2026-05-12

Brake Caliper - Rear - LH (Remove and Replace)

Correction code 33010502 0.60 NOTA: Salvo diversa ed esplicita indicazione nella procedura, il codice modifica e il tempo forfettario, o FRT, riflettono tutto il lavoro richiesto per l'esecuzione di questa procedura, incluse le procedure collegate. Non cumulare i codici modifica a meno che non venga detto esplicitamente di farlo. NOTA: Consultare la Tempistica tariffe fisse per saperne di più sui tempi forfettari e su come essi vengono creati. NOTA: Consultare Protezione personale per assicurarsi di indossare i DPI adatti quando si esegue la procedura descritta di seguito. NOTA: Vedere per le pratiche di lavoro in sicurezza.

  • 2026-02-19: Added a warning.
  • 2025-05-22: Removed unnecessary step.
  • 2024-05-28: Updated EPB Service Mode reference.
  • 2023-06-23: Removed steps to update epbxHwType configuration.
  • 2023-03-28: Added steps to update epbxHwType configuration.
Apparecchiatura:
  • 1134520-00-A Kit, EPB Release, Handheld
  • 1129348-00-A XP-10 Power Supply, XP-10
Warning IconA warning icon, calling your attention to a possibly risky situation
Avvertenza
Al momento dell'installazione, assicurarsi che il tubo flessibile del freno non sia attorcigliato e che possa piegarsi in avanti. Il tubo flessibile del freno non deve essere a contatto con il rivestimento del passaruota quando il veicolo viene abbassato.
Informational PurposesAn informational icon, calling your attention
Nota
This procedure is applicable to both Performance and non-Performance rear brakes.
Warning IconA warning icon, calling your attention to a possibly risky situation
Avvertenza
Il liquido dei freni scioglie la vernice. Tenere a portata di mano dei panni puliti e abbondante acqua per sciacquare il liquido dei freni qualora si rovesciasse sulle superfici verniciate.
Informational PurposesAn informational icon, calling your attention
Nota
Dispose of used brake fluid in a manner consistent with local environmental codes.
Informational PurposesAn informational icon, calling your attention
Nota
This procedure is applicable to both Model 3 base and sport brake calipers.

Torque Specifications

Table 1. Torque Specifications: Brake Caliper - Rear
Description Torque Value Reuse/Replace Notes
LH rear brake caliper bracket to the knuckle
83 Nm (61.2 lbs-ft)
Replace 1088969-00-B
Brake hose to the LH rear brake caliper
42 Nm (31.0 lbs-ft)
Replace 1044731-00-D
LH rear brake caliper electrical harness clips
5 Nm (3.7 lbs-ft)
Reuse

Remove

  1. Raise and support the vehicle. See Raise Vehicle - 2 Post Lift.
  2. Place the vehicle into EPB Service Mode. See Parking Brake - Caliper - Rear - LH (Release).
  3. Remove the LH rear wheel. See Wheel Assembly (Remove and Install).
  4. Disconnect the electrical connector from the LH rear brake caliper.
  5. Remove the bolt that attaches the electrical harness bracket to the LH rear brake caliper.
  6. Position the oil drain under the LH rear brake caliper area.
  7. Remove the LH rear jounce hose. See .
  8. Remove and discard the bolts that attach the LH rear caliper bracket to the knuckle, and then remove the caliper from the vehicle.

Install

  1. If installed, remove the brake pads from the rear brake caliper.
  2. Use needle-nose pliers to ensure that the slots in the rear brake caliper piston face are at the 12 o'clock and 6 o'clock positions.
  3. Install the brake pads into the rear brake caliper.
  4. Install the LH rear brake caliper onto the LH rear knuckle, and then install new bolts to attach the caliper to the knuckle.
    83 Nm (61.2 lbs-ft)
  5. Install a new LH rear jounce hose. See .
  6. Remove the oil drain from underneath the vehicle.
  7. Connect the electrical connector to the LH rear brake caliper.
  8. Install the LH rear brake caliper electrical harness clips.
    5 Nm (3.7 lbs-ft)
  9. Lower the vehicle.
  10. Remove any wheel chocks, and then shift the vehicle into Park.
  11. Reinstall the vehicle firmware. See .
  12. Perform the bleed procedure for the LH rear brake caliper. See Brake Fluid Bleed - One Caliper.
  13. Install the LH rear wheel. See Wheel Assembly (Remove and Install).
  14. Perform a vehicle road test using a series of ABS-active stops and make sure proper brake pedal feel and performance is achieved.