2026-05-12

Handle - Exterior Release - Door - Front - LH (Remove and Replace)

Correction code 11451002 0.60 NOTA: Salvo diversa ed esplicita indicazione nella procedura, il codice modifica e il tempo forfettario, o FRT, riflettono tutto il lavoro richiesto per l'esecuzione di questa procedura, incluse le procedure collegate. Non cumulare i codici modifica a meno che non venga detto esplicitamente di farlo. NOTA: Consultare la Tempistica tariffe fisse per saperne di più sui tempi forfettari e su come essi vengono creati. NOTA: Consultare Protezione personale per assicurarsi di indossare i DPI adatti quando si esegue la procedura descritta di seguito. NOTA: Vedere per le pratiche di lavoro in sicurezza.

  • 2026-01-22: Updated the nuts securing the handle to consumable parts and added the part number.
  • 2025-09-01: Added disconnecting/connecting LV battery power steps, and added the window calibration routine.
Warning IconA warning icon, calling your attention to a possibly risky situation
Avvertenza
The side impact airbag deployment depends on the front door sensor's ability to detect a side impact from air pressure. Make sure that there are no uncovered holes in the front door shells. Additionally, always reinstall plugs or tape when servicing or inspecting the front doors and their components.

Remove

  1. Remove the LH front door trim panel. See .
  2. Remove the LH front door inner belt seal. See .
  3. Remove the front LH door glass. See .
  4. Disconnect the LV battery power. See 12V/LV Power (Disconnect and Connect).
  5. Remove the LH front door closeout panel. See .
  6. Disconnect the electrical wiring harness from the door handle connector.
  7. Remove the plugs that cover access to the door handle nuts.
  8. Remove and discard the nuts that attach the door handle to the door, and then remove the handle from the door.
    Informational PurposesAn informational icon, calling your attention
    Note
    There are 2 versions of these nuts. Replace if the nuts are nyloc nuts. Reuse if the nuts are not.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket

Install

  1. Hand-tighten the new nuts (x3) that attach the door handle to the door.
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not replace the nyloc nuts. Do not stack any more than two shims per mounting stud. According the check result to insert shims between the handle and door inside surface at the handle mounting studs to adjust the gap and flush of the handle if necessary.
  2. Check that the LH front door handle gap and flushness are within specification.
    Informational PurposesAn informational icon, calling your attention
    Note
    See
  3. Torque the nuts (x3) that attach the door handle to the door.
    7 Nm (5.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  4. Install the plugs that cover access to the door handle nuts.
  5. Connect the electrical wiring harness to the door handle connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    Fully seat the connector, and then engage the locking tab.
  6. Install the LH front door closeout panel. See .
  7. Connect the LV battery power. See 12V/LV Power (Disconnect and Connect).
  8. Install the front LH door glass. See .
  9. Install the LH front door inner belt seal. See .
  10. Install the LH front door trim panel. See .
  11. Place the vehicle in Service Mode by using the touchscreen. See .
  12. Unlock the vehicle gateway. See .
  13. Close the LH front door.
  14. On the touchscreen, tap the Service Mode "wrench" (at the bottom of the touchscreen UI), and then tap Closures > Windows > Calibrate Windows > Run, and allow the routine to complete.
  15. Exit Service Mode. See .