2026-05-12

Fender Support - Front - LH (Remove and Replace)

Correction code 10101032 0.84 NOTA: Salvo diversa ed esplicita indicazione nella procedura, il codice modifica e il tempo forfettario, o FRT, riflettono tutto il lavoro richiesto per l'esecuzione di questa procedura, incluse le procedure collegate. Non cumulare i codici modifica a meno che non venga detto esplicitamente di farlo. NOTA: Consultare la Tempistica tariffe fisse per saperne di più sui tempi forfettari e su come essi vengono creati. NOTA: Consultare Protezione personale per assicurarsi di indossare i DPI adatti quando si esegue la procedura descritta di seguito. NOTA: Vedere per le pratiche di lavoro in sicurezza.

Torque Specifications

Tabella 1. Torque Specifications: Fender Support - Front - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolt that attaches the LH front fender support to the front end carrier
16 Nm (11.8 lbs-ft)
  • 13 mm socket
 Reuse
Bolt that attaches the LH front fender support to the front fender assembly
9.8 Nm (7.2 lbs-ft)
  • 10 mm socket
 Reuse
Bolts (x3) that attach the LH front fender support to the vehicle
35 Nm (25.8 lbs-ft)
  • 10 mm socket
 Reuse

Remove

  1. Disconnect 12V power. See 12V/LV Power (Disconnect and Connect).
  2. Remove the front fascia. See Fascia - Front (Remove and Install).
  3. Disconnect the LH headlamp connector.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Avvertenza
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling to release the connector.
  4. Remove the front harness clips (x2) around the LH headlamp area.
  5. Disconnect the LH front wheel speed sensor connector.
  6. Disconnect the LH front ride height sensor connector.
  7. Remove the front harness clips (x3) around the LH front wheel liner area.
    Informational PurposesAn informational icon, calling your attention
    Nota
    American region vehicles have 2 clips.
  8. Remove the clips (x3) that attach the front harness to the LH crush can.
  9. Disconnect the front harness from the LH acceleration sensor.
  10. Disconnect the connectors (x2) from the horn assembly.
    Informational PurposesAn informational icon, calling your attention
    Nota
    The horn is located on the LH front area of the vehicle.
  11. Disconnect the front harness connector for the LH front carrier harness.
  12. Disconnect the cooling fan module connector.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Avvertenza
    Disconnect the connector after the coolant hose is capped to avoid the coolant damaging the connector.
  13. Remove the harness from the LH front fender support.
  14. Remove the bolt that attaches the LH front fender support to the front end carrier.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13 mm socket
  15. Remove the bolt that attaches the LH front fender support to the front fender assembly.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  16. Remove the bolts (x3) that attach the LH front fender support to the vehicle, and then remove the LH front fender support from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket

Install

  1. Install the bolts (x3) that attach the LH front fender support to the vehicle.
    35 Nm (25.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  2. Install the bolt that attaches the LH front fender support to the front fender assembly.
    9.8 Nm (7.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  3. Install the bolt that attaches the LH front fender support to the front end carrier.
    16 Nm (11.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13 mm socket
  4. Route the front harness through the LH fender support, and secure the harness to the fender support.
  5. Connect the LH front ride height sensor connector.
  6. Connect the LH front wheel speed sensor connector.
  7. Install the front harness clips (x3) around the LH front wheel liner area.
    Informational PurposesAn informational icon, calling your attention
    Nota
    American region vehicles have 2 clips.
  8. Install the clips (x3) that attach the front harness to the LH crush can.
  9. Connect the front harness from the LH acceleration sensor.
  10. Connect the connectors (x2) to the horn assembly.
  11. Connect the front harness connector for the LH front carrier harness.
  12. Connect the cooling fan module connector.
  13. Install the front harness clips (x2) around the LH headlamp area.
  14. Connect the LH headlamp connector.
  15. Install the front fascia. See Fascia - Front (Remove and Install).
  16. Connect 12V power. See 12V/LV Power (Disconnect and Connect).