2026-05-22

Fascia - Rear (Remove and Install)

Correction code 10013001 0.54 NOTA: Salvo diversa ed esplicita indicazione nella procedura, il codice modifica e il tempo forfettario, o FRT, riflettono tutto il lavoro richiesto per l'esecuzione di questa procedura, incluse le procedure collegate. Non cumulare i codici modifica a meno che non venga detto esplicitamente di farlo. NOTA: Consultare la Tempistica tariffe fisse per saperne di più sui tempi forfettari e su come essi vengono creati. NOTA: Consultare Protezione personale per assicurarsi di indossare i DPI adatti quando si esegue la procedura descritta di seguito. NOTA: Vedere per le pratiche di lavoro in sicurezza.

  • 2023-04-18: Added steps to remove/install fascia to rear quarter panel U-nuts.
  • 2023-07-06: Added videos in step 6 of Remove part and step 5 of Install part.

Torque Specifications

Table 1. Torque Specifications: Fascia - Rear (Remove and Install)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolt that attaches the corner of the rear fascia to the body
4 Nm (2.9 lbs-ft)
  • 10 mm hex
 Reuse
Bolt that attaches the fascia to the rear quarter panel
2 Nm (1.5 lbs-ft)
  • Torx T25 socket
 Reuse
Bolts that attach the rear portion of the mid aero shield
5 Nm (3.7 lbs-ft)
  • 10 mm hex
 Reuse
Bolts that attach the rear diffuser to the body
4 Nm (2.9 lbs-ft)
  • 10 mm hex
 Reuse

Remove

  1. Move the vehicle to a 2 post lift. See Raise Vehicle - 2 Post Lift.
  2. Remove the LH taillight. See Taillight - LH (Remove and Install).
  3. Remove the bolt that attaches the LH side of the rear fascia to the outer LH rear quarter panel.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm hex
  4. Release the clips (x3) and remove the push nut that attach the rear portion of the LH rear wheel arch liner to the body.
  5. Remove the bolt that attaches the LH side of the rear fascia to the inner LH rear quarter panel.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T25 socket
  6. Without pulling back the rear fascia, reach behind the fascia to remove the U-nut that attaches the LH rear fascia to the LH rear quarter panel.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not pull back on the rear fascia while the u-nut is still installed, as this can scratch the rear quarter panel.
  7. Repeat step 2 through step 6 on the RH side of the vehicle.
  8. Remove the bolts (x5) that attach the rear portion of the mid aero shield panel to the rear subframe.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm hex
  9. Remove the bolts (x5) that attach the rear diffuser to the body.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm hex
  10. Repeat the previous step on the RH side of the vehicle.
  11. Disconnect the rear fascia electrical harness.
  12. With the help of an assistant, remove the rear fascia from the vehicle.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Carefully remove the rear fascia from the body to help prevent damage to the rear quarter panels.

Install

  1. With the help of an assistant, install the rear fascia onto the vehicle.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Carefully install the rear fascia to the body to help prevent damage the rear quarter panels.
  2. Connect the rear fascia electrical harness.
  3. Install the bolts (x5) that attach the rear diffuser to the body.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm hex
  4. Apply a thin bead of threadlocker to the threads of the bolts that attach the mid aero shield panel to the vehicle.
  5. Install the bolts (x5) that attach the rear portion of the mid aero shield panel to the rear subframe.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm hex
  6. Install the u-nut that attaches the rear fascia to the LH rear quarter panel, and then install the bolt that attaches the LH side of the rear fascia to the inner LH rear quarter panel.
    2 Nm (1.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T25 socket
  7. Fasten the clips (x3) and install the push nut that attach the rear portion of the LH rear wheel arch liner to the body.
  8. Install the bolt that attaches the LH side of the rear fascia to the outer LH rear quarter panel.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm hex
  9. Install the LH taillight. See Taillight - LH (Remove and Install).
  10. Repeat step 6 through step 9 on the RH side of the vehicle.
  11. Remove the vehicle from the 2 post lift. See Raise Vehicle - 2 Post Lift.