2026-05-04

Skjermenhet – foran – venstre (fjerne og montere)

Korrigeringskode 101030010.90 MERK: Hvis ikke noe annet er uttrykkelig oppgitt i prosedyren, gjenspeiler korrigeringskoden og FRT ovenfor, alt arbeidet som kreves for å gjennomføre denne prosedyren, inkludert de tilknyttede prosedyrene. Ikke stable korrigeringskoder med mindre du bli uttrykkelig bedt om det. MERK: Se Flat rate-tider for å lære mer om FRT-er og hvordan de lages. MERK: Se Personlig beskyttelse for å forsikre deg om at du bruker riktig PVU når du gjennomfører prosedyren nedenfor. MERK: Se for trygge og sunne arbeidspraksiser.

    This procedure assumes the cowl screen carrier bracket, headlight grommet, and underhood storage unit clips on the fender assembly being replaced are undamaged. Inspect these components and if necessary, replace with new parts.

    Fjerne

    1. Raise and support the vehicle. See Heve bil – løftebukk med 2 stolper.
    2. Remove the rear underhood apron. See Deksel under panser – bak (fjerne og skifte ut).
    3. Remove the cabin intake duct. See Kanal – øvre – kupéinntak (fjerne og skifte ut).
    4. Remove the hood latch cover. See Deksel – panserlås (fjerne og skifte ut).
    5. Remove the underhood storage unit. See .
    6. Remove the LH shock tower cover. See Deksel – støtdempertårn - venstre (fjerne og skifte ut).
    7. Remove the front wheels. See Hjulenhet (fjerne og skifte ut).
    8. Remove the front aero shield panel. See Panel – luftskjerm – foran (fjerne og skifte ut).
    9. Remove the front fascia. See Støtfanger – foran (fjerne og montere).
    10. Remove the LH headlight. See .
    11. Disconnect the electrical connectors (2x) from the front side repeater light.
    12. Release the two leftmost clips on the cowl screen panel from the LH front fender bracket.
    13. Remove the bolts that attach the upper LH front fender to the vehicle.
    14. Remove the bolt that attaches the lower LH front fender to the vehicle.
    15. Remove the bolt that attaches the rear LH front fender to the vehicle.
    16. Remove the bolt and nut that attach the lower LH front fender to the vehicle.
    17. Inspect the area between the upper LH front fender and the vehicle body for foam sealant. If present, carefully cut the sealant with a blade, and then separate the upper fender from the body with a plastic trim tool.
    18. Remove the LH front fender from the vehicle.
    19. Use a flat scraper blade and isopropyl alcohol (IPA) to remove the foam sealant from the LH outer shotgun panel. Any remaining sealant should be flush with the shotgun panel.
    20. Apply primer to the LH outer shotgun panel, completely covering the previous foam application area.

    Montere

    Informational PurposesAn informational icon, calling your attention
    TIp
    For instructions on how to align the fender, refer to .
    1. Load urethane into a caulking gun, and then cut an opening that is 3.5 mm wide and 1.5 mm tall.
    2. Apply a dollop of urethane on top of the primed surface of the LH outer shotgun panel.
    3. Position the LH front fender on the vehicle.
    4. Install the bolt and nut that attach the lower LH front fender to the vehicle.
      9.8 Nm (7.2 lbs-ft)
      9.8 Nm (7.2 lbs-ft)
    5. Install the bolt that attaches the rear LH front fender to the vehicle.
      9.8 Nm (7.2 lbs-ft)
    6. Install the bolt that attaches the lower LH front fender to the vehicle.
      9.8 Nm (7.2 lbs-ft)
    7. Install the bolts that attach the upper LH front fender to the vehicle.
      9.8 Nm (7.2 lbs-ft)
    8. Install the cowl screen panel clips (2x) on the LH front fender bracket.
    9. Connect the electrical connectors (2x) to the front side repeater light.
    10. Install the LH headlight. See .
    11. Install the front fascia. See Støtfanger – foran (fjerne og montere).
    12. Install the front aero shield panel. See Panel – luftskjerm – foran (fjerne og skifte ut).
    13. Install the front wheels. See Hjulenhet (fjerne og skifte ut).
    14. Install the LH shock tower cover. See Deksel – støtdempertårn - venstre (fjerne og skifte ut).
    15. For China, Japan and Korea only: Install a new motor ID label on the fender.
    16. Install the underhood storage unit. See .
    17. Install the hood latch cover. See Deksel – panserlås (fjerne og skifte ut).
    18. Install the cabin intake duct. See Kanal – øvre – kupéinntak (fjerne og skifte ut).
    19. Install the rear underhood apron. See Deksel under panser – bak (fjerne og skifte ut).
    20. Remove the vehicle from the lift.