2026-05-04

펜더 어셈블리 - 전면 - LH(탈거 및 장착)

교정 코드 101030010.90 메모: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오. 메모: 안전하고 건강한 작업 사례는 의 내용을 참조하십시오.

    This procedure assumes the cowl screen carrier bracket, headlight grommet, and underhood storage unit clips on the fender assembly being replaced are undamaged. Inspect these components and if necessary, replace with new parts.

    탈거

    1. Raise and support the vehicle. See 차량 올리기 - 2 포스트 리프트.
    2. Remove the rear underhood apron. See 후드 내 에이프런 - 후면(탈거 및 교체).
    3. Remove the cabin intake duct. See 덕트 - 상단 - 실내 흡기(탈거 및 교체).
    4. Remove the hood latch cover. See 커버 - 후드 래치(탈거 및 교체).
    5. Remove the underhood storage unit. See .
    6. Remove the LH shock tower cover. See 커버 - 쇼크 타워 - LH(탈거 및 교체).
    7. Remove the front wheels. See 휠 어셈블리(탈거 및 장착).
    8. Remove the front aero shield panel. See 패널 - 에어로 실드 - 전면(탈거 및 교체).
    9. Remove the front fascia. See 페시아 - 전면(탈거 및 장착).
    10. Remove the LH headlight. See .
    11. Disconnect the electrical connectors (2x) from the front side repeater light.
    12. Release the two leftmost clips on the cowl screen panel from the LH front fender bracket.
    13. Remove the bolts that attach the upper LH front fender to the vehicle.
    14. Remove the bolt that attaches the lower LH front fender to the vehicle.
    15. Remove the bolt that attaches the rear LH front fender to the vehicle.
    16. Remove the bolt and nut that attach the lower LH front fender to the vehicle.
    17. Inspect the area between the upper LH front fender and the vehicle body for foam sealant. If present, carefully cut the sealant with a blade, and then separate the upper fender from the body with a plastic trim tool.
    18. Remove the LH front fender from the vehicle.
    19. Use a flat scraper blade and isopropyl alcohol (IPA) to remove the foam sealant from the LH outer shotgun panel. Any remaining sealant should be flush with the shotgun panel.
    20. Apply primer to the LH outer shotgun panel, completely covering the previous foam application area.

    장착

    Informational PurposesAn informational icon, calling your attention
    TIp
    For instructions on how to align the fender, refer to .
    1. Load urethane into a caulking gun, and then cut an opening that is 3.5 mm wide and 1.5 mm tall.
    2. Apply a dollop of urethane on top of the primed surface of the LH outer shotgun panel.
    3. Position the LH front fender on the vehicle.
    4. Install the bolt and nut that attach the lower LH front fender to the vehicle.
      9.8 Nm (7.2 lbs-ft)
      9.8 Nm (7.2 lbs-ft)
    5. Install the bolt that attaches the rear LH front fender to the vehicle.
      9.8 Nm (7.2 lbs-ft)
    6. Install the bolt that attaches the lower LH front fender to the vehicle.
      9.8 Nm (7.2 lbs-ft)
    7. Install the bolts that attach the upper LH front fender to the vehicle.
      9.8 Nm (7.2 lbs-ft)
    8. Install the cowl screen panel clips (2x) on the LH front fender bracket.
    9. Connect the electrical connectors (2x) to the front side repeater light.
    10. Install the LH headlight. See .
    11. Install the front fascia. See 페시아 - 전면(탈거 및 장착).
    12. Install the front aero shield panel. See 패널 - 에어로 실드 - 전면(탈거 및 교체).
    13. Install the front wheels. See 휠 어셈블리(탈거 및 장착).
    14. Install the LH shock tower cover. See 커버 - 쇼크 타워 - LH(탈거 및 교체).
    15. For China, Japan and Korea only: Install a new motor ID label on the fender.
    16. Install the underhood storage unit. See .
    17. Install the hood latch cover. See 커버 - 후드 래치(탈거 및 교체).
    18. Install the cabin intake duct. See 덕트 - 상단 - 실내 흡기(탈거 및 교체).
    19. Install the rear underhood apron. See 후드 내 에이프런 - 후면(탈거 및 교체).
    20. Remove the vehicle from the lift.