2026-05-12

Center Console (Remove and Install)

Correction code 15190101 0.42 NOTA: Salvo diversa ed esplicita indicazione nella procedura, il codice modifica e il tempo forfettario, o FRT, riflettono tutto il lavoro richiesto per l'esecuzione di questa procedura, incluse le procedure collegate. Non cumulare i codici modifica a meno che non venga detto esplicitamente di farlo. NOTA: Consultare la Tempistica tariffe fisse per saperne di più sui tempi forfettari e su come essi vengono creati. NOTA: Consultare Protezione personale per assicurarsi di indossare i DPI adatti quando si esegue la procedura descritta di seguito. NOTA: Vedere per le pratiche di lavoro in sicurezza.

Torque Specifications

Tabella 1. Torque Specifications: Center Console (Remove and Install)
Description Torque Value Recommended Tools Reuse/Replace Notes
Center console side and rear corner to body bolts
7 Nm (5.2 lbs-ft)
  • 10 mm socket
 Reuse
Inner front center console to body screws
1.7 Nm (1.3 lbs-ft)
  • Torx T20 socket
  • Wiha TorqueVario-S 0.8 Nm - 2.0 Nm screwdriver (installation only)
 Reuse

Remove

  1. Open all the doors and lower all the windows.
  2. Move the driver seat rearward.
  3. Remove and attach the customer's belongings from the center console, if needed.
  4. Remove the phone tray. See #GUID-3F23F126-C4A4-4605-9609-DAB4AF0EF784.
  5. Remove the bolts that attach the front of the center console to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Torx T20 socket
    • Wiha TorqueVario-S 0.8 Nm - 2.0 Nm screwdriver (installation only)
  6. Close the front and rear console rotating lids.
  7. Remove the driver floormat.
  8. Remove the LH center console side panel carpet. See Side Panel - Center Console - LH (Remove and Replace).
  9. Remove the bolts that attach the LH front of the center console to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 10 mm socket
  10. Move the driver seat forward.
  11. Move the front passenger seat forward.
  12. Remove the center console lower rear panel. See Panel - Lower Rear - Center Console (Remove and Replace).
  13. Remove the bolt that attaches the LH rear of the center console to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 10 mm socket
  14. Remove the bolt that attaches the RH rear of the center console to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 10 mm socket
  15. Move the front passenger seat rearward.
  16. Remove the front passenger floormat.
  17. Remove the RH center console side panel carpet. See Side Panel - Center Console - LH (Remove and Replace).
  18. Remove the bolts that attach the RH front of the center console to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 10 mm socket
  19. Disconnect the electrical connector that is located at the RH front of the center console.
  20. Disconnect the electrical connector from the rear of the center console.
  21. With an assistant, remove the center console from the vehicle as follows:
    1. Tilt the rear of the center console upwards.
    2. Pull the center console towards the rear of the vehicle.
    3. Tilt the front of the center console upwards.
    4. Remove the center console through the passenger front door.

Install

  1. With an assistant, install the center console into the vehicle as follows:
    1. Tilt the front of the center console downwards.
    2. Slide the center console towards the front of the vehicle.
    3. Tilt the rear of the center console downwards until it is in place.
  2. Connect the electrical connector in the rear of the center console.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Ensure the connector is properly installed. Perform a push-pull test before continuing this procedure.
  3. Install the bolt that attaches the RH rear of the center console to the body.
    7 Nm (5.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 10 mm socket
  4. Install the bolt that attaches the LH rear of the center console to the body.
    7 Nm (5.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 10 mm socket
  5. Install the center console lower rear panel. See Panel - Lower Rear - Center Console (Remove and Replace).
  6. Move the front passenger seat rearward.
  7. Install the bolts that attach the RH front of the center console to the body.
    7 Nm (5.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 10 mm socket
  8. Connect the electrical connector that is located at the RH front of the center console.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Ensure the connector is properly installed. Perform a push-pull test before continuing this procedure.
  9. Install the RH center console side panel carpet. See Side Panel - Center Console - LH (Remove and Replace).
  10. Install the front passenger floormat.
  11. Move the front passenger seat to the orignal position.
  12. Move the driver seat rearward.
  13. Install the bolts that attach the LH front of the center console to the body.
    7 Nm (5.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 10 mm socket
  14. Install the LH center console side panel carpet. See Side Panel - Center Console - LH (Remove and Replace).
  15. Install the driver floormat.
  16. Open the center console rotating lid.
  17. Install the bolts that attach the front of the center console to the body.
    1.7 Nm (1.3 lbs-ft)
    • Torx T20 socket
    • Wiha TorqueVario-S 0.8 Nm - 2.0 Nm screwdriver (installation only)
  18. Install the phone tray. See #GUID-3F23F126-C4A4-4605-9609-DAB4AF0EF784.
  19. Move the driver seat to the original position.
  20. Restore the customer's belongings into the center console, if needed.
  21. Raise all the windows and close all the doors.