2023-10-09

Door Assembly - Charge Port (Busbar Type) (EMEA) (Remove and Replace)

Correction code 44011532 0.78 NOTA: Salvo diversa ed esplicita indicazione nella procedura, il codice modifica e il tempo forfettario, o FRT, riflettono tutto il lavoro richiesto per l'esecuzione di questa procedura, incluse le procedure collegate. Non cumulare i codici modifica a meno che non venga detto esplicitamente di farlo. NOTA: Consultare la Tempistica tariffe fisse per saperne di più sui tempi forfettari e su come essi vengono creati. NOTA: Consultare Protezione personale per assicurarsi di indossare i DPI adatti quando si esegue la procedura descritta di seguito. NOTA: Vedere per le pratiche di lavoro in sicurezza.

  • 2023-06-06: Added step to install the CKL Charging Identifier Label if one was present on the original part.
  • 2023-10-10: Add a caution to not manually close the charge port door.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning

Solo i tecnici che hanno completato tutti i corsi di certificazione richiesti sono autorizzati a eseguire questa procedura. Tesla raccomanda ai tecnici di fornitori di terze parti di seguire una formazione equivalente prima di svolgere la presente procedura. Per maggiori informazioni sui requisiti dei Tecnici Tesla, o per le descrizioni degli argomenti richiesti per i tecnici di fornitori terzi, vedere i Requisiti per certificazioni HV. Ogni volta che si maneggia un raccordo, una barra di distribuzione o un cavo ad alta tensione è necessario indossare idonei dispositivi di protezione individuale (DPI) e guanti isolanti per l'alta tensione con classe di protezione minima 0 (1000 V). Per ulteriori informazioni sulla sicurezza, fare riferimento alle Note tecniche relative ai rischi dell'alta tensione TN-15-92-003, "High Voltage Awareness Care Points".

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning

Togliere tutti i gioielli (orologi, bracciali, anelli, collane, orecchini, medagliette, piercing, ecc.) e tutti gli oggetti (chiavi, monete, penne, matite, strumenti, dispositivi di fissaggio, ecc.) dalle tasche prima di eseguire qualsiasi procedura in presenza di alta tensione.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning

Proper personal protective equipment (PPE) is required to perform this procedure:

  • High voltage insulating gloves
  • Leather glove protectors
  • High voltage glove tester
  • Safety glasses
  • Electrical hazard rated safety shoes
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning

A glove inflator is the only recommended way to test HV gloves. Both HV gloves must pass testing before beginning this procedure. If either glove does not pass the air check, discard the pair.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning

Make sure that the HV gloves are not expired. HV gloves can be used up to 12 months after the testing date printed on the glove, but only 6 months after first use even if the gloves are still within the 12-month period.

Remove

  1. Open all four doors and lower all windows.
  2. Open the trunk.
  3. Apply masking tape around the charge port area.
  4. Open the charge port door.
  5. Move the driver and front passenger seats fully forward.
  6. Remove the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).
  7. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  8. Disconnect 12V/LV power. See 12V/LV Power (Disconnect and Connect).
  9. Perform the charge port voltage check procedure. See .
  10. Remove the trunk garnish. See Garnish - Trunk (Remove and Replace).
  11. Remove the trunk floor trim. See Trim - Floor - Trunk (Remove and Replace).
  12. Remove the trunk sill trim. See Trim - Sill - Trunk (Remove and Replace).
  13. Disconnect the trunk light electrical connector.
  14. Release the clips (x2), and then move the LH trunk side trim aside.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Avoid excessive creasing of the trunk side trim.
  15. Remove the LH taillight. See Taillight - LH (Remove and Install).
  16. Remove the charge port. See .
  17. Disconnect the charge port ECU electrical connector for the charge port door.
  18. Release the charge port door harness grommet from the body.
  19. Release the lower clips (x2) that attach the charge port door to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Release the bottom clips, and then push the bottom of charge port door out.
  20. Gently pull the charge port door away from the body, and then remove the charge port door from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Tabs (x2)
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull the charge port door assembly towards the rear of the vehicle. When the door actuator reaches the rear of the quarter panel, pull the charge port door down to clear the actuator mechanism, and then pull out and away from the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    Manipulation the charge door assembly may be necessary to fully remove the assembly from the vehicle.

Install

  1. Install the charge port door onto the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Clips (x2), tabs (x2)
    Informational PurposesAn informational icon, calling your attention
    Note
    Pivot the charge port door assembly so that the actuator mechanism clears underneath the quarter panel, and then slide the charge door forward toward the rear door.
    Informational PurposesAn informational icon, calling your attention
    Note
    Manipulation of the charge door assembly may be necessary to fully align the assembly to the body.
  2. Secure the charge port door harness grommet to the body.
  3. Connect the charge port ECU electrical connector for the charge port door.
  4. Install the charge port. See .
  5. Install the LH taillight. See Taillight - LH (Remove and Install).
  6. Remove the masking tape around the charge port door.
  7. Europe only: install a CKL charging identifier label (1691926-00-B) on the face plate of the charge port assembly as illustrated, if one was present on the original part.
  8. Move the LH trunk side trim back into position, and then secure it with clips (x2).
  9. Connect the trunk light electrical connector.
  10. Install the trunk sill trim. See Trim - Sill - Trunk (Remove and Replace).
  11. Install the trunk floor trim. See Trim - Floor - Trunk (Remove and Replace).
  12. Install the trunk garnish. See Garnish - Trunk (Remove and Replace).
  13. Reconnect 12V/LV power. See 12V/LV Power (Disconnect and Connect).
  14. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  15. Install the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).
  16. Restore the driver and front passenger seats back to their original position.
  17. Verify the operation of the charging system.
    1. Lightly push on the lower corner of charge power door once to confirm that the door opens.
    2. Confirm vehicle charges by connecting the charge handle to the vehicle.
    3. Disconnect the charge handle and confirm the charge port door closes.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use the customer's charging equipment, if available.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not try to manually close the charge port door.
  18. Raise all windows and close all doors.