Release Notes April-June 2024

Archived Release Notes:

Week Ending June 29, 2024

The following procedure(s) were updated:
  1. Headlamps (SAE-to-Global) - Headlamp Assembly - Pair (Retrofit) - Updated Toolbox 3 headlamps configuration "Global" direction.
  2. NVH Tape - Brake Pads - Front (EMEA) (Retrofit) - Updated notes.
  3. NVH Tape - Brake Pads - Rear (EMEA) (Retrofit) - Updated notes.

Week Ending June 22, 2024

The following procedure(s) were updated:
  1. A/C Compressor, Supermanifold and A/C Lines (Remove & Replace) - Added the step of updating coolant pump configuration.
  2. Check Valve - Liquid Cooled Condenser (Remove and Replace) - Added step to make sure that the A/C system is depressurized before removing the cooled condenser check valve and added running ODIN routines through the touchscreen.
  3. Flood Ports - 2nd Generation (Remove and Replace) - Deleted ancillary bay air leak test.

Week Ending June 15, 2024

The following procedure(s) were updated:
  1. Brake Fluid Bleed/Flush - Corrected torque figures for brake caliper bleed valves.
  2. Cap - Wheel (Remove and Replace) - Added guidance on installing light/dark wheel covers onto matching wheels.
  3. Clear Forward Camera View (Precision Cleaning Of Inboard Windshield) - Updated the inspection method and diagrams and added the tool list.
  4. Desiccant (Remove and Replace) - Added caution for Schrader valves.
  5. Headlights - Adjust - Global (Tool Method) - Updated procedure to latest validation.
  6. HV Battery (AWD) (7-Seat) \(Remove and Install\) - Updated lift pad adapter PNs.
  7. HV Battery (AWD) (Non-Structural Pack) (Remove and Replace) - Updated lift pad adapter PNs. Added pyro disconnect removal steps.
  8. HV Battery (AWD) (Structural Pack) (Remove and Install) - Updated lift pad adapter PNs.
  9. HV Battery (AWD) (Structural Pack) (Remove and Replace) - Updated lift pad adapter PNs. Added pyro disconnect removal steps.
  10. HV Battery (RWD) (Remove and Replace) - Updated lift pad adapter PNs. Added pyro disconnect removal steps.
  11. HV Battery (RWD) (Structural Pack) (3-Phase) (Remove and Install) - Updated lift pad adapter PNs.
  12. HV Battery (RWD) (Structural Pack) (3-Phase) (Remove and Replace) - Updated lift pad adapter PNs.

Week Ending June 8, 2024

The following procedure(s) were updated:
  1. Assembly - Filter - HEPA (Remove and Replace) - Added cabin filter health score reset for SW versions 2024.14+
  2. Brake Caliper - Front - LH (Remove and Replace) - Updated the torque specification table.
  3. Bump Stop - Liftgate - LH (Remove and Replace) - Added link to Toolbox article for additional information on bump stop adjustment.
  4. Filter - Cabin (Remove and Replace) - Added cabin filter health score reset for SW versions 2024.14+
  5. Filters – Carbon and HEPA (Remove and Replace) - Added cabin filter health score reset for SW versions 2024.14+
  6. Firmware Update - Mobile Connector - Added steps to update Mobile Connector firmware on vehicles operating software version 2024.14+.
  7. Sensor - Wheel Speed - ABS - Front - LH (Remove and Replace) - Updated the wheel speed sensor bolt from a one-off bolt to a reusable one, and added the torque specification table.
  8. Stabilizer Bar - Front (Remove and Replace) - Added a torque specification table with replaced bolt part numbers.
  9. Vehicle HV Disablement Procedure - Added warning to measure the specified order of locations for high voltage.
  10. Vehicle HV Disablement Procedure (7-Seater) - Added warning to measure the specified order of locations for high voltage.
  11. Vehicle HV Disablement Procedure (Structural Pack) - Added warning to measure the specified order of locations for high voltage.
  12. Window Regulator (Recalibrate) - Updated calibration steps using the touchscreen.

Week Ending June 1, 2024

The following procedure(s) were updated:
  1. A/C Compressor, Supermanifold and A/C Lines (Remove & Replace) - Updated the procedure per the latest validation.
  2. Bracket - Brake Caliper - Rear - LH (Remove and Replace) - Updated references and cautions.
  3. Brake Caliper - Rear - LH (Remove and Replace) - Updated EPB Service Mode reference.
  4. Brake Pad Kit - Rear (Base Brakes) (Remove and Replace) - Updated references and cautions.
  5. Brake Pad Kit - Rear (Sport Brakes) (Remove and Replace) - Updated references and cautions.
  6. Brake Rotor - Rear - LH (Remove and Replace) -
  7. Clean and Lubricate Brake Calipers (Non-Performance Brakes) - Updated references and cautions.
  8. Clean and Lubricate Brake Calipers (Performance Brakes) - Updated references and cautions.
  9. Link - Aft - Upper - Rear - LH (Remove and Replace) - Added instructions for LH rear ride height sensor.
  10. Motor - Brake Caliper - Rear - LH (Remove and Replace) - Updated EPB Service Mode reference.
  11. Parking Brake - Caliper - Rear - LH (Release) - Added method using Service Mode.
  12. Shield - Dust - Brake - Rear - LH (Remove and Replace) - Updated EPB Service Mode reference.

Week Ending May 25, 2024

The following new procedure(s) were added:
  1. Shunt - HV Battery (Non-Structural Pack) (Remove and Replace)
The following procedure(s) were updated:
  1. Frame - Seat Cushion - Driver Seat (Remove and Replace) - Removed the steps about the seatback shell and the headrest according to the latest validation.
  2. Tire Rotation - Added tire service mileage reset step.
  3. Updated all "Vehicle Electrical Isolation Procedure" references to "Vehicle HV Disablement Procedure".

Week Ending May 18, 2024

The following new procedure(s) were added:
  1. Speaker - Liftgate - LH (Remove and Replace)
The following procedure(s) were updated:
  1. Assembly - Trailer Hitch (Remove and Replace) - Added instructions to prevent corrosion on EU trailer sockets.
  2. Brake Fluid Bleed - One Caliper - Removed steps for running TEST-SELF-VCFRONT_X_BRAKE-FLUID-LEVEL routine.
  3. Jumper Harness - Trailer Hitch (Remove and Replace) - Added instructions to prevent corrosion on EU trailer sockets.
  4. Module - Restraint Control (Non-Structural Pack) (Remove and Replace) - Replaced Toolbox 3 routines by routines using the touchscreen.
  5. Module - Restraint Control (Structural Pack) (Remove and Replace) - Replaced Toolbox 3 routines by routines using the touchscreen.
  6. Service Mode Plus - Added Service Mode Plus activation using the Vehicle Ops App.

Week Ending May 11, 2024

The following procedure(s) were updated:
  1. Glass - Body - Rear Quarter - LH (Remove and Install) - Updated images and added note to apply tape masking tape on the interior of glass to cover exposed areas.
  2. Light - Side Repeater - Front - LH (Remove and Replace) - Updated Toolbox routines for HW4 cameras.

Week Ending May 4, 2024

The following new procedure(s) were added:
  1. Chiller (Heat Pump)(Remove and Replace)
The following procedure(s) were updated:
  1. Lumbar Support - Backrest - Driver Seat (Remove and Replace) - Added a video to show how to remove and install the lumbar support from the seat and fixed the broken links.
  2. Lumbar Support - Back Rest - Front Passenger Seat (Remove and Replace) - Added a video to show how to remove and install the lumbar support from the seat and fixed the broken links.
  3. Sensor - Radar - Front (Calibration) - Added extra info that procedure is not required if no radar is present.
  4. Tire Rotation - Updated instructions on how to reset tire rotation through the vehicle touchscreen, and removed the Toolbox 3 method.

Week Ending April 27, 2024

The following procedure(s) were updated:
  1. Assembly - Filter - HEPA (Remove and Replace) - Fixed erroneous Removal instruction in step 2 of Installation procedure.
  2. Coolant Pump - HV Battery (Dual Motor) (Remove and Replace) - Updated the UI routines.
  3. Coolant Pump - HV Battery (RWD) (Remove and Replace) - Updated the UI routines.
  4. Gearbox Fluid - Rear Drive Unit (3DU) (Drain and Refill) - Updated the description of the o-ring inspection step since the o-ring on the oil fill plug can not be replaced separately.
  5. Lumbar Support - Back Rest - Front Passenger Seat (Remove and Replace) - Removed the steps about the seat assembly and the seat side airbag.
  6. Pyrotechnic Battery Disconnect (Remove and Replace) - Added link to the ancillary bay cover (7-seater).

Week Ending April 20, 2024

The following procedure(s) were updated:
  1. Link - Lateral - Lower - Front - LH (Remove and Replace) - Added instructions for replacing the bolts that attach the front lower lateral link to the subframe on RH side, if not yet replaced.
  2. Links - Lateral - Lower - Front - Pair (Remove & Replace) - Added instruction to mark bolts that attach the front lower lateral link to the subframe with an orange paint mark to identify that the bolts have been replaced by the specified type.
  3. Module - Restraint Control (Structural Pack) (Remove and Replace) - Eliminated redundant ODIN routine and refined instructions on headlight adjustment.
  4. Module - Restraint Control (Non-Structural Pack) (Remove and Replace) - Removed redundant ODIN routine and refined instructions for headlight aiming.
  5. Subframe Assembly - Front (Dual Motor) (Remove and Install) - Added a tool list.
  6. Subframe Assembly - Rear (4DU) (Remove and Replace) - Added a tool list.
  7. Subframe Assembly - Front (RWD) (Remove and Replace) - Updated front lower lateral link to subframe torque specification.

Week Ending April 13, 2024

The following procedure(s) were updated:
  1. 12V/LV Battery (Remove and Replace) - Added a Note to perform the recovery of the LV battery per Toolbox article prior to its replacement.
  2. Filter - Cabin (Remove and Replace) - Updated procedures to accommodate cabin filter covers with top screws and bottom screws.
  3. Fluid Coupling (Straight) - Front Drive Unit (Remove and Replace) - Replace the Toolbox routine by using touchscreen UI.
  4. Gearbox Fluid - Front Drive Unit (Drain and Refill) - Updated gearbox fluid information with link.
  5. Gearbox Fluid - Rear Drive Unit (3DU) (Drain and Refill) - Updated gearbox fluid information with link.
  6. Inverter - Front Drive Unit (Remove and Replace) - Updated gearbox fluid information with link.
  7. Inverter - Rear Drive Unit (3DU) (Remove and Replace) - Updated gearbox fluid information with link.
  8. Oil Pump - Front Drive Unit (Remove and Replace) -
  9. Oil Pump - Rear Drive Unit (3DU) (Remove and Replace) - Updated gearbox fluid information with link.
  10. Desiccant (Remove and Replace) - Added reminding of wearing PPEs.

Week Ending April 6, 2024

The following new procedure(s) were added:
  1. Event Data Recorder Retrieval
The following procedure(s) were updated:
  1. A/C Compressor, Supermanifold and A/C Lines (Remove & Replace) - Fixed bad flush link.
  2. Cover - Ancillary Bay (Remove and Replace) - Added information on installing and removing acillary bay kit insulators.
  3. Car Computer (HW4) (Remove and Install) - Added torque specification for the bolts that attach the car computer to the bulkhead, and added a step for the installation of such bolts.
  4. Fluids and Capacities - Added new Gearbox Fluid section.
  5. Harness - Thermal Beam (Remove and Replace) - Re-structured the procedure and updated the way of performing the routines from using Toolbox to using the touchscreen.
  6. Headlights - Adjust - Global (Wall Method) - Updated measurements and units.
  7. Headlights - Adjust - NA (Wall Method) - Updated measurements and units.
  8. Desiccant (Remove and Replace) - Added reminding of checking the pressure of A/C system before opening the accumulator.