29/09/2024 00:00:52

Batería de alta tensión (Tracción a las ruedas traseras) (Paquete estructural) (Trifásico) (Desinstalación e instalación)

Código de corrección 16010131 4.14 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección anterior y el FRT reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga.NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. Para enviar sus comentarios sobre los valores de FRT, escriba a LaborTimeFeedback@tesla.com. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento.

  • 2024-06-13: Updated lift pad adapter PNs.
  • 2023-11-21: Added new lift pad instructions.
  • 2023-11-07: Added references to wade seal procedures.
Special Tools required for this procedure:
  • 1936724-00-A - Adaptadores universales para soporte de elevación
  • 1020566-00-F Conjunto, mesa de batería, elevación manual
  • 1065131-00-A Battery Coolant Drain Kit
  • 1108272-00-B Tapa, conector lógico, inversor, 3DU
  • 1050448-00-B Coolant Vacuum Refill Tool
  • 1754057-00-A Current Probe, Clamp, DC, 600V
  • 1076927-00-A Hioki Tester
  • 1129166-00-A Polipasto, bastidor en H, EMEA
  • 1133787-00-A Key, Seat Belt Release, Model 3
  • 1134523-00-B Kit, Alignment Rods, Battery, M3
  • 1133843-00-A Kit, adaptadores de drenaje y llenado de refrigerante, M3
  • 1479505-00-A Kit, M3 Vacuum Fill Coolant Adapter
  • 1135762-00-A Kit, tapón de mantenimiento, manguera de refrigeración, Model 3
  • 1637160-00-A MYSP and Palladium Pack Lift Attachment
  • 1076928-00-A Test Probes - Hioki 9461
  • 1080589-00-A Wheel Chocks
Warning IconA warning icon, calling your attention to a possibly risky situation
Aviso

Solo los técnicos que hayan recibido formación en sistemas de alta tensión y hayan completado todos los cursos de certificación necesarios (si procede) pueden realizar este procedimiento. Siempre que se manipule un cable, barra colectora o conexión de alta tensión, deben llevarse equipos de protección individual (EPI) y guantes aislantes para alta tensión con una clasificación nominal mínima de 0 (1000 V). En la nota técnica TN-15-92-003 sobre los puntos de peligro de alta tensión, encontrará más información sobre seguridad.

Retirar

  1. Remove the LH rocker panel carrier. See Soporte - Panel de estribo - Lado izquierdo (Desinstalación y sustitución).
  2. Remove the butyl patches (x2) that cover the LH rocker access holes.
  3. Instale los adaptadores de los apoyos de elevación.
    • Solo en EMEA, instale Adaptador, apoyo de elevación, Model Y (1614078-00-A)
    • En otras regiones, instale los adaptadores universales para soporte de elevación (1936724-00-A).
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Aviso
    NO utilice ningún otro adaptador para soporte de elevación.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Fuera de EMEA, los adaptadores universales para soporte de elevación (1936724-00-A) sustituyen a Adaptador, apoyo de elevación, Model Y (1614078-00-A). Deseche otras versiones de los adaptadores de los apoyos de elevación.
    Informational PurposesAn informational icon, calling your attention
    Nota
    En EMEA, los adaptadores de los apoyos de elevación no están todavía disponibles. Asegúrese de instalar los apoyos de elevación adecuados para cada modelo: los de goma en el Model Y, y los indicados para el Model 3 en el Model 3.

    Instrucciones para los adaptadores de los apoyos de elevación:

    1. Dependiendo del tipo de elevación, instale el adaptador de rosca correcto en el adaptador de elevación.
    2. Asegúrese de instalar y apretar la arandela de retención de la rosca en la parte inferior del adaptador de elevación. Si la arandela de retención de la rosca no está instalada, no continúe usando el adaptador de elevación.
    3. Instale los adaptadores de elevación en los brazos del elevador de forma que el apoyo de color negro quede orientado hacia el vehículo.
      Warning IconA warning icon, calling your attention to a possibly risky situation
      Aviso
      Compruebe que la orientación de instalación del adaptador sea la adecuada.
    4. Alinee los brazos del elevador con el orificio de referencia del vehículo.
    5. Eleve los brazos para asentar completamente los apoyos de elevación en el vehículo.
    6. Asegúrese de que los 4 quedan completamente asentados en el vehículo.
  4. Open all doors and lower the windows.
  5. Release the LH and RH parking brake calipers. See Freno de estacionamiento - Pinza - Trasero - Lado izquierdo (Desbloqueo).
  6. Run the Thermal Fill Drain (Coolant Only) routine using the touchscreen. See Sistema de refrigeración (Paquete estructural) (Drenaje y llenado).
    Informational PurposesAn informational icon, calling your attention
    Nota
    Select Thermal > Coolant System > Coolant Fill/Drain, then touch Run. Close once the routine is completed.
  7. Remove the seats and the interior carpet from the vehicle. See Moqueta - Interior completa (Desinstalación y sustitución).
  8. Remove the center console. See Consola central (2.0) (Paquete estructural) (Desinstalación e instalación).
  9. Release the center console harness from the HV battery.
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x clip
  10. Remove the bolts (x4) that attach the LH and RH lower IP carrier brackets.
  11. Secure the center seat belt buckles away from the ancillary bay.
  12. Remove the rear inner HV battery bolts (x4).
  13. Push the vehicle onto a 2-post lift.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Assistance recommended. Note that this vehicle can only be safely pushed for a very short distance and at very slow speed.
  14. Raise and support the vehicle. See Elevación del vehículo - Elevador de 2 columnas.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Verify jack locations prior to lifting vehicle, ONLY place on lifting points at front and rear of rocker panels
  15. Raise vehicle fully and lower the lift onto locks.
  16. Remove the front aero shield panel. See Panel - Deflector aerodinámico - Delantero (Paquete estructural) (Desinstalación y sustitución).
  17. Pull the RH front wheel liner away from the HV battery.
  18. Pull the LH front wheel liner away from the HV battery.
  19. Remove the mid aero shield panel. See Panel - Deflector aerodinámico - Central (Desinstalación y sustitución).
  20. Realice el procedimiento de desactivación de la alta tensión del vehículo. Consulte Procedimiento de desactivación de la alta tensión del vehículo (Paquete estructural).
  21. Lower the vehicle until the tires are touching the ground.
  22. Release the 2nd row 60 seat connector from the LH seat frame.
  23. Disconnect the 3-phase connector from the HV battery.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Release locking tab upwards then lift up the connector.
  24. Remove the bolt that attaches the busbar cover access door.
  25. Remove the bolts that attach the charge port busbar kit to the HV header.
  26. Release the LH body harness from the rear body and move it aside.
  27. Lift the busbar kit connector to remove it from the HV header.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Use an inflatable airbag to suspend the busbar away from the HV header during removal and installation. Hold busbar firmly as there is tension on it.
    F
    F
  28. Disconnect the HVC logic connector and install the logic cap.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Release the locking tab, then pivot the handle downward to release connector.
  29. Disconnect the LV power connector from the HV battery.
  30. Close all doors.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Latch the rear doors to prevent accidental closure.
  31. Raise the vehicle to a comfortable working height.
  32. Position a coolant drain container underneath the LH front of the HV battery.
  33. Disconnect the PT supply hose at the LH front side of the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Plug the hose connections.
  34. Position the coolant drain container underneath the LH RDU area.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Position neck to catch all coolant loss.
  35. Release the RDU inverter inlet hose from the RDU.
  36. Disconnect the RDU inverter inlet hose from the fluid coupling.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Plug the drive unit coupling.
  37. Position the coolant drain container underneath the front left manifold battery supply hose.
  38. Disconnect the front left manifold battery supply hose.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Plug hose connections.
  39. Position the coolant drain container underneath the RH front of the HV battery.
  40. Disconnect the HV battery RH front inlet hose.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Plug hose connections.
  41. Release the clip that attaches the HV battery RH front inlet hose to the skid plate.
  42. Position the coolant drain container underneath the RH front of the HV battery.
  43. Disconnect the PT return hose at the RH front side of the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Plug hose connections.
  44. Release the clip that attaches the PT return hose to the RH front side of the HV battery pack.
  45. Release the PT coolant hose from the LH side of the front HV battery bash plate.
  46. Position the coolant drain container underneath the LH rear side of the HV battery.
  47. Remove the RDU inverter inlet hose.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Rotate the hose between the subframe and battery out of the vehicle.
  48. Disconnect the compressor HV harness from the HV battery.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Hold down the red locking tab, and the disengage the release lever. Do not force the release lever up.
  49. Release the clips (x4) that attach the compressor HV harness to the HV battery.
  50. Release the RDU oil cooler outlet pipe.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Plug hose connections.
  51. Remove the RDU oil cooler outlet pipe.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Rotate the pipe down over the RDU and rearward around the subframe.
  52. Remove the coolant drain container from underneath the vehicle.
  53. Release the RDU HV cable bracket from the RDU.
  54. Disconnect the RDU HV cable from the RDU.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Release the locking tab, and then rotate the release lever up to disengage the connector. Do not force the release lever up.
  55. Remove the RDU HV cable.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Rotate the cable underneath the logic cable harness between the subframe and the HV battery.
  56. Remove the smaller bolts of the LH and RH shear plates.
  57. Loosen the large bolt that attaches the LH shear plate and subframe to the body and rotate the shear plate clear of the HV battery.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Hand tighten the bolt once the shear plate is in position.
  58. Loosen the large bolt that attaches the RH shear plate and subframe to the body and rotate the shear plate clear of the HV battery.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Hand tighten the bolt once the shear plate is in position.
  59. Put the battery table into position and lower vehicle to support the battery.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Assistance is recommended. Line up the table so the bolts at the front bash plate are accessible and the rear HV cables are accessible. Adjust the final battery table position using adjustable caster jacks on the table.
  60. Loosen the front bolts that attach the HV battery through the skid plate cover with ratchet, and then remove them with a battery powered drill.
  61. Loosen the bolts that attach the skid plate to the vehicle with a ratchet, and then remove them with a battery powered drill.
  62. Loosen the bolts that attach the rear HV battery to the vehicle with a ratchet, and then remove them with a battery powered drill.
  63. Loosen the LH bolts that attach the HV battery to the vehicle with a ratchet, and then remove them with a battery powered drill.
  64. Loosen the RH bolts that attach the HV battery to the vehicle with a ratchet, and then remove them with a battery powered drill.
  65. Raise the vehicle to free it from the HV battery.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Assistance is recommended.
  66. Remove the battery from under the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Assistance is recommended.

Instalar

Informational PurposesAn informational icon, calling your attention
Nota
Si alguna de las roscas de la pieza fundida de los bajos delanteros (FUB) o de los bajos traseros (RUB) está dañada, consulte TN-15-92-001 - Instalación de insertos Helicoil para ver las instrucciones de reparación con insertos Helicoil.
Warning IconA warning icon, calling your attention to a possibly risky situation
PRECAUCIÓN
Para realizar reparaciones en las roscas de FUB o RUB, use únicamente insertos Helicoil con TPN 1056157-09-A.
Informational PurposesAn informational icon, calling your attention
Nota
Si se ha realizado una reparación de rosca, añada el código de corrección 70060005 - Reparación de rosca como actividad independiente a la visita de servicio.
  1. Inspect and clean the wade seal on the HV battery prior to installation.
    If the wade seal is damaged, rework or replace the seal.
  2. Clean the HV connector contact surface of any residual Penetrox.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Allow 1 minute dry time after removing Penetrox. New busbar comes with Penetrox applied to the HV connector.
  3. Clean the busbar HV connector contact surface of any residual Penetrox.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Allow 1 minute dry time after removing Penetrox. It is necessary to clean the HV connector during re-use of the busbar.
  4. Apply Penetrox onto the HV connector joints.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Apply 2 drops of Penetrox A-13 about 5mm in diameter to either side of the hole on both leads. Spread evenly to ensure that the contact surface is fully covered.
  5. Install the HV battery alignment rods (x2) onto the body.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Only use the smaller rods. Thread onto RH front most and LH rear most side holes.
  6. Position the HV battery pack under the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Assistance is recommended.
  7. Carefully lower the vehicle onto the HV battery pack and align the battery holes with the rods.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Assistance is recommended. Make sure that coolant hoses and harnesses do not get pinched.
  8. Remove the HV battery alignment rods from the body once the HV battery is aligned.
  9. Thread in by hand all bolts that attach the HV battery to the vehicle. Do not install bolts to the shear plates yet.
    Informational PurposesAn informational icon, calling your attention
    Nota
    34x bolts. Includes top bolts. Start with bolts nr. 35-36-37-38 Ensure smooth thread engagement and bolts are not cross threaded into the casting.
  10. Completely lower the vehicle onto the battery pack.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Assistance is recommended.
  11. Seat all bolts (x34) that attach the HV battery to the vehicle with a battery powered drill.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Ensure smooth thread engagement and bolts are not cross threaded into the casting. Flush down the bolts. Do not over tighten bolts, fully torque them at later steps.
  12. Fully torque the LH bolts (x7) that attach the HV battery to the vehicle (torque 56 Nm).
    Informational PurposesAn informational icon, calling your attention
    Nota
    Bolt position 1-7.
  13. Fully torque the RH bolts (x7) that attach the HV battery to the vehicle (torque 56 Nm).
    Informational PurposesAn informational icon, calling your attention
    Nota
    Bolt position 16-22.
  14. Fully torque the rear bolts (x4) that attach the HV battery to the vehicle (torque 62 Nm).
    Informational PurposesAn informational icon, calling your attention
    Nota
    Bolt position 10-13.
  15. Fully torque the front bolts (x6) that attach the HV battery through the bash plate openings (torque 90 Nm).
    Informational PurposesAn informational icon, calling your attention
    Nota
    Later production vehicles have E14 bolts torqued at 75 Nm. Bolt location 23 to 28.
  16. Fully torque the front bolts (x6) that attach the bash plate to the vehicle (torque 62 Nm).
    Informational PurposesAn informational icon, calling your attention
    Nota
    Bolt location 29-34.
  17. Loosen the RH rear subframe bolt and align the RH rear shear plate with the HV battery.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Hand tighten bolt once the shear plate is in position.
  18. Install the bolts that attach the RH shear plate to the HV battery hand tight.
  19. Torque the large bolt that attaches the subframe and RH rear shear plate to the body (torque 130 Nm).
  20. Torque the 2 smaller bolts that attach the RH rear shear plate to the body (torque 62 Nm).
  21. Repeat steps 42 through 45 on the LH side of the vehicle.
  22. Open the LH rear door.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Use caution while working around this area not to damage any components.
  23. Fully torque the LH rear inner bolts (x2) that attach the HV battery pack to the vehicle (torque 49 Nm).
    Informational PurposesAn informational icon, calling your attention
    Nota
    Bolt position 35-36.
  24. Visually inspect the wade seal to make sure that no gaps are present.
  25. Close LH rear door.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Do not latch the door.
  26. Open the RH rear door.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Use caution while working around this area not to damage any components
  27. Fully torque the RH rear inner bolts that attach the HV battery pack to vehicle (torque 49 Nm).
    Informational PurposesAn informational icon, calling your attention
    Nota
    Bolt position 37-38.
  28. Close RH rear door
    Informational PurposesAn informational icon, calling your attention
    Nota
    Do not latch the door.
  29. Raise vehicle and lower onto locks, then remove the battery table from under the vehicle.
  30. Position the RDU HV cable up to the RDU.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Rotate cable underneath logic cable harness between subframe and HV battery.
  31. Connect the RDU HV cable onto the RDU.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Verify lever is in the upright and open position, then carefully seat connector and allow the lever to engage. Fully secure lever and verify red tab is locked. Do not damage any pins.
  32. Secure the RDU HV harness onto the HV battery.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Verify lever is in the upright and open position, then carefully seat the connector and allow the lever to engage. Fully secure the lever and verify that the red tab is locked. Do not damage any pins.
  33. Install the bolt that attaches the RDU HV cable bracket to the RDU (torque 6 Nm).
  34. Install the RDU oil cooler outlet pipe.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Rotate up over the RDU and rearward around the subframe to oil cooler.
  35. Attach the RDU oil cooler outlet pipe.
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x spring clips, 5x clips. Remove plugs as needed
  36. Attach the compressor HV harness to the HV battery.
    Informational PurposesAn informational icon, calling your attention
    Nota
    4x clips
  37. Connect the compressor HV harness onto the HV battery.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Verify that the lever is in the upright and open position, then carefully seat the connector and allow the lever to engage. Fully secure lever and verify that the red tab is locked.
  38. Install the RDU inverter inlet hose.
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x spring clip, 1x clip. Rotate between subframe and battery into the RDU and PCS outlet. Remove plugs as needed.
  39. Attach the RDU inverter inlet hose to the RDU HV cable.
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x clip
  40. Install the mid aero shield panel. See Panel - Deflector aerodinámico - Central (Desinstalación y sustitución).
  41. Position a coolant drain container underneath the LH front of the HV battery.
  42. Connect the PT supply hose at the LH front side of the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x spring clip. Remove plugs as needed.
  43. Attach the PT coolant hose onto the LH side of the front HV battery bash plate.
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x clip
  44. Position the coolant drain container underneath the RH front of the HV battery.
  45. Connect the PT return hose at the RH front side of vehicle.
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x spring clip. Remove plugs as needed.
  46. Attach the PT return hose to the RH front side of the HV battery pack.
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x clip
  47. Connect the HV battery RH front inlet hose.
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x spring clip. Remove plugs as needed.
  48. Attach the HV battery RH front inlet hose to the skid plate.
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x clip
  49. Position the coolant drain container underneath the front left manifold battery supply tube.
  50. Connect the front left manifold battery supply tube.
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x spring clip, 1x clip. Remove plugs as needed.
  51. Remove the coolant drain container from underneath the vehicle.
  52. Release the LH front wheel liner from the bungee strap.
  53. Release the RH front wheel liner from the bungee strap.
  54. Install the front aero shield panel. See Panel - Deflector aerodinámico - Delantero (Sin paquete estructural) (Desinstalación y sustitución).
  55. Fully lower the vehicle, and then push the vehicle away from the lift.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Assistance is recommended. Place wheel chocks to prevent the vehicle from moving. Note that this vehicle can only be safely pushed for a very short distance and at very slow speed.
  56. Open all doors
    Informational PurposesAn informational icon, calling your attention
    Nota
    Latch rear doors to prevent accidental closure
  57. Connect the LV power connector to the HV battery.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Push the red locking tab down to secure the connection.
  58. Remove the HVC logic cap, and then connect HVC logic connector.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Pivot the handle upward to engage the connector and secure the locking tab.
  59. Position the busbar kit connector and lower it onto the HV header.
  60. Install the bolts (x2) that attach the charge port busbar kit to the HV Header (torque 9 Nm).
  61. Put on HV insulating gloves and leather over gloves.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Check gloves for damage and expiry details. Refer to Service Document TN-15-92-003 for further details.
  62. Perform a Hioki resistance test at each HV joint from HV busbar lead to bolt head.
    Informational PurposesAn informational icon, calling your attention
    Nota
    The acceptable resistance is between 0.050 mΩ (50 μΩ) and 0.195 mΩ (195 μΩ). If the resistance is greater than 0.195 mΩ (195 μΩ), there is too much resistance in the High Voltage joint. Remove the fastener, clean areas with isopropyl alcohol, install fastener back and test again. If the resistance is lower than 0.050 mΩ (50 μΩ), reposition the probes and measure again. If the resistance is repeatedly between 0.00 mΩ and 0.050 mΩ (50 μΩ), the Hioki test passed; proceed to the next step.
  63. Remove leather over gloves and HV insulating gloves.
  64. Install the bolt that attaches the busbar cover access door (torque 9 Nm).
  65. Install the LH body harness onto the rear body.
  66. Connect the 3-phase connector onto the HV battery.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Pivot the handle downwards to engage the connector and secure the locking tab.
  67. Attach the 2nd row 60 seat connector to the LH seat frame.
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x clip.
  68. Remove the tape from the seat frame.
  69. Install the bolts (x4) that attach the LH and RH lower IP carrier brackets (torque 25 Nm)..
  70. Install the center console harness to the HV battery.
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x clip.
  71. Install the center console. See Consola central (2.0) (Paquete estructural) (Desinstalación e instalación).
  72. Install the seats and the interior carpet to the vehicle. See Moqueta - Interior completa (Desinstalación y sustitución).
  73. Perform a vacuum refill of the cooling system. See Sistema de refrigeración (Llenado por vacío).
  74. Connect LV power. See Alimentación de 12 V/baja tensión (Desconexión y conexión).
  75. Press and hold the Park button to exit EPB service mode.
  76. Access the thermal system routines using the UI: Select Quick Controls (vehicle icon) > Service Mode > Thermal > Actions.
  77. Unlock the vehicle gateway. See Puerta de enlace (Desbloquear).
  78. Perform a coolant purge from the touchscreen.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Touch time only. Wait until coolant pumps stop running (audible noise), "Routine Passed" appears, but pumps will run for 10 minutes. If you start another routine during this time, it will fail. Make sure vehicle is not in "Drive". Routine is still running despite the completed message. Speeds can be monitored in garage under PT Thermal tab, Idle speed = ~1500 RPM. The rest will vary speeds from 3500-6500 RPM and actuate valves between SERIES and PARALLEL. Putting the vehicle into "Drive" will stop this routine. If speeds hover at 7000 RPM, this indicates the pumps are air locked; perform a vacuum fill. Continue to add coolant and purge until the coolant level reaches between the NOM and MAX Lines on the bottle.
  79. Inspect the coolant level at the reservoir and top off as necessary.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Ensure coolant is filled using G-48 coolant.
  80. Install the coolant bottle cap.
  81. Perform the Thermal Performance Test using the touchscreen: touch Thermal > Actions > Test Thermal Performance > Start, touch Run and allow the routine to complete.
  82. Exit Service Mode through the touchscreen.
  83. Install the HEPA filter assembly. See Conjunto - Filtro - HEPA (Desinstalación y sustitución).
  84. Install the rear underhood apron. See Faldón del vano del motor - Parte trasera (Desinstalación y sustitución).
  85. Remove the lift pad adapters from LH and RH rocker panel.
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x lift pad adapters per side.
  86. Install butyl patches onto the LH and RH rocker panel access holes.
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x butyl patches per side. Apply pressure along patch to verify it is fully secured to body. Use new butyl patches if needed, Roughly 2" x 2 1/2"
  87. Install the LH and RH rocker panel carrier. See Soporte - Panel de estribo - Lado izquierdo (Paquete estructural) (Desinstalación y sustitución).
  88. Install the LH and RH rocker panel covers onto the rocker panel carrier. See Cubierta - Panel de estribo - Inferior - Lado izquierdo (Desinstalación y sustitución).