2026-07-16

12V/LV Power (Disconnect and Connect)

  • 2025-10-30: Added a caution to make sure windows are not moved for at least 1 minute before disconnecting the 12V/LV power.
  • 2024-01-19: Added info for different Li-Ion battery types.
  • 2023-10-4: Added step to disconnect charge cable in Li-Ion disconnect section.
Correction Codes and FRTs

메모: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오. 메모: 안전하고 건강한 작업 사례는 의 내용을 참조하십시오.

Equipment:
  • 1108272-00-B Cap, Logic Conn, Inv, 3DU (For Original Model 3)
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure disables 12V power, but does not verify that high voltage power is no longer available to high voltage components (PTC heater, A/C compressor, inverters, etc). Perform Vehicle HV Disablement Procedure after this procedure, and before servicing high voltage components.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Failure to follow the exact order of steps in this procedure may cause permanent damage to the car computer.
Warning IconA warning icon, calling your attention to a possibly risky situation
CAUTION
Before disconnecting the 12V/LV power, make sure windows are not moved for at least 1 minute. Failure to wait before disconnecting can result in component damage.

토크 규격

Table 1. 토크 규격: 12V/LV Power (Disconnect and Connect)
설명 토크 값 권장 공구 재사용/교체 참고
(Lead acid) positive/negative cable to the battery terminal
6 Nm (4.4 lbs-ft)
  • 10mm 딥소켓
 재사용

연결 해제 (Original Model 3)

  1. Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning

    Prepare for these conditions before disconnecting 12V power:

    • Closed windows might shatter if the door is opened.

    • Closed doors might cause a lockout condition.

    • Airbags do not deploy.

    • Systems, displays, and other controls are off.

  2. Disconnect any charging cable.
  3. On the touchscreen, power off the climate control system, and wait at least 30 seconds for the climate control system to completely shut down.
  4. Make sure the vehicle is in Park.
  5. 모든 도어를 열고 창문을 내립니다.
  6. LH 및 RH 후면 도어를 열고 작업용 타월을 각 도어 스트라이커를 반쯤 통과시켜 래치가 고정되는 것을 방지합니다.
  7. Remove the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).
  8. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  9. On the touchscreen, touch Controls > Safety > Power Off.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not proceed until the climate control system has been powered off for at least 30 seconds. Do not disconnect 12V power while the climate control system is operational.
  10. Loosen the nut that attaches the 12V battery negative cable to the battery, and then disconnect the cable from the battery.
  11. Set the multimeter to measure DC voltage, and then measure the voltage across the 12V auxiliary battery terminals.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    If the voltage measured is less than 10 volts or greater than 14 Volts, the multimeter is not measuring reliably and must not be used.
  12. If installed, remove the foam cover from the RH side of the ancillary bay.
  13. Disconnect the electrical harness from the high voltage controller connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    The HV battery positive contactor and negative contactor open with a clunk sound.
  14. Install the logic connector cap onto the high voltage controller connector to prevent mistaken reconnection and protect the connector.
  15. Measure the voltage at the LV busbar at the ancillary bay.
    Informational PurposesAn informational icon, calling your attention
    Note
    Measure voltage at the DC passthrough. If the measured voltage is <1V, continue. If the measured voltage is >10V, wait 2 minutes for the 12V/LV system to drain, and then remeasure. If the voltage is still >10V, the LV system is still up;. Escalate for assistance as the PCS is still supporting the Low Voltage system.
  16. If 12V power was disconnected to service a high voltage component, verify that high voltage power is no longer available to that component. See Vehicle HV Disablement Procedure.

연결 해제 (Heat Pump Model 3 with Lead Acid Battery)

  1. Disconnect any charging cable.
  2. On the touchscreen, power off the climate control system, and wait at least 30 seconds for the climate control system to completely shut down.
  3. Make sure the vehicle is in Park.
  4. 모든 도어를 열고 창문을 내립니다.
  5. LH 및 RH 후면 도어를 열고 작업용 타월을 각 도어 스트라이커를 반쯤 통과시켜 래치가 고정되는 것을 방지합니다.
  6. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  7. On the touchscreen, touch Controls > Safety > Power Off.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not proceed until the climate control system has been powered off for at least 30 seconds. Do not disconnect 12V power while the climate control system is operational.
  8. Loosen the nut that attaches the 12V battery negative cable to the battery, and then disconnect the cable from the battery.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Disconnect the 12V battery negative cable before disconnecting the first responder loop.
  9. Locate the first responder loop next to the RH side of the 12V auxiliary battery.
  10. Slide the red locking tab back, press the black tab, and then disconnect the first responder loop.
  11. Set the multimeter to measure DC voltage, and then measure the across the 12V auxiliary battery terminals.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    if the voltage measured is less than 10 volts or greater than 14 Volts, the multimeter is not measuring reliably and must not be used.
  12. If installed, remove the foam cover from the RH side of the ancillary bay.
  13. Disconnect the electrical harness from the high voltage controller connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    The HV battery positive contactor and negative contactor open with a clunk sound.
  14. Install the logic connector cap onto the high voltage controller connector to prevent mistaken reconnection and protect the connector.
  15. Measure the voltage at the LV busbar at the ancillary bay.
    Informational PurposesAn informational icon, calling your attention
    Note
    Measure voltage at the DC passthrough. If the measured voltage is <1V, continue. If the measured voltage is >10V, wait 2 minutes for the 12V/LV system to drain, and then remeasure. If the voltage is still >10V, the LV system is still up;. Escalate for assistance as the PCS is still supporting the Low Voltage system.
  16. If 12V power was disconnected to service a high voltage component, verify that high voltage power is no longer available to that component. See Vehicle HV Disablement Procedure.

연결 해제 (Li-Ion)

  1. Disconnect any charging cable.
  2. 모든 도어를 열고 창문을 내립니다.
  3. LH 및 RH 후면 도어를 열고 작업용 타월을 각 도어 스트라이커를 반쯤 통과시켜 래치가 고정되는 것을 방지합니다.
  4. Power off the vehicle from the center display.
  5. Remove the rear apron. See Underhood Apron - Rear (Remove and Replace).
  6. Disconnect the LV battery connector from the LV battery.
    • Release the green locking tab, pull the black connector lock outwards to release the connector, and then pull up to disconnect the connector.
  7. Disconnect the first responder loop.
    Informational PurposesAn informational icon, calling your attention
    Note
    Before proceeding to service the vehicle, allow 2 minutes for all electrical circuits to discharge.
  8. Set the multimeter to measure voltage, and then measure the across the 12V/LV auxiliary battery terminals.
    Informational PurposesAn informational icon, calling your attention
    Note
    If the voltage across the battery terminals is 0, the battery may have switched off internally. Use a 12V Lead Acid battery for testing. For mobile technicians: use the 12V Lead Acid battery in the Mobile Service vehicle.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    If the voltage across the battery terminals is less than 13 volts or greater than 16 volts, the multimeter is not measuring reliably and must not be used.
  9. If installed, remove the foam cover from the RH side of the ancillary bay.
  10. Disconnect the electrical harness from the high voltage controller connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    The HV battery positive contactor and negative contactor open with a clunk sound.
  11. Install the logic connector cap onto the high voltage controller connector to prevent mistaken reconnection and protect the connector.
  12. Measure the voltage at the LV busbar at the ancillary bay.
    Informational PurposesAn informational icon, calling your attention
    Note
    Measure voltage at the DC passthrough. If the measured voltage is <1V, continue. If the measured voltage is >10V, wait 2 minutes for the 12V/LV system to drain, and then remeasure. If the voltage is still >10V, the LV system is still up;. Escalate for assistance as the PCS is still supporting the Low Voltage system.
  13. If LV power was disconnected to service a high voltage component, verify that high voltage power is no longer available to that component. See Vehicle HV Disablement Procedure.

연결 Original Model 3

  1. Remove the logic connector cap from the high voltage controller connector.
  2. Connect the electrical harness to the high voltage controller connector.
  3. Install the foam cover to the RH side of the ancillary bay.
  4. Install the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).
  5. Connect the 12V battery negative cable to the battery, press down to firmly seat the terminal clamp onto the battery post.
  6. Install the nut that attaches the clamp to the post.
    6 Nm (4.4 lbs-ft)
  7. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  8. Press the brake pedal to turn on vehicle power.
  9. 후면 도어 스트라이커에서 작업용 타월을 치웁니다.
  10. Return the windows, seats, climate control, audio, and charging to the state before service.
  11. Close all doors.

연결 (Heat Pump Model 3 with Lead Acid Battery)

  1. Remove the logic connector cap from the high voltage controller connector.
  2. Connect the electrical harness to the high voltage controller connector.
  3. Install the foam cover to the RH side of the ancillary bay.
  4. Install the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).
  5. Connect the first responder loop, and then slide the red locking tab forward to lock the connector.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not reconnect the 12V negative terminal until the first responder loop is connected.
  6. Connect the 12V battery negative cable to the battery, press down to firmly seat the terminal clamp onto the battery post.
  7. Install the nut that attaches the clamp to the post.
    6 Nm (4.4 lbs-ft)
  8. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  9. Press the brake pedal to turn on vehicle power.
  10. 후면 도어 스트라이커에서 작업용 타월을 치웁니다.
  11. Return the windows, seats, climate control, audio, and charging to the state before service.
  12. Close all doors.

연결 (Li-Ion)

  1. Remove the logic connector cap from the high voltage controller connector.
  2. Connect the electrical harness to the high voltage controller connector.
  3. Install the foam cover to the RH side of the ancillary bay.
  4. Install the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).
  5. Connect the first responder loop.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Connect the first responder loop BEFORE connecting the LV battery connector.
  6. Connect the LV battery connector to the LV battery.
    • Insert the connector, then push the black connector lock inwards to engage the connector, and then seat the green locking tab to secure the connector.
  7. Install the rear apron. See Underhood Apron - Rear (Remove and Replace).
  8. 후면 도어 스트라이커에서 작업용 타월을 치웁니다.
  9. Return the windows, seats, climate control, audio, and charging to the state before service.
  10. Close all doors.