2026-06-03

Retractor - Seatbelt - 1st Row - LH (Remove and Replace)

Correction code 20054102 0.42 NOTA: Salvo diversa ed esplicita indicazione nella procedura, il codice modifica e il tempo forfettario, o FRT, riflettono tutto il lavoro richiesto per l'esecuzione di questa procedura, incluse le procedure collegate. Non cumulare i codici modifica a meno che non venga detto esplicitamente di farlo. NOTA: Consultare la Tempistica tariffe fisse per saperne di più sui tempi forfettari e su come essi vengono creati. NOTA: Consultare Protezione personale per assicurarsi di indossare i DPI adatti quando si esegue la procedura descritta di seguito. NOTA: Vedere per le pratiche di lavoro in sicurezza.

Equipment:
  • 1133787-00-A Key, Seat Belt Release, Model 3

Torque Specifications

Table 1. Torque Specifications: Retractor - Seatbelt - 1st Row - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Patch bolt that attaches the upper D-ring to the adjustable top loop
30 Nm (22.1 lbs-ft)
  • Torx T50 socket
 Replace
Bolts that attach the seat belt webbing guide to the B-pillar
5 Nm (3.7 lbs-ft)
  • 8 mm socket
 Replace
Patch bolt that attaches the seat belt retractor to the base of the B-pillar
40 Nm (29.5 lbs-ft)
  • 13 mm 12-point deep socket
 Replace

Remove

  1. Remove the LH instrument panel end cap. See End Cap - Instrument Panel - LH (Remove and Replace).
  2. Remove the LH middle A-pillar trim. See Trim - A-Pillar - Middle - LH (Remove and Replace).
  3. Remove the LH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  4. Insert the seat belt release key (1133787-00-A) into the bottom of the seatbelt pretensioner coupling to release the seatbelt from the pretensioner.
  5. Remove the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).
  6. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  7. Disconnect 12V power. See 12V/LV Power (Disconnect and Connect).
  8. Remove the LH 2nd row seat side bolster. See Bolster - Side - Seat - 2nd Row - LH (Remove and Replace).
  9. Remove the LH rear sill panel trim. See Trim - Sill Panel - Rear - LH (Remove and Replace).
  10. Release the clips that attach the LH upper B-pillar trim to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Release the clips at the bottom of the LH upper B-pillar trim first, and then release the clips at the top of the trim.
  11. Slide the seatbelt out through the hole in the LH upper B-pillar trim, and then set the trim aside.
  12. Remove the LH lower B-pillar trim. SeeTrim - B-Pillar - Lower - LH (Remove and Replace).
  13. Remove and discard the bolts that attach the seat belt webbing guide to the B-pillar, and then remove the guide from the B-pillar.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 8 mm socket
  14. Remove and discard the patchbolt that attaches the upper D-ring to the top loop.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T50 socket
  15. Remove and discard the patchbolt that attaches the seat belt retractor to the base of the B-pillar.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13 mm 12-point deep socket
  16. Disconnect the electrical harness from the seat belt retractor connectors (x2).
    Informational PurposesAn informational icon, calling your attention
    Note
    For better access to the connectors, the retractor can be removed from the B-pillar first.
  17. Remove the LH front seatbelt from the vehicle.

Install

  1. Install the LH front seatbelt into the vehicle.
  2. Connect the electrical harness to the seat belt retractor connectors (x2).
  3. Install a new patchbolt to attach the seat belt retractor to the base of the B-pillar.
    40 Nm (29.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13 mm 12-point deep socket
  4. Install a new patchbolt to attach the upper D-ring to the top loop.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T50 socket
  5. Install the seat belt webbing guide to the B-pillar, and then install new bolts that attach the guide to the B-pillar.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 8 mm socket
  6. Slide the seatbelt in through the hole in the LH upper B-pillar trim.
  7. Install the LH lower B-pillar trim. SeeTrim - B-Pillar - Lower - LH (Remove and Replace).
  8. Fasten the clips that attach the LH upper B-pillar trim to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Fasten the clips at the top of the LH upper B-pillar trim first, and then fasten the clips at the bottom of the trim.
  9. Install the LH rear sill panel trim. See Trim - Sill Panel - Rear - LH (Remove and Replace).
  10. Install the LH 2nd row seat side bolster. See Bolster - Side - Seat - 2nd Row - LH (Remove and Replace).
  11. Connect 12V power. See 12V/LV Power (Disconnect and Connect).
  12. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  13. Install the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).
  14. Install the LH front seatbelt pretensioner coupling onto the LH front seat pretensioner.
    Informational PurposesAn informational icon, calling your attention
    Note
    Perform a pull-push-pull test to verify the pretensioner and coupling are fully engaged.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    I video inclusi in questa procedura hanno il solo scopo di fornire una panoramica supplementare. Seguire tutti i passaggi elencati nella procedura per evitare danni ai componenti e/o lesioni personali.
  15. Install the LH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  16. Install the LH middle A-pillar trim. See Trim - A-Pillar - Middle - LH (Remove and Replace).
  17. Install the LH instrument panel end cap. See End Cap - Instrument Panel - LH (Remove and Replace).