2026-05-12

Panel - Door Trim - Rear - LH (Remove and Install)

Correction code 15132001 0.12 NOTA: Salvo explicitamente indicado em contrário no procedimento, o código de correção acima e o FRT refletem todo o trabalho necessário para a realização deste procedimento, incluindo os procedimentos associados. Não acumule códigos de correção, salvo se explicitamente instruído. NOTA: Consulte Tempos de taxa fixa para saber mais sobre FRT e sobre a respetiva criação. NOTA: Consulte Proteção pessoal para garantir que utiliza o EPI adequado durante a realização do procedimento abaixo. NOTA: Consulte para conhecer as práticas seguras e saudáveis de trabalho.

  • 2023-07-20: Added a video in step 5 of Remove part.

Torque Specifications

Tabela 1. Torque Specifications: Panel - Door Trim - Rear - LH (Remove and Install)
Description Torque Value Recommended Tools Reuse/Replace Notes
Rear door trim panel to rear door screws
6 Nm (4.4 lbs-ft)
  • Torx T30 socket
 Reuse
Warning IconA warning icon, calling your attention to a possibly risky situation
CUIDADO
Utilize APENAS fixadores com os seguintes n.º de peça:
  • 1488028-00-A ou posterior
  • 1526998-99-A ou posterior

Remove

Warning IconA warning icon, calling your attention to a possibly risky situation
CAUTION
Use only the trim panel screw PN(s) listed in this procedure. See step 12 for more information.
  1. Open the LH rear door, and fully lower the window.
  2. Remove the LH rear door puddle light. See Puddle Light - Rear Door - LH (Remove and Replace).
  3. Release the clip that attaches the screw cover to the front of the LH rear door armrest, and then remove the screw cover from the armrest.
  4. Remove the screws that attach the trim panel to the door.
    6 Nm (4.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T30 socket
  5. Pull out on the trim panel from the puddle light opening to release the clips that attach the trim panel to the door.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not remove the trim panel from the door at this time.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Os vídeos incluídos neste procedimento destinam-se a ser utilizados como uma visão geral apenas para efeitos complementares. Siga todos os passos enumerados no procedimento para evitar danos nos componentes e/ou ferimentos.
    Figure 1. Trim Panel Clip Locations

    Figure 2. Door Clip Locations
  6. Continue to pull and release all of the clips around the edge of the trim panel, working from the bottom up.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not remove the trim panel from the door at this time.
  7. Disconnect the electrical wiring harness from the connectors, and then release the clips that attaches the electrical harness to the trim panel.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not remove the trim panel from the door at this time.
    Figure 3. Trim Panel Connectors
    Figure 4. Door Electrical Harness Connectors
  8. Raise the trim panel up to unhook it from the door, and then remove the panel from the door.
  9. Check the LH rear door for any remaining push clip retainers, and if present, remove them from the door.

Install

  1. Inspect the condition of the LH rear door and the LH rear door trim panel. Replace any broken clips and repair any damage.
  2. Bring the trim panel to the door, and rest it on the door edge.
  3. Fasten the clip that attaches the electrical wiring harness to the trim panel.
  4. Connect the short wire off of the electrical harness to the speaker.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Se o conetor da luz da porta estiver ligado ao altifalante, este sofre danos permanentes e pode provocar derretimento. Não troque o conetor do altifalante da cablagem elétrica pelo conetor da luz da porta.
  5. Connect the electrical harness to the LH rear door trim panel connectors.
  6. Lift the trim panel, compress the LH rear door inner belt seal slightly, and hook the three trim panel tabs into the top edge of the door.
  7. Move the electrical harness connector for the puddle light out the hole in the bottom of the trim panel.
  8. Install the LH rear door puddle light. See Puddle Light - Rear Door - LH (Remove and Replace).
  9. Make sure that the puddle light and map pocket ambient light illuminate when connected.
  10. Fasten the clips that attach the trim panel to the door.
  11. Make sure that the trim panel fits tightly, and that there are no gaps from misaligned or bent clips.
  12. Install the screws that attach the LH rear door trim panel to the LH rear door.
    6 Nm (4.4 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Utilize APENAS fixadores com os seguintes n.º de peça:
    • 1488028-00-A ou posterior
    • 1526998-99-A ou posterior
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Make sure that all fasteners are properly torqued and not cross-threaded.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T30 socket
  13. Install the screw cover to the front of the armrest.
  14. Raise the window and close the door.