2024-07-10

车门安装环内件

Repair Information

只要使用本文档中车门安装环内件区块说明部分指定的参考切割线，即可更换车门安装环内件的任何一个区块或多个区块的任意组合。
Review all collision repair general practices and safety documentation and wear the appropriate PPE (Personal Protective Equipment) before beginning this procedure.
Properly mount the vehicle on a frame bench when performing this procedure.

Parts List


Quantity	Description	Image / Notes
1	MY ASY-DR RING INR（车门安装环内件）
9	Structural Bulb Rivet, 6.5 mm
4	High Strength Structural Rivet, 6.5 mm
6	Flow Form Rivet S18
6	Bolt BOLT & WSHR[FL],M8-1.25x32	Tesla 零件号 1119448-00-A。
1	Bolt T2000,M8x1.25-30	Tesla 零件号 1637725-00-A。
7	Bolt, Torx-head BOLT,TEP,M10-1.5x35	Tesla 零件号 1618776-00-B。

注

上面列出的铆钉数量用于整体维修。有关区块维修所需的紧固件，请参阅车门安装环内件区块说明。

When ordering parts, refer to the Parts Catalog and enter the VIN of the vehicle being repaired to find the correct parts (and the part numbers) for the vehicle. Alternatively, use the search function in the Parts Catalog to find a specific part for the vehicle.

车门安装环内件区块说明


车门安装环内件、次总成和次总成分区
车门安装环内件（如下所示）属于单个组件，可整体更换：	或者，也可以不更换整个车门安装环内件，而是使用本文档所述的切割线，分区域更换车门安装环内件维修零件的各个部分。

车门安装环内件（整体）	车门安装环内件区块


车门安装环内件区块说明
A 柱区块 Cut Line Reference Line/Point A = 62 mm. B = 105 mm. E = 206 mm. F = 138 mm. 注 Create a reinforcement plate 80 毫米宽，按指示安装。	铰链柱至 A 柱切割线 A 柱至 B 柱切割线铰链柱至 A 柱加固板 A 柱至 B 柱加固板
铰链柱区块 Cut Line Reference Line/Point A = 62 mm. B = 105 mm. C = 497 mm. D = 253 mm. 注 Create and install reinforcement plates 按指示安装。注每个加固板的宽度应为 80 毫米。	铰链柱至 A 柱切割线铰链柱至门槛切割线铰链柱至 A 柱加固板铰链柱至门槛加固板
B 柱区块 Cut Line Reference Line/Point E = 206 mm. F = 138 mm. G = 368 mm. H = 338 mm. 注 Create a reinforcement plate 80 毫米宽，按指示安装。	A 柱至 B 柱切割线 B 柱至门槛切割线 A 柱至 B 柱加固板门槛至 B 柱加固板
门槛区块 Cut Line Reference Line/Point C = 497 mm. D = 253 mm. G = 368 mm. H = 338 mm. 注 Create and install reinforcement plates 按指示安装。注每个加固板的宽度应为 80 毫米。	铰链柱至门槛切割线门槛至 B 柱切割线铰链柱至门槛加固板门槛至 B 柱加固板

Repair Procedure

拆下车门安装环外件的必要部分。
仅限铰链柱、门槛或 B 柱区块维修：拆卸侧门槛插件。
如果要更换车门安装环内件的某个区块：在车门安装环内件区块说明中指定的区块切割线位置标记车门安装环内件。
Remove the original component.

or Factory Spot Welds

Bolt
注
并非所有车辆上都存在红圈标示的螺栓。

or Bolt, Torx-head

注
保留螺栓，以供后续重新安装。
仅适用于区块维修： 按车门安装环内件区块说明中所述方式，制作衬垫板或加固板。
Prepare for installation.

注
A red X indicates a location where a factory-installed fastener is not being replaced.

or Installation Spot Welds

or High Strength Structural Rivets, 6.5 mm

or Structural Bulb Rivets, 6.5 mm

or Flow Form Rivets, S18

Bolt
注
仅当原装组件上有红圈标示的螺栓时才更换它。

or Bolt, Torx-head
Apply structural adhesive to the mating surfaces on the vehicle and the new component or components.
仅适用于区块维修： 按车门安装环内件区块说明中所述方式安装加固板。
Install the new component or components.
按如下所示拧紧螺栓：
- Bolt Tesla 零件号 1637725-00-A：48 Nm。
- Bolt Tesla 零件号 1119448-00-A：35 Nm。
- Bolt, Torx-head Tesla 零件号 1618776-00-B：65 Nm。
Perform resistance spot welding.

警告
Failure to follow all welding safety precautions, including the use of personal protective equipment, could result in serious injury or property damage. Only technicians who have completed Tesla’s approved welding training are authorized to weld structural components on Tesla vehicles.

警告
Do not weld on a Tesla vehicle before performing the Vehicle Electrical Isolation Procedure (refer to the vehicle-specific Service Manual for more information on the Vehicle Electrical Isolation Procedure). Welding on a Tesla vehicle with an energized high or low voltage system might damage vehicle components.
仅限铰链柱、门槛或 B 柱区块维修：安装侧门槛插件。
安装车门安装环外件的必要部分。
Perform any necessary post-repair operations.

车门安装环内件区块说明
A 柱区块 Cut Line Reference Line/Point A = 62 mm. B = 105 mm. E = 206 mm. F = 138 mm. 注 Create a reinforcement plate 80 毫米宽，按指示安装。	铰链柱至 A 柱切割线 A 柱至 B 柱切割线铰链柱至 A 柱加固板 A 柱至 B 柱加固板
铰链柱区块 Cut Line Reference Line/Point A = 62 mm. B = 105 mm. C = 497 mm. D = 253 mm. 注 Create and install reinforcement plates 按指示安装。注每个加固板的宽度应为 80 毫米。	铰链柱至 A 柱切割线铰链柱至门槛切割线铰链柱至 A 柱加固板铰链柱至门槛加固板
B 柱区块 Cut Line Reference Line/Point E = 206 mm. F = 138 mm. G = 368 mm. H = 338 mm. 注 Create a reinforcement plate 80 毫米宽，按指示安装。	A 柱至 B 柱切割线 B 柱至门槛切割线 A 柱至 B 柱加固板门槛至 B 柱加固板
门槛区块 Cut Line Reference Line/Point C = 497 mm. D = 253 mm. G = 368 mm. H = 338 mm. 注 Create and install reinforcement plates 按指示安装。注每个加固板的宽度应为 80 毫米。	铰链柱至门槛切割线门槛至 B 柱切割线铰链柱至门槛加固板门槛至 B 柱加固板