2026-06-11

Link - Compliance - Lower - Front - LH (Remove and Replace)

Correction code 31013602 0.36 NOTA: Salvo diversa ed esplicita indicazione nella procedura, il codice modifica e il tempo forfettario, o FRT, riflettono tutto il lavoro richiesto per l'esecuzione di questa procedura, incluse le procedure collegate. Non cumulare i codici modifica a meno che non venga detto esplicitamente di farlo. NOTA: Consultare la Tempistica tariffe fisse per saperne di più sui tempi forfettari e su come essi vengono creati. NOTA: Consultare Protezione personale per assicurarsi di indossare i DPI adatti quando si esegue la procedura descritta di seguito. NOTA: Vedere per le pratiche di lavoro in sicurezza.

  • 2024-01-15: Expanded the installation section since the fasteners' installation order is different from the removal order.
Table 1. Torque Specifications: Link - Compliance - Lower - Front - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Nut that attaches the front LH lower compliance link to the knuckle
180 Nm (132.7 lbs-ft)
  • Torx T40 socket
  • 22 mm socket
  • Combination Wrench 12pt 22mm
 Replace
Bolt and nut that attach the link to the front subframe
115 Nm (84.8 lbs-ft)
  • 21 mm socket
  • 21 mm deep socket
  • Combination Wrench 12pt 21mm
 Reuse

Remove

  1. Remove the LH front wheel. See Wheel Assembly (Remove and Install).
  2. Remove the front aero shield panel. See Panel - Aero Shield - Front (Remove and Replace).
  3. Remove and discard the nut that attaches the front LH lower compliance link to the knuckle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T40 socket
    • 22 mm socket
    • Combination Wrench 12pt 22mm
  4. Remove the bolt and nut that attach the link to the front subframe, and then remove the link from the subframe and knuckle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 21 mm socket
    • 21 mm deep socket
    • Combination Wrench 12pt 21mm

Install

  1. Install the LH front lower compliance link to the front subframe.
  2. Hand-tighten the bolt and nut that attach the link to the front subframe.
  3. Hand-tighten a new nut to attach the front LH lower compliance link to the knuckle, and then torque the nut.
    180 Nm (132.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Counter hold the nut with a T40 socket. Mark with a paint pen.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T40 socket
    • 22 mm socket
    • Combination Wrench 12pt 22mm
  4. Torque the bolt and nut that attach the link to the front subframe.
    115 Nm (84.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Mark with a paint pen.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 21 mm socket
    • 21 mm deep socket
    • Combination Wrench 12pt 21mm
  5. Install the front aero shield panel. See Panel - Aero Shield - Front (Remove and Replace).
  6. Install the LH front wheel. See Wheel Assembly (Remove and Install).