2026-05-12

Door Assembly - Charge Port (NA) (Harness Type) (Remove and Replace)

Correction code 44011502 0.54 NOTA: Salvo diversa ed esplicita indicazione nella procedura, il codice modifica e il tempo forfettario, o FRT, riflettono tutto il lavoro richiesto per l'esecuzione di questa procedura, incluse le procedure collegate. Non cumulare i codici modifica a meno che non venga detto esplicitamente di farlo. NOTA: Consultare la Tempistica tariffe fisse per saperne di più sui tempi forfettari e su come essi vengono creati. NOTA: Consultare Protezione personale per assicurarsi di indossare i DPI adatti quando si esegue la procedura descritta di seguito. NOTA: Vedere per le pratiche di lavoro in sicurezza.

  • 2025-07-30: Updated LV harness images.
  • 2023-10-27: Update charge port to body bolt torque to 9 Nm.
  • 2023-10-10: Add a caution to not manually close the charge port door.
Apparecchiatura:
  • 1076921-00-B Insulation Multimeter, Fluke 1507 (NA)
  • 1108272-00-B Cap, Logic Conn, Inv, 3DU
  • 1130480-00-A Test Probes, Slim, Fluke TP38
Warning IconA warning icon, calling your attention to a possibly risky situation
Avvertenza

Solo i tecnici che hanno completato tutti i corsi di certificazione richiesti sono autorizzati a eseguire questa procedura. Tesla raccomanda ai tecnici di fornitori di terze parti di seguire una formazione equivalente prima di svolgere la presente procedura. Per maggiori informazioni sui requisiti dei Tecnici Tesla, o per le descrizioni degli argomenti richiesti per i tecnici di fornitori terzi, vedere i Requisiti per certificazioni HV. Ogni volta che si maneggia un raccordo, una barra di distribuzione o un cavo ad alta tensione è necessario indossare idonei dispositivi di protezione individuale (DPI) e guanti isolanti per l'alta tensione con classe di protezione minima 0 (1000 V). Per ulteriori informazioni sulla sicurezza, fare riferimento alle Note tecniche relative ai rischi dell'alta tensione TN-15-92-003, "High Voltage Awareness Care Points".

Warning IconA warning icon, calling your attention to a possibly risky situation
Avvertenza

Togliere tutti i gioielli (orologi, bracciali, anelli, collane, orecchini, medagliette, piercing, ecc.) e tutti gli oggetti (chiavi, monete, penne, matite, strumenti, dispositivi di fissaggio, ecc.) dalle tasche prima di eseguire qualsiasi procedura in presenza di alta tensione.

Warning IconA warning icon, calling your attention to a possibly risky situation
Avvertenza
Se è necessario indossare occhiali da vista per eseguire in sicurezza qualsiasi procedura, assicurarsi che gli occhiali siano fissati saldamente alla testa e non possano cadere.
Warning IconA warning icon, calling your attention to a possibly risky situation
Avvertenza

Proper Personal Protective Equipment (PPE) is required to perform this procedure:

  • High Voltage (HV) insulating gloves
  • Leather glove protectors
  • High voltage glove tester
  • Safety glasses
  • Electrical hazard rated safety shoes
Warning IconA warning icon, calling your attention to a possibly risky situation
Avvertenza

A glove inflator is the only recommended way to test HV gloves. Both HV gloves must pass testing before beginning this procedure. If either glove does not pass the air check, discard the pair.

Warning IconA warning icon, calling your attention to a possibly risky situation
Avvertenza

Make sure that the HV gloves are not expired. HV gloves can be used up to 12 months after the testing date printed on the glove, but only 6 months after first use even if the gloves are still within the 12-month period.

Warning IconA warning icon, calling your attention to a possibly risky situation
Avvertenza
I video inclusi in questa procedura hanno il solo scopo di fornire una panoramica supplementare. Seguire tutti i passaggi elencati nella procedura per evitare danni ai componenti e/o lesioni personali.

Remove

  1. Open the LH doors and lower all the windows.
  2. While pressing the LH and RH tabs towards the LH side of the vehicle, lift the front edge of the seat cushion to partially release the cushion.
  3. Open the trunk.
  4. Open the charge port door.
  5. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  6. Disconnect 12V power. See 12V/LV Power (Disconnect and Connect).
  7. Perform the charge port voltage check procedure. See .
  8. Remove the trunk garnish. See Garnish - Trunk (Remove and Replace).
  9. Remove the trunk floor trim. See Trim - Floor - Trunk (Remove and Replace).
  10. Remove the trunk sill trim panel. See Trim - Sill - Trunk (Remove and Replace).
  11. Disconnect the LH trunk task light electrical connector.
  12. Release the clip that attaches the edge of the trunk carpet, move the LH trunk side trim aside, and then tuck the carpet under the trim.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Be careful not to cause excessive creasing.
  13. Remove the LH taillight. See Taillight - LH (Remove and Replace).
  14. Apply masking tape around the charge port area.
  15. Release the clips (x2) that attach the harness to the body.
  16. Remove the bolts that attach the charge port assembly to the body, and then release the assembly from the body.
  17. Disconnect the low voltage electrical connectors from the charge port ECU.
  18. Release the charge port door grommet from the body.
  19. Pull the charge port door assembly towards the rear of the vehicle. When the door actuator reaches the rear of the quarter panel, pull the charge port downward to clear the actuator mechanism, and then pull out and away from the body to remove it from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Manipulation of the charge port door may be necessary to fully remove the assembly.

Install

  1. Position the charge port door assembly into the vehicle by pivoting the assembly so the actuator mechanism clears underneath the quarter panel, and then slide the charge door forward toward the rear door.
    Informational PurposesAn informational icon, calling your attention
    Note
    Manipulation of the charge door may be necessary to fully align the assembly to the body.
  2. Install the charge port door grommet to the body.
  3. Connect the low voltage electrical connectors from the charge port ECU.
  4. Install the bolts that attach the charge port door assembly to the body.
    9 Nm (6.6 lbs-ft)
  5. Secure the clips (x2) that attach the harness to the body.
  6. Install the LH taillight. See Taillight - LH (Remove and Replace).
  7. Move the LH trunk side trim back to the original position, and then secure the clip that attaches the trim to the body.
  8. Connect the LH trunk task light electrical connector.
  9. Install the trunk sill trim panel. See Trim - Sill - Trunk (Remove and Replace).
  10. Install the trunk floor trim. See Trim - Floor - Trunk (Remove and Replace).
  11. Install the trunk garnish. See Garnish - Trunk (Remove and Replace).
  12. Reconnect 12V power. See 12V/LV Power (Disconnect and Connect).
  13. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  14. Install the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).
  15. Verify the charging system is operating correctly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use the customer's charging equipment if available. Ensure all the charging adapters are present.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not try to manually close the charge port door.
  16. Remove the masking tape from the charge port door area.
  17. Raise all the windows and close all the doors.