29/09/2024 00:00:26

HV-Batterie (Hinterradantrieb) (Structural Pack) (3-phasig) (R&R) (Ausbauen und Einbauen)

Korrekturcode 16010131 4.14 HINWEIS: Sofern im Verfahren nicht ausdrücklich anders angegeben, spiegeln der obige Korrekturcode und die FRT den gesamten für die Durchführung dieses Verfahrens erforderlichen Aufwand wider, einschließlich der damit verbundenen Verfahren. Schichten Sie keine Korrekturcodes, wenn Sie nicht ausdrücklich dazu aufgefordert werden.HINWEIS: Unter Richtzeiten erfahren Sie mehr über FRTs und wie sie erstellt werden. Für Rückmeldungen zu den FRT-Werten senden Sie bitte eine E-Mail an LaborTimeFeedback@tesla.com. HINWEIS: Siehe Persönlicher Schutz, um sicherzustellen, dass Sie die richtige persönliche Schutzausrüstung tragen, wenn Sie das folgende Verfahren durchführen.

  • 2024-06-13: Updated lift pad adapter PNs.
  • 2023-11-21: Added new lift pad instructions.
  • 2023-11-07: Added references to wade seal procedures.
Special Tools required for this procedure:
  • 1936724-00-A – Universal-Hubkissenadapter
  • 1020566-00-F BGR, Batteriehubtisch, manuell
  • 1065131-00-A Battery Coolant Drain Kit
  • 1108272-00-B Kappe, Logikverbindung, Umr., 3DU
  • 1050448-00-B Coolant Vacuum Refill Tool
  • 1754057-00-A Current Probe, Clamp, DC, 600V
  • 1076927-00-A Hioki Tester
  • 1129166-00-A Hebebühne mit H-Rahmen, EMEA
  • 1133787-00-A Key, Seat Belt Release, Model 3
  • 1134523-00-B Kit, Alignment Rods, Battery, M3
  • 1133843-00-A Kit, Kühlmittel-Ablass- und -Fülladapter, M3
  • 1479505-00-A Kit, M3 Vacuum Fill Coolant Adapter
  • 1135762-00-A Kit, Service-Stecker, Kühlschlauch, Model 3
  • 1637160-00-A MYSP and Palladium Pack Lift Attachment
  • 1076928-00-A Test Probes - Hioki 9461
  • 1080589-00-A Wheel Chocks
Warning IconA warning icon, calling your attention to a possibly risky situation
Warnung

Nur Techniker, die im Umgang mit Hochspannung geschult sind und alle erforderlichen Zertifizierungskurse (falls zutreffend) absolviert haben, dürfen dieses Verfahren durchführen. Beim Umgang mit einem Hochspannungskabel, einer Stromschiene oder eines Hochspannungsanschlusses müssen immer geeignete persönliche Schutzausrüstung (PSA) sowie Isolierhandschuhe mit einer Mindestauslegung von Klasse 0 (1000 V) getragen werden. Weitere Sicherheitsinformationen finden Sie in den Technischen Hinweisen TN-15-92-003, Sorgfaltsregeln beim Umgang mit Hochspannung.

Ausbauen

  1. Remove the LH rocker panel carrier. See Träger – Trittbrett – Links (Ausbauen und Ersetzen).
  2. Remove the butyl patches (x2) that cover the LH rocker access holes.
  3. Montieren Sie Hubkissenadapter.
    • Nur für EMEA: Montieren Sie Adapter, Hubkissen, Model Y (1614078-00-A)
    • Für andere Regionen: Montieren Sie Universal-Hubkissenadapter (1936724-00-A)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warnung
    Verwenden Sie KEINE anderen Hubkissenadapter.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Außerhalb von EMEA ersetzen Universal-Hubkissenadapter (1936724-00-A) Adapter, Hubkissen, Model Y (1614078-00-A). Entsorgen Sie alle anderen Versionen von Hubkissenadaptern.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    In EMEA sind die Universal-Hubkissenadapter noch nicht verfügbar. Stellen Sie sicher, dass Sie die Gummi-Hubkissen für Model Y an Model Y und die Hubkissen für Model 3 an Model 3 verwenden.

    Anweisungen für Universal-Hubkissenadapter:

    1. Montieren Sie abhängig vom Typ der Hebebühne den korrekten Gewindeadapter am Hubadapter.
    2. Stellen Sie sicher, dass die Gewinde-Anschlagscheibe unten am Hubadapter montiert und festgezogen ist. Wenn die Gewinde-Anschlagscheibe nicht montiert ist, fahren Sie nicht mit der Verwendung des Hubadapters fort.
    3. Montieren Sie die Hubadapter an den Hubarmen, sodass das schwarze Hubkissen zum Fahrzeug zeigt.
      Warning IconA warning icon, calling your attention to a possibly risky situation
      Warnung
      Stellen Sie sicher, dass der Adapter in der richtigen Ausrichtung angebracht ist.
    4. Platzieren Sie die Hubarme so, dass die Hubadapter auf das Festpunktloch am Fahrzeug ausgerichtet sind.
    5. Heben Sie die Hubarme an, um die Hubkissen vollständig im Fahrzeug einzusetzen.
    6. Stellen Sie sicher, dass alle 4 Adapter vollständig im Fahrzeug sitzen.
  4. Open all doors and lower the windows.
  5. Release the LH and RH parking brake calipers. See Feststellbremse – Bremssattel - Hinten – LH (Lösen).
  6. Run the Thermal Fill Drain (Coolant Only) routine using the touchscreen. See Kühlsystem (Structural Pack) (Entleeren und Befüllen).
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Select Thermal > Coolant System > Coolant Fill/Drain, then touch Run. Close once the routine is completed.
  7. Remove the seats and the interior carpet from the vehicle. See Teppich – Innenraum komplett (Ausbauen und Ersetzen).
  8. Remove the center console. See Mittelkonsole (2.0) (Strukturpack) (Ausbauen und Ersetzen).
  9. Release the center console harness from the HV battery.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x clip
  10. Remove the bolts (x4) that attach the LH and RH lower IP carrier brackets.
  11. Secure the center seat belt buckles away from the ancillary bay.
  12. Remove the rear inner HV battery bolts (x4).
  13. Push the vehicle onto a 2-post lift.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Assistance recommended. Note that this vehicle can only be safely pushed for a very short distance and at very slow speed.
  14. Raise and support the vehicle. See Fahrzeug heben - Zweisäulenhebebühne.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Verify jack locations prior to lifting vehicle, ONLY place on lifting points at front and rear of rocker panels
  15. Raise vehicle fully and lower the lift onto locks.
  16. Remove the front aero shield panel. See Verkleidung – Windabweiser – Vorne (Strukturpack) (Ausbauen und Ersetzen).
  17. Pull the RH front wheel liner away from the HV battery.
  18. Pull the LH front wheel liner away from the HV battery.
  19. Remove the mid aero shield panel. See Verkleidung – Windabweiser – Mitte (Ausbauen und Ersetzen).
  20. Führen Sie das HV-Abschaltverfahren aus. Siehe HV-Abschaltverfahren des Fahrzeugs (Strukturpack).
  21. Lower the vehicle until the tires are touching the ground.
  22. Release the 2nd row 60 seat connector from the LH seat frame.
  23. Disconnect the 3-phase connector from the HV battery.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Release locking tab upwards then lift up the connector.
  24. Remove the bolt that attaches the busbar cover access door.
  25. Remove the bolts that attach the charge port busbar kit to the HV header.
  26. Release the LH body harness from the rear body and move it aside.
  27. Lift the busbar kit connector to remove it from the HV header.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Use an inflatable airbag to suspend the busbar away from the HV header during removal and installation. Hold busbar firmly as there is tension on it.
    F
    F
  28. Disconnect the HVC logic connector and install the logic cap.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Release the locking tab, then pivot the handle downward to release connector.
  29. Disconnect the LV power connector from the HV battery.
  30. Close all doors.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Latch the rear doors to prevent accidental closure.
  31. Raise the vehicle to a comfortable working height.
  32. Position a coolant drain container underneath the LH front of the HV battery.
  33. Disconnect the PT supply hose at the LH front side of the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Plug the hose connections.
  34. Position the coolant drain container underneath the LH RDU area.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Position neck to catch all coolant loss.
  35. Release the RDU inverter inlet hose from the RDU.
  36. Disconnect the RDU inverter inlet hose from the fluid coupling.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Plug the drive unit coupling.
  37. Position the coolant drain container underneath the front left manifold battery supply hose.
  38. Disconnect the front left manifold battery supply hose.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Plug hose connections.
  39. Position the coolant drain container underneath the RH front of the HV battery.
  40. Disconnect the HV battery RH front inlet hose.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Plug hose connections.
  41. Release the clip that attaches the HV battery RH front inlet hose to the skid plate.
  42. Position the coolant drain container underneath the RH front of the HV battery.
  43. Disconnect the PT return hose at the RH front side of the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Plug hose connections.
  44. Release the clip that attaches the PT return hose to the RH front side of the HV battery pack.
  45. Release the PT coolant hose from the LH side of the front HV battery bash plate.
  46. Position the coolant drain container underneath the LH rear side of the HV battery.
  47. Remove the RDU inverter inlet hose.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Rotate the hose between the subframe and battery out of the vehicle.
  48. Disconnect the compressor HV harness from the HV battery.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Hold down the red locking tab, and the disengage the release lever. Do not force the release lever up.
  49. Release the clips (x4) that attach the compressor HV harness to the HV battery.
  50. Release the RDU oil cooler outlet pipe.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Plug hose connections.
  51. Remove the RDU oil cooler outlet pipe.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Rotate the pipe down over the RDU and rearward around the subframe.
  52. Remove the coolant drain container from underneath the vehicle.
  53. Release the RDU HV cable bracket from the RDU.
  54. Disconnect the RDU HV cable from the RDU.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Release the locking tab, and then rotate the release lever up to disengage the connector. Do not force the release lever up.
  55. Remove the RDU HV cable.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Rotate the cable underneath the logic cable harness between the subframe and the HV battery.
  56. Remove the smaller bolts of the LH and RH shear plates.
  57. Loosen the large bolt that attaches the LH shear plate and subframe to the body and rotate the shear plate clear of the HV battery.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Hand tighten the bolt once the shear plate is in position.
  58. Loosen the large bolt that attaches the RH shear plate and subframe to the body and rotate the shear plate clear of the HV battery.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Hand tighten the bolt once the shear plate is in position.
  59. Put the battery table into position and lower vehicle to support the battery.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Assistance is recommended. Line up the table so the bolts at the front bash plate are accessible and the rear HV cables are accessible. Adjust the final battery table position using adjustable caster jacks on the table.
  60. Loosen the front bolts that attach the HV battery through the skid plate cover with ratchet, and then remove them with a battery powered drill.
  61. Loosen the bolts that attach the skid plate to the vehicle with a ratchet, and then remove them with a battery powered drill.
  62. Loosen the bolts that attach the rear HV battery to the vehicle with a ratchet, and then remove them with a battery powered drill.
  63. Loosen the LH bolts that attach the HV battery to the vehicle with a ratchet, and then remove them with a battery powered drill.
  64. Loosen the RH bolts that attach the HV battery to the vehicle with a ratchet, and then remove them with a battery powered drill.
  65. Raise the vehicle to free it from the HV battery.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Assistance is recommended.
  66. Remove the battery from under the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Assistance is recommended.

Montieren

Informational PurposesAn informational icon, calling your attention
Anmerkung
Ist eines der Gewinde im vorderen (FUB) oder im hinteren Unterboden-Gussteil (RUB) beschädigt, siehe TN-15-92-001 – Helicoil-Einsätze einbauen, um Reparaturanweisungen zu Helicoil-Einsätzen zu erhalten.
Warning IconA warning icon, calling your attention to a possibly risky situation
ACHTUNG
Verwenden Sie für Reparaturen im FUB oder im RUB ausschließlich Helicoil-Einsätze mit der Tesla-Teilenummer 1056157-09-A.
Informational PurposesAn informational icon, calling your attention
Anmerkung
Wenn eine Gewindereparatur ausgeführt wurde, fügen Sie Reparaturcode 70060005 – Gewindereparatur als separate Aktivität zum Servicebesuch hinzu.
  1. Inspect and clean the wade seal on the HV battery prior to installation.
    If the wade seal is damaged, rework or replace the seal.
  2. Clean the HV connector contact surface of any residual Penetrox.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Allow 1 minute dry time after removing Penetrox. New busbar comes with Penetrox applied to the HV connector.
  3. Clean the busbar HV connector contact surface of any residual Penetrox.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Allow 1 minute dry time after removing Penetrox. It is necessary to clean the HV connector during re-use of the busbar.
  4. Apply Penetrox onto the HV connector joints.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Apply 2 drops of Penetrox A-13 about 5mm in diameter to either side of the hole on both leads. Spread evenly to ensure that the contact surface is fully covered.
  5. Install the HV battery alignment rods (x2) onto the body.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Only use the smaller rods. Thread onto RH front most and LH rear most side holes.
  6. Position the HV battery pack under the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Assistance is recommended.
  7. Carefully lower the vehicle onto the HV battery pack and align the battery holes with the rods.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Assistance is recommended. Make sure that coolant hoses and harnesses do not get pinched.
  8. Remove the HV battery alignment rods from the body once the HV battery is aligned.
  9. Thread in by hand all bolts that attach the HV battery to the vehicle. Do not install bolts to the shear plates yet.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    34x bolts. Includes top bolts. Start with bolts nr. 35-36-37-38 Ensure smooth thread engagement and bolts are not cross threaded into the casting.
  10. Completely lower the vehicle onto the battery pack.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Assistance is recommended.
  11. Seat all bolts (x34) that attach the HV battery to the vehicle with a battery powered drill.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Ensure smooth thread engagement and bolts are not cross threaded into the casting. Flush down the bolts. Do not over tighten bolts, fully torque them at later steps.
  12. Fully torque the LH bolts (x7) that attach the HV battery to the vehicle (torque 56 Nm).
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Bolt position 1-7.
  13. Fully torque the RH bolts (x7) that attach the HV battery to the vehicle (torque 56 Nm).
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Bolt position 16-22.
  14. Fully torque the rear bolts (x4) that attach the HV battery to the vehicle (torque 62 Nm).
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Bolt position 10-13.
  15. Fully torque the front bolts (x6) that attach the HV battery through the bash plate openings (torque 90 Nm).
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Later production vehicles have E14 bolts torqued at 75 Nm. Bolt location 23 to 28.
  16. Fully torque the front bolts (x6) that attach the bash plate to the vehicle (torque 62 Nm).
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Bolt location 29-34.
  17. Loosen the RH rear subframe bolt and align the RH rear shear plate with the HV battery.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Hand tighten bolt once the shear plate is in position.
  18. Install the bolts that attach the RH shear plate to the HV battery hand tight.
  19. Torque the large bolt that attaches the subframe and RH rear shear plate to the body (torque 130 Nm).
  20. Torque the 2 smaller bolts that attach the RH rear shear plate to the body (torque 62 Nm).
  21. Repeat steps 42 through 45 on the LH side of the vehicle.
  22. Open the LH rear door.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Use caution while working around this area not to damage any components.
  23. Fully torque the LH rear inner bolts (x2) that attach the HV battery pack to the vehicle (torque 49 Nm).
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Bolt position 35-36.
  24. Visually inspect the wade seal to make sure that no gaps are present.
  25. Close LH rear door.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Do not latch the door.
  26. Open the RH rear door.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Use caution while working around this area not to damage any components
  27. Fully torque the RH rear inner bolts that attach the HV battery pack to vehicle (torque 49 Nm).
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Bolt position 37-38.
  28. Close RH rear door
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Do not latch the door.
  29. Raise vehicle and lower onto locks, then remove the battery table from under the vehicle.
  30. Position the RDU HV cable up to the RDU.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Rotate cable underneath logic cable harness between subframe and HV battery.
  31. Connect the RDU HV cable onto the RDU.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Verify lever is in the upright and open position, then carefully seat connector and allow the lever to engage. Fully secure lever and verify red tab is locked. Do not damage any pins.
  32. Secure the RDU HV harness onto the HV battery.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Verify lever is in the upright and open position, then carefully seat the connector and allow the lever to engage. Fully secure the lever and verify that the red tab is locked. Do not damage any pins.
  33. Install the bolt that attaches the RDU HV cable bracket to the RDU (torque 6 Nm).
  34. Install the RDU oil cooler outlet pipe.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Rotate up over the RDU and rearward around the subframe to oil cooler.
  35. Attach the RDU oil cooler outlet pipe.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x spring clips, 5x clips. Remove plugs as needed
  36. Attach the compressor HV harness to the HV battery.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    4x clips
  37. Connect the compressor HV harness onto the HV battery.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Verify that the lever is in the upright and open position, then carefully seat the connector and allow the lever to engage. Fully secure lever and verify that the red tab is locked.
  38. Install the RDU inverter inlet hose.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x spring clip, 1x clip. Rotate between subframe and battery into the RDU and PCS outlet. Remove plugs as needed.
  39. Attach the RDU inverter inlet hose to the RDU HV cable.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x clip
  40. Install the mid aero shield panel. See Verkleidung – Windabweiser – Mitte (Ausbauen und Ersetzen).
  41. Position a coolant drain container underneath the LH front of the HV battery.
  42. Connect the PT supply hose at the LH front side of the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x spring clip. Remove plugs as needed.
  43. Attach the PT coolant hose onto the LH side of the front HV battery bash plate.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x clip
  44. Position the coolant drain container underneath the RH front of the HV battery.
  45. Connect the PT return hose at the RH front side of vehicle.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x spring clip. Remove plugs as needed.
  46. Attach the PT return hose to the RH front side of the HV battery pack.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x clip
  47. Connect the HV battery RH front inlet hose.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x spring clip. Remove plugs as needed.
  48. Attach the HV battery RH front inlet hose to the skid plate.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x clip
  49. Position the coolant drain container underneath the front left manifold battery supply tube.
  50. Connect the front left manifold battery supply tube.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x spring clip, 1x clip. Remove plugs as needed.
  51. Remove the coolant drain container from underneath the vehicle.
  52. Release the LH front wheel liner from the bungee strap.
  53. Release the RH front wheel liner from the bungee strap.
  54. Install the front aero shield panel. See Verkleidung – Windabweiser – Vorne (Nicht Strukturpack) (Ausbauen und Ersetzen).
  55. Fully lower the vehicle, and then push the vehicle away from the lift.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Assistance is recommended. Place wheel chocks to prevent the vehicle from moving. Note that this vehicle can only be safely pushed for a very short distance and at very slow speed.
  56. Open all doors
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Latch rear doors to prevent accidental closure
  57. Connect the LV power connector to the HV battery.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Push the red locking tab down to secure the connection.
  58. Remove the HVC logic cap, and then connect HVC logic connector.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Pivot the handle upward to engage the connector and secure the locking tab.
  59. Position the busbar kit connector and lower it onto the HV header.
  60. Install the bolts (x2) that attach the charge port busbar kit to the HV Header (torque 9 Nm).
  61. Put on HV insulating gloves and leather over gloves.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Check gloves for damage and expiry details. Refer to Service Document TN-15-92-003 for further details.
  62. Perform a Hioki resistance test at each HV joint from HV busbar lead to bolt head.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    The acceptable resistance is between 0.050 mΩ (50 μΩ) and 0.195 mΩ (195 μΩ). If the resistance is greater than 0.195 mΩ (195 μΩ), there is too much resistance in the High Voltage joint. Remove the fastener, clean areas with isopropyl alcohol, install fastener back and test again. If the resistance is lower than 0.050 mΩ (50 μΩ), reposition the probes and measure again. If the resistance is repeatedly between 0.00 mΩ and 0.050 mΩ (50 μΩ), the Hioki test passed; proceed to the next step.
  63. Remove leather over gloves and HV insulating gloves.
  64. Install the bolt that attaches the busbar cover access door (torque 9 Nm).
  65. Install the LH body harness onto the rear body.
  66. Connect the 3-phase connector onto the HV battery.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Pivot the handle downwards to engage the connector and secure the locking tab.
  67. Attach the 2nd row 60 seat connector to the LH seat frame.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x clip.
  68. Remove the tape from the seat frame.
  69. Install the bolts (x4) that attach the LH and RH lower IP carrier brackets (torque 25 Nm)..
  70. Install the center console harness to the HV battery.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x clip.
  71. Install the center console. See Mittelkonsole (2.0) (Strukturpack) (Ausbauen und Ersetzen).
  72. Install the seats and the interior carpet to the vehicle. See Teppich – Innenraum komplett (Ausbauen und Ersetzen).
  73. Perform a vacuum refill of the cooling system. See Kühlsystem (Vakuumbefüllung).
  74. Connect LV power. See 12-V-/Niederspannungsversorgung (Trennen und Verbinden).
  75. Press and hold the Park button to exit EPB service mode.
  76. Access the thermal system routines using the UI: Select Quick Controls (vehicle icon) > Service Mode > Thermal > Actions.
  77. Unlock the vehicle gateway. See Gateway (Entriegeln).
  78. Perform a coolant purge from the touchscreen.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Touch time only. Wait until coolant pumps stop running (audible noise), "Routine Passed" appears, but pumps will run for 10 minutes. If you start another routine during this time, it will fail. Make sure vehicle is not in "Drive". Routine is still running despite the completed message. Speeds can be monitored in garage under PT Thermal tab, Idle speed = ~1500 RPM. The rest will vary speeds from 3500-6500 RPM and actuate valves between SERIES and PARALLEL. Putting the vehicle into "Drive" will stop this routine. If speeds hover at 7000 RPM, this indicates the pumps are air locked; perform a vacuum fill. Continue to add coolant and purge until the coolant level reaches between the NOM and MAX Lines on the bottle.
  79. Inspect the coolant level at the reservoir and top off as necessary.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Ensure coolant is filled using G-48 coolant.
  80. Install the coolant bottle cap.
  81. Perform the Thermal Performance Test using the touchscreen: touch Thermal > Actions > Test Thermal Performance > Start, touch Run and allow the routine to complete.
  82. Exit Service Mode through the touchscreen.
  83. Install the HEPA filter assembly. See Baugruppe – Filter – HEPA (Ausbauen und Ersetzen).
  84. Install the rear underhood apron. See Unterhaubenschürze – Hinten (Ausbauen und Ersetzen).
  85. Remove the lift pad adapters from LH and RH rocker panel.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x lift pad adapters per side.
  86. Install butyl patches onto the LH and RH rocker panel access holes.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x butyl patches per side. Apply pressure along patch to verify it is fully secured to body. Use new butyl patches if needed, Roughly 2" x 2 1/2"
  87. Install the LH and RH rocker panel carrier. See Träger – Trittbrett – LH (Strukturpack) (Ausbauen und Ersetzen).
  88. Install the LH and RH rocker panel covers onto the rocker panel carrier. See Abdeckung – Trittbrettformteil – Unten – LH (Ausbauen und Ersetzen).