2026-05-12

Glass - Door - LH - Rear (Remove and Replace)

Correction code 11500302 0.36 NOTA: Salvo explicitamente indicado em contrário no procedimento, o código de correção acima e o FRT refletem todo o trabalho necessário para a realização deste procedimento, incluindo os procedimentos associados. Não acumule códigos de correção, salvo se explicitamente instruído. NOTA: Consulte Tempos de taxa fixa para saber mais sobre FRT e sobre a respetiva criação. NOTA: Consulte Proteção pessoal para garantir que utiliza o EPI adequado durante a realização do procedimento abaixo. NOTA: Consulte para conhecer as práticas seguras e saudáveis de trabalho.

  • 2025-05-28: Added new caution to avoid glass damage.
  • 2024-12-10: Added new caution about Pre-Installation Glass Inspection service requirements.
  • 2023-05-24: Added cleaning instructions to prevent glass damage.
Warning IconA warning icon, calling your attention to a possibly risky situation
Aviso
The side impact airbag deployment depends on the rear door sensor's ability to detect a side impact from air pressure. Make sure that there are no uncovered holes in the rear door shells. Additionally, always reinstall plugs or tape when servicing or inspecting the rear doors and their components.
Warning IconA warning icon, calling your attention to a possibly risky situation
CUIDADO
Os novos componentes de vidro (para-brisas, tejadilho, porta e vidro fixo) têm de ser inspecionados antes da instalação, a fim de avaliar se estão em conformidade com as normas internas de qualidade da Tesla. Efetue a inspeção descrita em antes de iniciar este procedimento.
Warning IconA warning icon, calling your attention to a possibly risky situation
CUIDADO
Não feche a porta durante a instalação. O fecho da porta pode danificar o vidro.

Torque Specifications

Tabela 1. Torque Specifications: Glass - Door - LH - Rear (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts that attach the LH rear door glass to the regulator isolator clamps
9.5 Nm (7.0 lbs-ft)
  • 13 mm socket
 Replace 1101805-00-B
Equipamento:
  • 1135305-00-A Tool, Window Switch Bypass, Model 3
  • 1129348-00-A XP-10 Power Supply, XP-10

Remove

  1. Remove the rear LH door trim panel. See Panel - Door Trim - Rear - LH (Remove and Install).
  2. Remove the LH rear door inner belt seal. See #GUID-C30832F9-4546-4EF9-BF17-2DB0DBEC7174.
  3. Remove the plugs that cover the opening in the door for access to the bolts.
  4. Temporarily connect the puddle light to the LH rear door harness.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Route the electrical cable so that it will not be damaged when closing the door.
  5. Connect the window switch special tool and lower the door glass so that the regulator isolator clamp bolts are accessible from the holes.
  6. Remove and discard the bolts that attach the door glass to the regulator isolator clamps, and then remove the door glass from the door.
    Informational PurposesAn informational icon, calling your attention
    Note
    Lift the glass up and then away from the run channel to remove it from the door.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13 mm socket
    Informational PurposesAn informational icon, calling your attention
    Note
    Replace the regulator isolator clamps, if damaged.

Install

  1. Inspect the regulator isolator clamps for glass splinters or other debris, and clean them if necessary.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Debris and splinters may damage or shatter the new door glass.
  2. Position the door glass into the rear door.
  3. Install the new bolts that attach the door glass to the regulator isolator clamps.
    9.5 Nm (7.0 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13 mm socket
  4. Install the inner belt seal to the rear door; attach the inner belt seal with clips.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Press the inner belt seal down into the rear door.
  5. Adjust the door glass. See #GUID-D891CD0C-A189-47FE-A42D-F8461E751119.
  6. Install the rear door trim panel. See Panel - Door Trim - Rear - LH (Remove and Install).
  7. Calibrate the windows. See Window Regulator (Recalibrate).