09/10/2024 22:59:53

Clean Radiator

Correction code 18301000 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See to make sure proper PPE is worn when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT, although it has been validated. Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.
  1. Open the LH front door.
  2. Lower the LH front window.
  3. Activate Service Mode using the touchscreen.
  4. Press brake pedal to turn on drive rails
  5. Set air suspension ride height to “Very High”
    Informational PurposesAn informational icon, calling your attention
    Note
    Via center display > Controls > Suspension > ''Very High''
  6. Turn steering wheel fully to the right
  7. Open the hood.
  8. Remove the rear underhood apron.
  9. Remove the LH underhood apron.
  10. Remove the RH underhood apron.
  11. Remove the front underhood apron.
  12. Remove the underhood storage unit access panel.
  13. Remove the underhood storage unit carpet.
  14. Remove the underhood storage unit from the vehicle.
  15. Remove bolts securing upper portion of front fascia
    Informational PurposesAn informational icon, calling your attention
    Note
    6x bolts, 10mm, 7 Nm
  16. Remove fasteners securing LH front wheel liner to valence
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, T30, 1.5 Nm, 3x clips, Move front portion of wheel liner backwards to access fairing
  17. Remove LH front wheel fairing from valence
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 10mm, 1.5 Nm, 1x securing tab
  18. Partially remove front portion of LH front fender garnish
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips, 8x tabs, Careful to not damage dummy ultra sonic sensor when removing garnish
  19. Remove bolt securing LH front of fascia to LH front fender
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 8mm, 1.5 Nm
  20. Press brake pedal to turn on drive rails
  21. Turn steering wheel fully to the left
  22. Remove clips securing RH front wheel liner to valence
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips, Move front portion of wheel liner backwards to access fairing
  23. Remove RH front wheel fairing from valence
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 10mm, 1.5 Nm, 1x securing tab
  24. Partially remove front portion of RH front fender garnish
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips, 8x tabs, Careful to not damage dummy ultra sonic sensor when removing garnish
  25. Remove bolt securing RH front of fascia to RH front fender
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 8mm, 1.5 Nm
  26. Power off the vehicle using the touchscreen.
  27. Disconnect the LV battery connector and First Responder Loop.
  28. Remove fasteners securing lower portion of front fascia to valence
    Informational PurposesAn informational icon, calling your attention
    Note
    3x bolts, 10mm, 3 Nm, 2x clips
  29. Apply masking tape to protect LH and RH front fenders
  30. Disconnect front fascia assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connectors, Release locking tabs then disconnect
  31. Remove front fascia assembly from vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend assistance, Release fascia from LH and RH fender brackets, Careful not to damage the fender bracket when removing fascia, Place on protected surface to avoid damage
  32. Disconnect active grille shutter actuator
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector, Release locking tab
  33. Disconnect ambient air sensor and push grommet through front end carrier
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector, 1x grommet
  34. Remove ambient temperature sensor from active grill shutter assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, Squeeze retaining arms on clip and remove downward
  35. Release locking tabs securing active grille shutter to cooling fan module assembly and remove active grille shutter through front of vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    12x locking tabs, 2x clips
  36. Remove plastic grille from the radiator
    Informational PurposesAn informational icon, calling your attention
    Note
    9x locking tabs
  37. Use shop-vac to clean dirt on the radiator
    Informational PurposesAn informational icon, calling your attention
    Note
    If necessary removeal large debris
  38. Use blow gun to clean dirt on the radiator again
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not get too close to the radiator blades
  39. Install plastic grille to the radiator
    Informational PurposesAn informational icon, calling your attention
    Note
    9x locking tabs
  40. Install active grille shutter to cooling fan module assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    12x locking tabs, 2x clips, Align datums before engaging tabs, Make sure shutter slides inside tab not outside
  41. Install ambient temperature sensor into active grill shutter assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, 1x datum, Align datum with opening in active grill shutter assembly
  42. Connect ambient air sensor and secure grommet onto active grille shutter
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector, 1x grommet
  43. Connect active grille shutter actuator
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector, Engage locking tab
  44. Connect front fascia harness onto frunk harness
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connectors, Engage locking tab, Located behind RH wheel arch liner
  45. Install front fascia onto vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend assistance, Slide LH and RH side of fascia into fenders, Careful not to damage the fender bracket when installing fascia
  46. Install fasteners securing lower portion of front fascia to valence
    Informational PurposesAn informational icon, calling your attention
    Note
    3x bolts, 10mm, 3 Nm, 2x clips
  47. Remove masking tape from front fenders
  48. Install bolt securing fascia to RH fender bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 8mm, 5 Nm
  49. Install RH front fender garnish
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips, 8x tabs, Secure from top to bottom of front bumper
  50. Install RH front wheel fairing to valence
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 10mm, 1.5 Nm
  51. Install push clips securing RH front wheel liner onto fascia
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips
  52. Connect the First Responder Loop and LV battery connector.
  53. Press brake pedal to turn on drive rails
  54. Turn steering wheel fully to the right
  55. Install bolt securing fascia onto LH fender bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 8mm, 5 Nm
  56. Install LH front fender garnish
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips, 8x tabs, Secure from top to bottom of front bumper
  57. Install LH front wheel fairing to valence
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 10mm, 1.5 Nm, 1x securing tab
  58. Install fasteners securing LH front wheel liner to valence
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, T30, 1.5 Nm, 3x clips
  59. Install bolts securing upper portion of front fascia
    Informational PurposesAn informational icon, calling your attention
    Note
    4x bolts, 10mm, 7 Nm, Ensure proper fascia-to-headlamp gap and flushness
  60. Install the underhood storage unit.
  61. Install the underhood storage unit carpet.
  62. Install the underhood storage unit access panel.
  63. Install the front underhood apron.
  64. Install the LH underhood apron.
  65. Install the RH underhood apron.
  66. Install the rear underhood apron.
  67. Close the hood.
  68. Unlock Gateway
    Informational PurposesAn informational icon, calling your attention
    Note
    After vehicle has been put into "Service Mode", place keycard on center console to turn on drive rails, hold down the brake pedal, while keep pressing right hand signal button simultaneously for at least 10 seconds, "GTW UNLOCKING" should pop up on the UI right next to the VIN during these 10 seconds, once gateway is unlocked "GTW UNLOCKED 5400" will be displayed on the UI next to the VIN, the gateway will remain unlocked for 90 minutes, follow steps on Toolbox article #5582900 for any additional information
  69. Perform Thermal Performance via Service UI
    Informational PurposesAn informational icon, calling your attention
    Note
    Select Thermal > Actions > Test Thermal Performance, click Run, close once routine is completed
  70. Perform HVAC Performance via Service UI
    Informational PurposesAn informational icon, calling your attention
    Note
    Select Thermal > Actions > Test HVAC Performance, click Run, close once routine is completed
  71. Run ODIN routine PROC_ICE_X_EXIT-SERVICE-MODEvia Toolbox: (link)
  72. Calibrate the RH falcon wing door.
  73. Calibrate the LH falcon wing door.
  74. Turn steering wheel back to center
  75. Set air suspension ride height to Medium
    Informational PurposesAn informational icon, calling your attention
    Note
    Using center display > Suspension > Medium/Standard
  76. Raise the LH front window.
  77. Close the LH front door.