Current Release Notes

Archived Release Notes:

Week Ending December 21, 2024

The following procedure(s) were updated:
  1. Compressor (Remove and Replace) - Added Notes on separately adding correction code 18200102.
  2. Condenser - Sub-Cool - RH (Remove and Replace) - Added Note on separately adding correction code 18200102.
  3. Fan - Condenser - RH (Remove and Replace) - Added Note on separately adding correction code 18200102.
  4. Pipe - High Pressure - Charge Port (Remove and Replace) - Added Note on separately adding correction code 18200102.
  5. Pipe - High Pressure - Compressor to Condenser (Remove and Replace) - Added Note on separately adding correction code 18200102.
  6. Pipe - High Pressure - Compressor to Condenser (Dual Motor) (Remove and Replace) - Added Note on separately adding correction code 18200102.
  7. Pipe - High Pressure - Gas Cool to Sub-Cool Condenser (Remove and Replace) - Added Note on separately adding correction code 18200102.
  8. Pipe - High Pressure - Sub-Cool Condenser to Chiller (Remove and Replace) - Added Note on separately adding correction code 18200102.
  9. Pipe - Low Pressure - Charge Port (Remove and Replace) - Added Note on separately adding correction code 18200102.
  10. Sensor - Pressure and Temperature - High Pressure (Remove and Replace) - Added Note on separately adding correction code 18200102.
  11. Sensor - Pressure and Temperature - Low Pressure (Remove and Replace) - Added Note on separately adding correction code 18200102.
  12. TXV Valve - Chiller (Remove and Replace) - Added note on separately adding CC 18200102.
  13. TXV Valve - Evaporator (Remove and Replace) - Added Note on separately adding correction code 18200102.

Week Ending December 14, 2024

The following new procedure(s) were added:
  1. New glass components (windshield, roof, door, and fixed glass) must be inspected before installation to meet Tesla’s internal standards of quality. The Pre-Installation Glass Inspection procedure explains how to inspect new windshield, roof, door, and fixed glass components before the new component is installed.
The following procedure(s) were updated:
  1. Added a new caution about Pre-Installation Glass Inspection service requirements:
  2. Base Assembly - Driver Seat (Model X Seat) (Remove & Replace) - Added mini-tilt motor configuration information.
  3. Base Assembly - Front Passenger's Seat (Remove and Replace) - Added mini-tilt motor configuration information.
  4. Frame Assembly - Cushion - Driver Seat (Remove and Replace) - Added mini-tilt motor configuration information.
  5. Halfshaft Assembly - Rear - LH (Remove and Replace) - Added tips on the installation order of parts.
  6. Motor - Seat Tilt - Driver's Seat (Remove and Replace) - Added mini-tilt motor configuration information.
  7. Removed note to add 00040100. FRT now includes test drive.

Week Ending December 7, 2024

The following procedure(s) were updated:
  1. Control Arm - Upper - Front - LH (1st Generation) (RHD) (RWD) (Remove and Replace) - Added info on FUCA ride height tool for EMEA.
  2. Control Arm - Upper - Front - LH (Remove and Replace) - Added info on FUCA ride height tool for EMEA.
  3. Control Arm - Upper - Front - RH (1st Generation) (RWD) (Remove and Replace) - Added info on FUCA ride height tool for EMEA.
  4. Link - Fore - Lower - Front - LH (Remove and Replace) - Added info on FUCA ride height tool for EMEA.
  5. Links - Fore - Lower - Front - LH/RH (Remove and Replace) - Added info on FUCA ride height tool for EMEA.
  6. Seat Assembly - 1st Row - LH (Remove and Replace) - Added configuration information for seat assemblies with the mini-tilt motor.
  7. Seat Assembly - 1st Row - RH (Remove and Replace) - Added configuration information for seat assemblies with the mini-tilt motor.
  8. Wiper Module (Remove and Replace) - Updated procedure to latest procedure validation.

Week Ending November 30, 2024

The following procedure(s) were updated:
  1. Cooling System - Vacuum Refill - Added images of vacuum refill tool setup and added warning on incorrect use of the refill tool.

Week Ending November 23, 2024

The following procedure(s) were updated:
  1. Battery - Auxiliary - 12V (Remove and Replace) - Added a note to remind of checking the 12V/LV battery temperature before performing the procedure.

Week Ending November 16, 2024

The following new procedure(s) were added:
The following procedure(s) were updated:
  1. Steering Rack (LHD RWD) (1st Generation) (Remove and Replace) - Updated firmware install step.
  2. Steering Rack (LHD Dual Motor) (1st Generation) (Remove and Replace) - Updated firmware install step.
  3. Steering Rack (RHD RWD) (1st Generation) (Remove and Replace) - Updated firmware install step.
  4. Steering Rack (RHD Dual Motor) (1st Generation) (Remove and Replace) - Updated firmware install step.

Week Ending November 2, 2024

The following new procedure(s) were added:
  1. Media Control Unit (Dispose)
  2. Windshield Chip Repair (EMEA)
The following procedure(s) were updated:
  1. DCDC Converter (Remove and Replace) - Updated removal section to latest validation and revamped installation steps.
  2. Media Control Unit (Remove and Replace) - Added disposal instructions to procedure.

Week Ending October 26, 2024

The following new procedure(s) were added:
  1. Module - Autopilot - ECU (Dispose)
The following procedure(s) were updated:
  1. Clear Forward Camera View (Precision Cleaning Of Inboard Windshield) - Added a video demonstrating precision cleaning of windshield.
  2. Integral Link - Rear - LH (Remove and Replace) - Added ride height setting steps to Installation section.
  3. Module - Autopilot - ECU - 2nd and 3rd Generation (Remove and Replace) - Added step on Autopilot ECU disposal.
  4. Sensor - Ride Height - Front - LH (Retrofit) - Added RH front ride height sensor harness image for clarity purposes.