11/02/2024 07:30:54

侧中继摄像头 - 前 - LH (HW4)（拆卸和更换）

校正代码 17221302 0.18 注意：除非本程序中另有明确规定，否则上述校正代码和 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。 注意：请参阅平均维修工时，深入了解 FRT 及其创建方式。要提供有关 FRT 值的反馈，请发送电子邮件至LaborTimeFeedback@tesla.com。 注意：执行下述程序时，请参阅人员保护确认已穿戴适当的个人防护装备 (PPE)。

2024-02-05: 添加了“包裹摄像头和电气线束的端子，以防其与水或其他可能导致损坏的溶液接触”的注意事项。
2023-04-19: Added HW4 camera connection test steps.

拆卸

警告

尽管此程序已经过验证，但仍是一个草案。可能没有警告和注意事项。请遵守安全要求，处理或靠近高压系统和部件时，请谨慎操作。请将校正修理内容及反馈发送至ServiceDevelopment@teslamotors.com。

Open the LH front door.
Lower the LH front window.
Press the brake pedal to turn on the drive rails.
Use the center display to set the air suspension ride height to “Very High”.
Turn the steering wheel fully to the left.
Enable service mode. See 维护模式（启用和禁用）.
Apply masking tape to the LH front fender assembly at the edges of the LH front side repeater.
提示：推荐使用以下工具：
- Masking tape
Release the clips (x3) that attach the rear portion of the LH front fender garnish to the LH rocker panel molding.
提示：推荐使用以下工具：
- Plastic trim tool
Partially remove the rear portion of the LH front wheel arch liner.

注
Carefully fold the wheel arch liner downwards and away from the fender to gain access to the side repeater assembly.
Release the push clip that attaches the LH front side repeater to the LH front fender assembly.

注
Push the repeater locator tab to release the repeater from the fender, guide the locator tab to clear the fender, and then remove the repeater from the fender.
Disconnect the LH front side repeater connectors (x2).

注
Press down on the lock release and pull the connector away from the side repeater camera. Release the red locking tab and press down to disconnect the side repeater connector.

警告
包裹摄像头和电气线束的端子，以防其与水或其他可能导致损坏的溶液接触。
Remove the LH front side repeater from the vehicle.
Remove the bolts (x2) that attach the LH front side repeater camera to the repeater assembly, and then remove the camera from the repeater assembly.

注
Remove the bolts and then wiggle the camera to clear the o-ring from the repeater assembly.

安装

Position the LH front side repeater camera on the repeater assembly, and then install the bolts (x2) that attach the camera on the repeater assembly.

注
Wiggle the camera o-ring through the repeater assembly, and then install that bolts that attach the camera to the repeater assembly.
Connect the LH front side repeater connectors (x2).

注
Remove the tape first, if present.

注
Secure the side repeater connectors, and then engage the red locking tab on the side repeater connector.
重置辅助驾驶系统 (DAS)。
1. 解锁车辆网关。请参阅网关（解锁）。
2. 在触摸屏“维护模式”菜单中，点击Driver Assist > Cameras > Reset DAS。
3. 在触摸屏“摄像头”图示中，确认Reset DAS按钮呈绿色高亮以及所有辅助驾驶系统 (DAS) 部件显示绿色状态灯。
  
  注
  检查并修正所有显示红色状态灯的辅助驾驶系统 (DAS) 部件。
仅限 HW4 摄像头：运行摄像头连接测试以更新新装摄像头的固件。

注
辅助驾驶系统 (DAS) 摄像头并非 CAN 总线模块，无法通过固件重装或“零件更换部署”进行更新。
1. 将本地装有 Toolbox 3 的笔记本电脑与车辆相连。请参阅Toolbox 3（连接和断开）。
2. 点击Actions选项卡，搜索 “calibration mode”，然后点击Run，以运行DAS Enter Calibration Mode例行程序。
3. 点击Actions选项卡，搜索 “camera connection test”，然后点击Run，以运行与所更换摄像头对应的例行程序（例如Left B-Pillar Camera Connection Test或Front Camera Connection Test）。
  
  注
  前置双摄像头总成包含两个单独的摄像头，必须独立更新：Front Camera Connection Test和Fisheye Camera Connection Test。请务必更新所更换摄像头的固件。
  
  注
  如果同一例行程序显示有两个版本，请点击Run运行 “Path” 字段中包含 “-SCRIPT” 的例行程序。
4. 在 “Camera Connection Test” 提示中，将 “Timeout” 更改为 “100”，然后点击Run运行该例行程序。
  
  注
  此例行程序将更新摄像头固件，并确认摄像头已连接。
Install the push clip that attaches the LH front side repeater to the LH front fender assembly.

注
Ensure the repeater tabs (x2) are intact and installed in place correctly.
Remove the masking tape from the LH front fender assembly at the edges of the LH front side repeater.
Push the rear portion of the LH front wheel arch liner back to original position.

注
Ensure the liner aligns with the fender correctly.
Install the clips (x3) that attach the rear portion of the LH front fender garnish to the LH rocker panel molding.

注
Carefully secure the garnish and fully engage the clips.
Press the brake pedal to turn on the drive rails.
Turn the steering wheel to the center.
Use the center display to set the air suspension ride height to “Medium”.
Disable service mode. See 维护模式（启用和禁用）.
Raise the LH front window.
Close the LH front door.