2026-07-09

Glass - Backlight (Heat Pump) (Remove and Install)

교정 코드 10204111 1.26 메모: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오. 메모: 안전하고 건강한 작업 사례는 의 내용을 참조하십시오.

Warning IconA warning icon, calling your attention to a possibly risky situation
CAUTION
유럽만 해당: 디이소시아네이트 작업에 대한 훈련을 받고 모든 필수 인증 과정을 완료한 기술자만이 우레탄 및 디이소시아네이트가 포함된 기타 제품을 사용하는 절차를 수행할 수 있습니다. 디이소시아네이트가 함유된 제품으로 작업할 때는 적절한 개인 보호 장비(PPE)를 착용해야 합니다.

탈거

  1. Open all doors and lower the windows.
    Informational PurposesAn informational icon, calling your attention
    Note
    Latch the rear doors to prevent accidental closure.
  2. Move the front seats fully forward.
  3. Release the clips that attach the LH upper B-pillar trim to the B-pillar, and then move the trim aside.
  4. Remove the LH side rail trim. See #GUID-F7357289-0632-4B38-A804-58B999076AE1.
  5. Release the clip that attach the screw covers to the LH rear coat hook.
  6. Remove the screw that attach the LH rear coat hook to the body.
  7. Repeat step 3 through step 6 for the RH side of the vehicle.
  8. Release clips (x4) that attach the rear end of the headliner to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    If necessary, use an air bladder between the headliner and body for additional clearance.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Be cautious not to damage the headliner.
  9. Remove the LH 2nd row seat side bolster. See Bolster - Side - Seat - 2nd Row - LH (Remove and Replace).
  10. Remove the LH upper C-pillar trim. See #GUID-CA7062E0-67B6-4F6E-8E04-41149EBDB913.
  11. Release the clip and tabs that attach the LH rear C-pillar trim to the body, and then set the trim aside.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull the rear of the trim forward, and then upward to remove it.
  12. Disconnect the electrical connector from the FM antenna amplifier.
  13. Disconnect the backlight electrical harness connector from the antenna amplifier on the LH side C-pillar.
  14. Disconnect the ground noise filter antenna connector on the LH side of the vehicle.
  15. Release the LH side backlight busbar harness from the body.
  16. Remove the RH 2nd row seat side bolster. See Bolster - Side - Seat - 2nd Row - LH (Remove and Replace).
  17. Remove the RH upper C-pillar trim. See #GUID-CA7062E0-67B6-4F6E-8E04-41149EBDB913.
  18. Release the clip and tabs that attach the RH rear C-pillar trim to the body, and then set the trim aside.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull the rear of the trim forward, and then upward to remove it.
    Figure 1. LH shown; RH similar
  19. Disconnect the 12V noise filter antenna connector on the RH side of the vehicle.
  20. Release the RH side backlight busbar harness from the body.
  21. Disconnect the backlight electrical harness connector from the tuner on the RH C-pillar.
  22. Remove the package tray trim. See Trim - Package Tray (Remove and Replace).
  23. Use masking tape to tape the backlight glass antenna connectors to the backlight glass.
  24. Use the exterior switch to open the trunk.
  25. Apply masking tape to the exterior of the LH and RH roof pillars to protect the paint from damage.
  26. Cut a suitable length of square wire to use with T-handles.
  27. Secure the wire to the starter tool and push the tool through the urethane at the lower side of the RH C-pillar.
  28. Remove the wire from the starter tool and remove the tool from the urethane.
  29. Secure each end of the wire with a T-handle.
  30. With an assistant, use the T-handles to cut the urethane that attaches the backlight glass to the body. Cut in a counter-clockwise motion over the top of the backlight glass to the lower side of the LH C-pillar. Return to the starting point in a clockwise motion and continue past the bottom of the backlight glass to the lower side of the LH C-pillar.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Use caution when working around the headliner area.
  31. Cut the square wire and remove the T-handles.
  32. Attach suction cups to the LH and RH sides of the backlight glass.
  33. With an assistant, remove the backlight glass from the vehicle.
  34. Use a scraper to carefully remove the old urethane from the body.
  35. Use an IPA wipe to clean the urethane path on the vehicle. Allow 1 minute for the IPA to dry.
  36. Use a scraper to carefully remove the old seal from the backlight glass.
  37. Use a scraper to remove the old urethane from the backlight glass.
  38. Use an IPA wipe to clean the surface of the backlight glass. Allow 1 minute for the IPA to dry.

장착

  1. Peel the adhesive backing off the new seal at the corner and slowly apply the adhesive backing to the adhesive path on the backlight glass.
    Informational PurposesAn informational icon, calling your attention
    Note
    Firmly press the seal onto the glass during installation. Ensure the adhesive is installed as close to the edge of the glass as possible.
  2. Peel the adhesive backing off at the end of the new trunk flip seal, and then slowly apply the seal to the old adhesive path on the backlight glass.
    Informational PurposesAn informational icon, calling your attention
    Note
    Start by installing the trunk flip seal where the backlight glass seal ends. Firmly press the seal onto the glass during installation. Ensure the adhesive is installed as close to the edge of the glass as possible.
    Informational PurposesAn informational icon, calling your attention
    Note
    There will be overlap at the end of the seal. Cutting the seal is in the next step.
  3. Cut the trunk flip seal overlap.
  4. Install the new net pads onto the backlight glass.
    Informational PurposesAn informational icon, calling your attention
    Note
    Figure 2. Side Net Pads
    Figure 3. Upper Net Pads
    Figure 4. Rear Net Pads
  5. Verify the suction handles are secured to the backlight glass.
  6. With an assistant, position the backlight glass onto the vehicle for a dry fit and note any locations where the net pads need to be adjusted.
  7. If necessary, perform net pad adjustment.
    1. Cut teflon tape into rectangles having dimensions 5mm x 20mm.
    2. With an assistant, remove the backlight glass and set it on a stand.
    3. Apply the teflon tape rectangles to the net pads where adjustment is needed.
      Informational PurposesAn informational icon, calling your attention
      Note
      Make sure that the edges of the tape rectangles align with the edges of the net pads.
    4. With an assistant, position the backlight glass onto the vehicle and check the net pads fitment.
    5. Repeat step #GUID-62BA0B0B-5667-4E7A-9377-FD16DF5909D4__GUID-49C91840-AA81-48F5-828D-99AB7ACAA5C5 through step #GUID-62BA0B0B-5667-4E7A-9377-FD16DF5909D4__GUID-DF486E46-037A-42B4-92FC-BA81EFDFB3D7 to adjust the net pads.
  8. With an assistant, remove the backlight glass and set it on a stand.
  9. Apply urethane primer:
    1. Apply urethane primer to the vehicle along the urethane path and in areas that were damaged during removal of the backlight glass.
    2. Apply urethane primer to the backlight glass along the urethane path.
    Informational PurposesAn informational icon, calling your attention
    Note
    Allow the primer to dry for at least 2 minutes before continuing.
  10. Apply urethane to the body following the original path.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure that the urethane bead has a triangular cross-section of approximate width 8 mm and height 13 mm.
  11. With an assistant, install the backlight glass to the vehicle.
  12. Check the gap and flush of the backlight glass to the body before fully seating the backlight glass.
  13. Remove the masking tape from the exterior C-pillars.
  14. Close the trunk.
  15. Fully seat the backlight glass, check the gap and flush, and adjust as necessary.
  16. Use an IPA wipe to clean any debris or visible urethane from the backlight glass and body.
  17. Apply masking tape to attach the backlight glass to the body while the urethane cures.
    Informational PurposesAn informational icon, calling your attention
    Note
    For urethane curing time, follow urethane manufacturer's recommendations.
  18. Remove the suction cups from the backlight glass.
  19. Install the read end of the headliner to the body.
  20. Install the screws that attach the LH coat hook to the body.
    2.5 Nm (1.8 lbs-ft)
  21. Fasten the clips that attach the screw cover to the LH rear coat hook, and then push the coat hook to close.
  22. Install the clips that attach the LH upper B-pillar trim to the B-pillar.
  23. Repeat step 20 through step 22 for the RH side of the vehicle.
  24. Install the package tray trim. See Trim - Package Tray (Remove and Replace).
  25. Connect the backlight electrical harness connector to the tuner on the RH C-pillar.
  26. Attach the RH side backlight busbar harness to the body.
  27. Connect the 12V noise filter antenna connector on the RH side of the vehicle.
  28. Install the clip and tabs that attach the RH rear C-pillar trim to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull the rear of the trim forward, and then upward to remove it.
  29. Install the RH upper C-pillar trim. See .
  30. Install the RH side rail trim. see .
  31. Install the RH 2nd row seat side bolster. See Bolster - Side - Seat - 2nd Row - LH (Remove and Replace).
  32. Attach the LH side backlight busbar harness to the body.
  33. Connect the ground noise filter antenna connector on the LH side of the vehicle.
  34. Connect the backlight harness connector to the antenna amplifier.
  35. Connect the electrical connector to the FM antenna amplifier.
  36. Install the clip and tabs that attach the LH rear C-pillar trim to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull the rear of the trim forward, and then upward to remove it.
  37. Install the LH upper C-pillar trim. See .
  38. Install the LH side rail trim. see .
  39. Install the LH 2nd row seat side bolster. See Bolster - Side - Seat - 2nd Row - LH (Remove and Replace).
  40. Return the front seats to the original position.
  41. Connect a laptop with Toolbox 3.0 to the vehicle.
  42. Select the 'Actions/Autodiag' tab and search for 'VCRIGHT'.
  43. Select TEST-RESET_VCRIGHTvia Service Mode Plus:
    • Low Voltage ➜ Power Distribution ➜ Reset VCRIGHT
    • Mid Voltage ➜ Power Distribution ➜ Reset VCRIGHT
    via Toolbox:(link)    , click Run and allow the routine to complete.
  44. Disconnect the laptop from the vehicle.
  45. Raise all windows and close all doors.
  46. Remove the masking tape after the urethane has cured.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    접착제 제조사가 권장하는 최소 주행 재개 가능 시간이 경과할 때까지 차량을 주행하지 마십시오. Dow Betaseal Express의 주행 재개 가능 시간은 -18˚C(0˚F) 이상의 온도에서 1시간 이상입니다. 필요한 경우, 테이프를 차량 글라스에 부착한 상태로 두고 24 시간 후에는 테이프를 제거할 수 있다고 고객에게 알려주십시오. 또한 고객에게 다음 24시간 동안 고속 주행과 과속 방지턱 통과를 피해야 한다고 조언하십시오.