2026-05-12

Taillight - LH (Remove and Replace)

Correction code 17402002 0.12 NOTA: Salvo diversa ed esplicita indicazione nella procedura, il codice modifica e il tempo forfettario, o FRT, riflettono tutto il lavoro richiesto per l'esecuzione di questa procedura, incluse le procedure collegate. Non cumulare i codici modifica a meno che non venga detto esplicitamente di farlo. NOTA: Consultare la Tempistica tariffe fisse per saperne di più sui tempi forfettari e su come essi vengono creati. NOTA: Consultare Protezione personale per assicurarsi di indossare i DPI adatti quando si esegue la procedura descritta di seguito. NOTA: Vedere per le pratiche di lavoro in sicurezza.

  • 2025-11-06: Added images for mounting bolt and electrical connector gaskets.
Apparecchiatura:
  • 1460222-00-B SKT, BUMP STOP, MDL 3

Remove

  1. Open the trunk, and then use the bump stop removal tool to remove the LH trunk stop.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not use other tools to twist off the trunk stop as this could damage the taillight or trunk stop.
  2. Remove the trunk garnish. See Garnish - Trunk (Remove and Replace).
  3. Carefully pull back the trunk trim carpet to expose the taillight, and then disconnect the electrical harness from the taillight connector.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    If the connector has a red locking tab: NON premere sulla linguetta di blocco rossa. Tirare la linguetta allontanandola dal connettore fino a sbloccarlo, quindi continuare a tirare il corpo principale del connettore per scollegarlo completamente.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    If the taillight must be replaced because of water ingress, place a shop towel under the taillight connector to prevent damage to other electrical components.
  4. Remove the nuts (x2) that attach the taillight to the body.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 8 mm 12-point deep socket
  5. Remove the LH taillight assembly from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Lift the trunk seal for better clearance.
  6. Remove and discard the grommets (x2) from the body.

Install

  1. Install the gaskets around each taillight mounting bolt (x2) and the taillight electrical connector (x1).
  2. Install new grommets (x2) into the body.
  3. Position the LH taillight studs into the grommets, and then install the taillight onto the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    Reseat the trunk seal over the LH taillight.
  4. Install the nuts (x2) that attach the taillight to the vehicle.
    3.2 Nm (2.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 8 mm 12-point deep socket
  5. Connect the electrical harness to the taillight connector.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    If the connector has a red locking tab: Premere la linguetta di blocco rossa nel connettore per inserire il blocco del connettore.
  6. Tuck the trunk trim carpet back into position.
  7. Install the LH bump stop using the bump stop removal tool.
  8. Close the trunk.
  9. Connect a laptop with Toolbox 3 to the vehicle. See .
  10. In Toolbox, perform one of the following according to the taillight that was replaced.
    • LH Taillight - Click the Actions tab, type "VCLEFT" in the search field, click on TEST-RESET_VCLEFTvia Service Mode Plus:Chassis ➜ SCCM ➜ Reset VCLeftvia Toolbox:(link), click Run, and then allow the routine to complete.
    • RH Taillight - Click the Actions tab, type "VCRIGHT" in the search field, click on TEST-RESET_VCRIGHTvia Toolbox:(link), click Run, and then allow the routine to complete.
  11. Disconnect the laptop with Toolbox 3 from the vehicle. See .