18/03/2024 08:28:40
Module - Body Controller - Front (RWD) (Remove and Replace)
Correction code 17152902 0.90 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.
- 2024-03-18: Added instructions to check the integrity of the controller module cover seal and to replace the cover if any damage is found.
Remove
- Remove the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).
- Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
- Remove the cabin intake duct. See GUID-7807CF2B-360B-49FB-A983-B26A7519F6A7.html#GUID-7807CF2B-360B-49FB-A983-B26A7519F6A7.
- Remove the hood latch cover. See GUID-33033115-BAEE-4611-A010-E6609D17B007.html#GUID-33033115-BAEE-4611-A010-E6609D17B007.
- Remove the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
- Remove the LH and RH wiper arms. See Wiper Arms (Remove and Replace).
- Remove the cowl screen panel. See Panel - Cowl Screen (Remove and Replace).
- Disconnect 12V power. See 12V/LV Power (Disconnect and Connect).
- Remove the 12V battery strap. See Strap - 12V Battery (Remove and Replace).
- Remove the 12V auxiliary battery. See 12V/LV Battery (Remove and Replace).
- Remove the 12V battery bracket. See GUID-DD31DE14-FFCC-4E62-84E1-02CE1E0DAEE7.html.
- Remove the bolt that attaches the thermal harness cover to the front body controller module, and then remove the cover from the module.
- Disconnect the thermal harness from the front body controller module connector.
- Release the clip that attaches the suction / liquid A/C combination lines to the body near the TXV, and then move the electrical harness aside to gain access to the front body controller module.
-
Remove the bolts (x9) that attach the front body controller module cover to the front body controller module, and then remove the cover.
NoteCheck the condition of the cover seal; if any damage is found, order a new front body controller module cover.
- Disconnect the electrical harness from the front body controller module connectors (x4).
- Remove and discard the nuts (x6) and bolt that attach the power and ground cables to the front body controller module.
- Remove the bolts (x3) that attach the front body controller module to the body.
- Release the clips (x2) that attach the bottom of the front body controller module to the body, and then remove the lower busbar from the stud.
- Remove the bolt that attaches the ground strap to the upper rear of the front body controller module, and then remove the ground strap from the module.
- Remove the bolt that attaches the ground strap to the lower right side of the front body controller module, and then remove the ground strap from the module.
- Remove the bolt that attaches the ground strap to the lower rear of the front body controller module, and then remove the ground strap from the module.
- Remove the front body controller module from the vehicle.
Install
Note
Modules that are revision -K and later do not have the ground busbar and stud in the top corner. These modules are not faulty and the ground busbar and stud to not need to be installed onto the new part.
- Set the front body controller module where it installs into the vehicle, and then tilt the module forward
-
Install the ground strap to the lower rear of the front body controller module, and then install the bolt that attaches the ground strap to the module.
-
Install the ground strap to the lower right side of the front body controller module, and then install the bolt that attaches the ground strap to the module.
-
Install the ground strap to the upper rear of the front body controller module, and then install the bolt that attaches the ground strap to the module.
- Slide the busbar onto the lower stud, and then fasten the electrical harness clips (x2) to the bottom of the front body controller module.
-
Install the bolts (x3) that attach the front body controller module to the body.
-
Install new nuts (x6) and new bolt to attach the power and ground cables to the front body controller module.NoteMake sure that the terminal lugs fit in their channels neatly.
- Connect the electrical harness to the front body controller module connectors (x4).
-
Visually inspect that the power and the ground cables exit the front body controller module neatly in their respective channels, and parallel to each other.
CAUTIONMake sure that no cables or wires will be pinched when the front body controller module cover is installed.
-
Install the front body controller module cover to the front body controller module, and then install the bolts (x9) that attach the cover to the module.CAUTIONMake sure that the cover seal has no damage. If any damage is found, a new front body controller module cover must be installed. Failure to do so may result in water ingress into the front body controller module.
- Connect the thermal harness to the front body controller module connector.
- Fasten the clip that attaches the suction/liquid lines to the body near the TXV.
-
Install the thermal harness cover to the front body controller module, and then install the bolt that attaches the cover to the module.
- Install the 12V battery bracket. See GUID-DD31DE14-FFCC-4E62-84E1-02CE1E0DAEE7.html.
- Install the 12V auxiliary battery. See 12V/LV Battery (Remove and Replace).
- Install the 12V battery strap. See Strap - 12V Battery (Remove and Replace).
- Connect 12V power. See 12V/LV Power (Disconnect and Connect).
- Reinstall the vehicle firmware. See Software Reinstall - Touchscreen.
- In Toolbox, click Actions, type "VCFRONT" in the search field, click the Play button next to "TESTRESET_ VCFRONT", and then select Run.
- Disconnect the laptop from the vehicle.
- Install the cowl screen panel. See Panel - Cowl Screen (Remove and Replace).
- Install the LH and RH wiper arms. See Wiper Arms (Remove and Replace).
- Install the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
- Install the hood latch cover. See GUID-33033115-BAEE-4611-A010-E6609D17B007.html#GUID-33033115-BAEE-4611-A010-E6609D17B007.
- Install the cabin intake duct. See GUID-7807CF2B-360B-49FB-A983-B26A7519F6A7.html#GUID-7807CF2B-360B-49FB-A983-B26A7519F6A7.
- Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
- Install the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).
- Perform the headlights adjust procedure. See: