2026-05-12

Bracket - Compressor (Heat Pump) (Remove and Replace)

Correction code 18203212 0.42 NOTA: Salvo diversa ed esplicita indicazione nella procedura, il codice modifica e il tempo forfettario, o FRT, riflettono tutto il lavoro richiesto per l'esecuzione di questa procedura, incluse le procedure collegate. Non cumulare i codici modifica a meno che non venga detto esplicitamente di farlo. NOTA: Consultare la Tempistica tariffe fisse per saperne di più sui tempi forfettari e su come essi vengono creati. NOTA: Consultare Protezione personale per assicurarsi di indossare i DPI adatti quando si esegue la procedura descritta di seguito. NOTA: Vedere per le pratiche di lavoro in sicurezza.

Torque Specifications

Tabella 1. Torque Specifications: Bracket - Compressor (Heat Pump) (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolt that attaches the ground strap to the A/C compressor
7 Nm (5.2 lbs-ft)
  • Torx T25 socket
 Reuse
Bolts that attach the A/C compressor assembly to the strut tower brace
31 Nm (22.9 lbs-ft)
  • 10 mm deep socket
 Reuse
Bolts that attach the A/C compressor bracket to the A/C compressor
9 Nm (6.6 lbs-ft)
  • 10 mm deep socket
 Reuse

Remove

  1. Remove the underhood storage unit. See #GUID-4FBD5199-27DF-4D9D-A193-1901CE127862.
  2. Disconnect 12V power. See 12V/LV Power (Disconnect and Connect).
  3. Remove the 12V auxiliary battery. See .
  4. Remove the rear battery tie down strap from the 12V battery bracket.
    Informational PurposesAn informational icon, calling your attention
    Nota
    The 12V battery bracket also functions as the A/C compressor bracket.
  5. Release the clip that attaches the 12V battery vent tube to the 12V battery bracket.
  6. Release the clips (x2) that attach the coolant hose to the 12V battery bracket.
  7. Release the retaining clips that attach the A/C compressor HV harness to the shock tower support brace.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Avvertenza
    Pull upward on the clip to assist with removal. Do not pull upward on the HV cable.
  8. Release the connector locking tab, and then disconnect the HVIL connector near the LH front strut tower.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Avvertenza
    NON premere sulla linguetta di blocco rossa. Tirare la linguetta allontanandola dal connettore fino a sbloccarlo, quindi continuare a tirare il corpo principale del connettore per scollegarlo completamente.
  9. Release the connector locking tab, and then disconnect the A/C compressor logic electrical connector from the A/C compressor.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Avvertenza
    NON premere sulla linguetta di blocco rossa. Tirare la linguetta allontanandola dal connettore fino a sbloccarlo, quindi continuare a tirare il corpo principale del connettore per scollegarlo completamente.
  10. Release the clip that attaches the A/C compressor logic harness to the A/C compressor HV harness bracket.
  11. Remove the bolt that attaches the ground strap to the A/C compressor, and then set the ground strap aside.
    7 Nm (5.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T25 socket
  12. Release the clip that attaches the coolant hose to the A/C compressor bracket, near the ground strap attachment point.
  13. Move the HV harness bracket forward and up to release the bracket from the A/C compressor, and then carefully set the bracket aside.
  14. With an assistant, remove the bolts that attach the A/C compressor assembly to the strut tower brace, and then carefully maneuver the assembly towards the front of the vehicle, under the strut tower support brace. Rest the A/C compressor assembly on the front underhood storage unit reinforcement beam.
    31 Nm (22.9 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Avvertenza
    Do not rest the A/C compressor on the HV connector.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm deep socket
  15. With an assistant, remove the bolts that attach the A/C compressor bracket to the A/C compressor, and then remove the bracket from the compressor.
    9 Nm (6.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm deep socket

Install

  1. Position the A/C compressor bracket on the A/C compressor, and then install the bolts (x3) that attach the bracket to the compressor.
    9 Nm (6.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm deep socket
  2. Using a blow gun, clean the bolt holes that are used to attach the A/C compressor bracket to the front strut tower support brace.
  3. With an assistant supporting the A/C compressor assembly under the strut tower brace, hand-start the bolts that attach the A/C compressor assembly to the brace, and then torque the bolts.
    31 Nm (22.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm deep socket
  4. Install the clip that attaches the coolant hose to the A/C compressor bracket, near the ground strap attachment point.
  5. Position the ground strap on the A/C compressor, and then install the bolt that attaches the ground strap to the A/C compressor.
    7 Nm (5.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T25 socket
  6. Install the clip that attaches the A/C compressor low voltage harness to the A/C compressor HV harness bracket.
  7. Connect the low voltage electrical connector to the A/C compressor, and then engage the locking tab.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Avvertenza
    Premere la linguetta di blocco rossa verso il connettore per inserire il meccanismo di blocco. NON premere in basso o tirare verso l'alto la linguetta di blocco rossa.
  8. Connect the HVIL connector near the LH front strut tower, and then engage the locking tab.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Avvertenza
    Premere la linguetta di blocco rossa verso il connettore per inserire il meccanismo di blocco. NON premere in basso o tirare verso l'alto la linguetta di blocco rossa.
  9. Install the clips that attach the A/C compressor HV harness to the strut tower support brace.
  10. Install the clips (x2) that attach the coolant hose to the A/C compressor bracket.
  11. Install the rear battery tie down strap on the 12V battery bracket.
  12. Install the clip that attaches the 12V battery vent tube to the 12V battery bracket.
  13. Install the 12V auxiliary battery. See .
  14. Reconnect 12V power. See 12V/LV Power (Disconnect and Connect).
  15. Install the underhood storage unit. See .
  16. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).