Install a new motor ID label on the fender.
    16. Install the underhood storage unit. See .
    17. Install the hood latch cover. See Couvercle - loquet de capot (retirez et remplacez).
    18. Install the cabin intake duct. See Conduit - supérieur - admission de la cabine (retrait et remplacement).
    19. Install the rear underhood apron. See Tablier sous le capot - arrière (retirez et remplacez).
    20. Remove the vehicle from the lift.