2026-05-04

Fender Assembly - Front - LH (Remove and Install)

校正代码 10103001 0.96 注意：除非本程序中另有明确规定，否则上述校正代码和 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。 注意：请参阅平均维修工时，深入了解 FRT 及其创建方式。 注意：请参阅人员保护，确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。注意：请参阅查看安全健康的作业规程。

  • 2026-03-11: Updated photo and location description of rear fender bolt.
This procedure assumes the cowl screen carrier bracket, headlight grommet, and underhood storage unit clips on the fender assembly being replaced are undamaged. Inspect these components and if necessary, replace with new parts.

Torque Specifications

Table 1. 扭矩规格:
描述 扭矩值 推荐工具 重复使用/更换 备注
Bolts that attach the top of the front fascia to the vehicle
4 Nm (2.9 lbs-ft)
  • 10 毫米套筒扳手
 重复使用
Bolt that attaches the LH front wheel liner to the HV battery
5 Nm (3.7 lbs-ft)
  • 10 mm socket
 重复使用
Bolt that attaches the LH corner of the front fascia to the fender
4 Nm (2.9 lbs-ft)
  • 10 mm socket
 重复使用
Bolt that attaches the RH corner of the front fascia to the fender
4 Nm (2.9 lbs-ft)
  • 10 mm socket
 重复使用
Bolts that attach the upper LH front fender bracket to the body
9.8 Nm (7.2 lbs-ft)
  • 10 mm deep socket
 重复使用
Bolt that attaches the LH front fender bracket to the body
9.8 Nm (7.2 lbs-ft)
  • 10 mm deep socket
 重复使用
Bolt that attaches the rear LH front fender bracket to the body
9.8 Nm (7.2 lbs-ft)
  • 10 mm deep socket
 重复使用
Nuts that attach the lower LH front fender bracket to the body
9.8 Nm (7.2 lbs-ft)
  • 10 mm deep socket
 重复使用

拆卸

  1. Raise and support the vehicle. See .
  2. Open all doors and fully lower all windows.
  3. Remove the rear underhood apron. See #GUID-513C83FE-1D5B-4FC1-B3EA-FA796E158252.
  4. Remove the underhood storage unit. See .
  5. Remove the bolts that attach the top of the front fascia to the vehicle.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具
    • 10 毫米套筒扳手
  6. Remove the front wheels. See .
  7. Remove the front aero shield panel. See .
  8. Remove the LH front wheel liner. See .
  9. Remove the bolt that attaches the LH corner of the front fascia to the fender.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具
    • 10 mm socket
    Figure 1. LH shown; RH similar
  10. Remove the RH front fender garnish. See .
  11. Remove the clips (x6) that attach the front of the RH front wheel liner to the vehicle.
  12. Remove the bolt that attaches the RH corner of the front fascia to the fender.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具
    • 10 mm socket
    Figure 2. LH shown; RH similar
  13. Disconnect the electrical connector from the front fascia in the RH wheel well.
  14. If present, release the clip that attaches the electrical harness to the pedestrian warning speaker assembly.
  15. If present, slide the locking tab away from the connector, and then press down on the locking tab to disconnect the connector from the pedestrian warning speaker assembly.
  16. With an assistant, release the LH side of the front fascia, and then carefully pull the fascia up and forward to remove it from the vehicle. Place the fascia on a padded surface.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Carefully release the tabs that attach the lower headlight bracket to the front fascia, otherwise the tabs can be broken.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    The corners of the ankle catcher are very sharp and might cause personal injury.

    LH ankle catcher corner shown; RH corner similar

  17. Remove the LH headlight. See .
  18. Remove the LH side repeater light. See .
  19. Remove the LH fascia side to fender bracket. See .
  20. Release the clip that attaches the cowl screen to the LH side of the carrier bracket.
  21. Remove the bolts that attach the upper LH front fender bracket to the body.
    9.8 Nm (7.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm deep socket
  22. Remove the bolt that attaches the LH front fender bracket to the body.
    9.8 Nm (7.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm deep socket
  23. Remove the bolt that attaches the rear LH front fender bracket to the body.
    9.8 Nm (7.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    The bolt is located outside the upper fender near the door hinge.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm deep socket
  24. Remove the nuts that attach the lower LH front fender bracket to the body.
    9.8 Nm (7.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm deep socket
  25. Remove the LH front fender assembly from the vehicle

安装

Informational PurposesAn informational icon, calling your attention
TIp
For instructions on how to align the fender, refer to .
  1. Install the front underhood storage fender clips onto the LH front fender.
  2. Position the LH front fender assembly onto the vehicle
  3. Install the nuts that attach the lower LH front fender bracket to the body.
    9.8 Nm (7.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm deep socket
  4. Install the bolt that attaches the rear LH front fender bracket to the body.
    9.8 Nm (7.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    The bolt is located inside upper fender.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm deep socket
  5. Install the bolt that attaches the LH front fender bracket to the body.
    9.8 Nm (7.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm deep socket
  6. Install the bolts that attach the upper LH front fender bracket to the body.
    9.8 Nm (7.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm deep socket
  7. Install the clip that attaches the cowl screen to the LH side of the carrier bracket.
  8. Install the LH fascia side to fender bracket. See .
  9. Install the LH side repeater light. See .
  10. Install the LH headlight from the vehicle. See .
  11. With an assistant, position the front fascia onto the vehicle. and then fasten the clips (x8).
  12. If present, install the clip that attaches the electrical harness to the pedestrian warning speaker assembly.
  13. If present, connect the pedestrian warning speaker electrical connector, and then engage the connector lock.
  14. Connect the electrical connector for the front fascia in the RH wheel well.
  15. Install the bolt that attaches the RH corner of the front fascia to the fender.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具
    • 10 mm socket
    Figure 3. LH shown; RH similar
  16. Install the clips (x6) that attach the front of the RH front wheel liner to the vehicle.
  17. Install the RH front fender garnish. See .
  18. Install the bolt that attaches the LH corner of the front fascia to the fender.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具
    • 10 mm socket
    Figure 4. LH shown; RH similar
  19. Install the LH front wheel liner. See .
  20. Install the LH front fender garnish. See .
  21. Install the front aero shield panel. See .
  22. Install the front wheels. See .
  23. Install the bolts that attach the top of the front fascia to the vehicle.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具
    • 10 毫米套筒扳手
  24. Install the underhood storage unit. See .
  25. Install the rear underhood apron. See #GUID-513C83FE-1D5B-4FC1-B3EA-FA796E158252.
  26. Open all doors and fully lower all windows.
  27. Remove the vehicle from the lift.