Release Notes July-September 2024

Archived Release Notes:

Week Ending September 28, 2024

The following procedure(s) were updated:
  1. Seat Assembly - 1st Row - LH (Remove and Replace) - Updated step for OCS self calibration routine.
  2. Seat Assembly - 1st Row - LH (Structural Pack) (Retrofit) - Removed unneeded step for OCS self calibration Toolbox routine.

Week Ending September 21, 2024

The following procedure(s) were updated:
  1. How to Use this Manual - Added information on the crowsfoot/offset wrench extension calculator.
  2. Seal - Body - Side - Rear - Primary - LH (Remove and Replace) - Update rear door primary seal install with new datum.

Week Ending September 14, 2024

The following new procedure(s) were added:
  1. Harness - Ancillary Bay - HV Battery (Non-Structural Pack) (Remove and Replace)
The following procedure(s) were updated:
  1. A/C Line - Supermanifold to HVAC (Remove and Replace) - Added note on adding correction code for refrigerant - recovery/recharge as a separate activity to the Service Visit.
  2. Antenna - GPS/GNSS (Remove and Replace) - Added note that it is not necessary to disconnect harness from camera assembly.
  3. Car Computer (Remove and Replace) - Added owner authorization request and LV maintainer steps.
  4. All HV Battery (Remove and Replace) procedures - Added step to support the LV system.
  5. Desiccant (Remove and Replace) - Added warnings to wear suitable protective clothing, consisting of face and eye protection, heat-proof gloves, rubber boots and apron or waterproof overalls must be worn when carrying out operations on the air conditioning system.
  6. TPMS (Sensor ID Tool Learn) - Added note with links to update TPMS Tool firmware.

Week Ending September 7, 2024

The following procedure(s) were updated:
  1. HV Battery (RWD) (Remove and Replace) - Added "High Voltage Awareness" certification warning.

Week Ending August 31, 2024

The following procedure(s) were updated:
  1. Alignment Requirement - Suspension - Added instruction on proper consumption of alignment adjustment correction codes.
  2. Clear Forward Camera View (Precision Cleaning Of Inboard Windshield) - Added a step to clean the wiper blades.
  3. Desiccant (Remove and Replace) - Added note on adding correction code for refrigerant recovery/recharge 18200102 as a separate activity to the service visit and, re-added steps for moving the shock tower brace, if necessary and added special tools for accumulator cap removal.
  4. Tesla Badge - Rear (Remove and Replace) - Added a note to remind that the rear badge is not reusable due to the positioning problem.

Week Ending August 24, 2024

The following new procedure(s) were added:
  1. AC Cable - Charge Port to HV Battery (3-Phase) (Retrofit)
  2. Wheel Disposal (Rework)
The following procedure(s) were updated:
  1. Oil Pump - Rear Drive Unit (3DU) (Remove and Replace) - Added instruction to perform software reinstall before running oil pump-related Toolbox routines.
  2. Wheel (Remove and Replace) - Added instruction on wheel disposal.

Week Ending August 17, 2024

The following new procedure(s) were added:
  1. Car Computer (Remove and Replace) - Car Computer replacement procedure that uses Toolbox to associate the replacement computer. Please send us feedback on this procedure!
  2. LV Battery - Recover - Please send us feedback on this procedure!
  3. OBD Connector (Retrofit)
The following procedure(s) were updated:
  1. Added a note for NA vehicles to remind that the seat covers without ISOFIX flag for child locks must be replaced for the following procedures:

Week Ending August 10, 2024

The following new procedure(s) were added:
  1. Door and Hinge Cover - Charge Port (Remove and Replace)
The following procedure(s) were updated:
  1. Coolant Pump - HV Battery (RWD) (Remove and Replace) - Changed instruction for lubrication of O-rings to use Silicone lubricant instead of using silaramic grease.
  2. Coolant Pump - Powertrain (Remove and Replace) - Changed instruction for lubrication of O-rings to use Silicone lubricant instead of using silaramic grease.
  3. NVH Tape - Brake Pads - Rear (EMEA) (Retrofit) - Updated instructions to apply tape only on inner brake pads.
  4. Vehicle Sanitation - Evaporator - Tunap 994 (EMEA) - Removed procedures using Tunap 996 and Tunap I5880 from original procedure.
  5. Vehicle Sanitation - Interior Air - Tunap 589 (EMEA) - Modified procedure for use of Tunap 589 only.

Week Ending August 3, 2024

The following procedure(s) were updated:
  1. Contactor - Fast Charge - HV Battery (Remove and Replace) - Updated references in Install section.
  2. Cover - Ancillary Bay (7-Seat) (Remove and Replace) - Added information on installing a recycling warning label with CE marking and manufacturer information, if this was present on the ancillary bay cover being replaced.
  3. Cover - Ancillary Bay (Remove and Replace) - Added information on installing a recycling warning label with CE marking and manufacturer information, if this was present on the ancillary bay cover being replaced.
  4. IP Carrier (Remove and Replace) - Added information about how to handle the replacement between different versions of IP carrier.
  5. Mirror - Rear View (Remove and Replace) - Added steps for AP4 vehicles.
  6. Windshield (HW4) (Remove and Replace) - Added video.

Week Ending July 27, 2024

The following new procedure(s) were added:
  1. Seat Assembly - 1st Row - LH (Structural Pack) (Retrofit)
The following procedure(s) were updated:
  1. Cover - Ancillary Bay (Structural Pack) (3-Phase) (Remove and Replace) - Added information on installing a recycling warning label with CE marking and manufacturer information, if this was present on the ancillary bay cover being replaced.
  2. Cover - Seat Back - 2nd Row - LH (5-Seat) (Remove and Replace) - Added a note for NA vehicles to remind that the seat covers without ISOFIX flag for child locks must be replaced.
  3. Cover - Seat Back - 2nd Row Seat - RH (Remove and Replace) - Added a note for NA vehicles to remind that the seat covers without ISOFIX flag for child locks must be replaced.
  4. Fuse Locations - Update the link of Electrical Information.
  5. Seat Back - 2nd Row - LH (Remove and Replace) - Deleted the seatback cushion separation steps.
  6. Seat Back - 2nd Row - RH (Remove and Replace) - Added a note for NA vehicles to remind that the seat covers without ISOFIX flag for child locks must be replaced.
  7. Toolbox 3 (Connect and Disconnect) - Added instructions and warning for OBD-II to RJ45 Ethernet diagnostic equipment.

Week Ending July 20, 2024

The following procedure(s) were updated:
  1. Controller - High Voltage (Backup and Restore) - Introduced Service Mode Plus activation using the Vehicle Ops App, updated touchscreen images for backing up and restoring backup data.
  2. Jumper Harness - Trailer Hitch (Remove and Replace) - Added extra image to installation procedure.
  3. Light - Fog / Reverse - Rear - LH (Remove and Install) -
  4. Module - Body Controller - Security (Remove and Replace) - Updated the way of performing the routines from using Toolbox to using the touchscreen.
  5. NVH Tape - Brake Pads - Front (EMEA) (Retrofit) - Updated procedure for pre-cut stickers and added region information.
  6. NVH Tape - Brake Pads - Rear (EMEA) (Retrofit) - Updated procedure for pre-cut stickers and added region information.

Week Ending July 13, 2024

The following procedure(s) were updated:
  1. A/C Compressor, Supermanifold and A/C Lines (Remove & Replace) - Added details to identify the type of A/C line to be used in "refrigACLineType" configuration.

Week Ending July 6, 2024

The following procedure(s) were updated:
  1. Ancillary Bay Coolant (Drain and Refill) - Added caution for hose reconnection.
  2. Brake Fluid Bleed - One Caliper - Corrected torque figures for brake caliper bleed valves.
  3. Clear Forward Camera View (Precision Cleaning Of Inboard Windshield) - Updated tool part numbers.
  4. Mount - Front Drive Unit - LH (Remove and Replace) - Changed last step to perform alignment check/adjust to reference to alignment requirement table.