Release Notes April-June 2023

Archived Release Notes:

Week Ending July 1, 2023

The following procedure(s) were updated:
  1. DCDC Converter - 2nd Generation (Retrofit) - Added Cautions and Tips to prevent swapping of the FJB logic connector (X040) and the DCDC logic connector (X041).
  2. Key Fob - Program - Removed obsolete security update procedure.
  3. Power Strut - Liftgate (Remove and Replace) - Added steps to calibrate the liftgate to the closed position.
  4. Fascia Assembly - Front (Remove and Replace) - Added steps for vehicles built after April 10, 2016.

Week Ending June 24, 2023

The following procedure(s) were updated:
  1. Calibration - Front Radar Sensor - Replaced steps for the Toolbox 3 Tools tab.
  2. Electromechanical Brake Booster Assembly (Remove and Replace) - Replaced steps for the Toolbox 3 Tools tab.
  3. HV Rapid Mate Vehicle Side (Remove and Replace) - Added step to remove the plastic cover from the cables before removal of the assembly.
  4. SRS Inspection and Component Replacement -
  5. Subframe Assembly - Rear (Remove and Install) - Updated note for replacement of seized rear drive unit HV harness.

Week Ending June 10, 2023

The following new procedure(s) were added:
  1. Hose - Outlet - Rear Drive Unit (Remove and Replace)
The following procedure(s) were updated:
  1. DCDC Converter - 2nd Generation (Retrofit) - Revised step 29 of section "Retrofit the Forward Junction Box" to use the existing vehicle ground harness, and added part number to the "parts required" table.
  2. HV Battery (RWD/AWD) (Remove and Replace) - Service Engineering updates to the touchscreen steps.
  3. Wheel Assembly (Remove and Install) - Added tightening torque to installation section.

Week Ending June 03, 2023

The following new procedure(s) were added:
  1. Blower Control FET Assembly - Blower Motor - HVAC (RHD) (Remove and Replace)
The following procedure(s) were updated:
  1. Module - Steering Column Control (Remove and Replace) - Added step to set Gateway configuration for "steeringWheel" for pre-2015 MY vehicles.
  2. Tire - Front - LH (Remove and Replace) - Added caution about lubricant drying time.

Week Ending May 27, 2023

The following new procedure(s) were added:
  1. Charge Port Voltage Check
The following procedure(s) were updated:
  1. Charge Port - 3 Phase (Remove and Replace) - Updated procedure to use Charge Port Voltage Check.
  2. Charge Port - Manual Release of Cable - Updated procedures to use Charge Port Voltage Check.
  3. Charge Port - Single Phase - Motorized (Remove and Replace) - Updated procedure to use Charge Port Voltage Check.
  4. Charge Port - Single Phase - Non-Motorized - Manual Release of Cable - Updated procedure to use Charge Port Voltage Check.
  5. Charge Port - Single Phase - Non-Motorized (Remove and Replace) - Updated procedure to use Charge Port Voltage Check.
  6. Control Arm - Upper - Front - RH (1st Generation) (RWD) (Remove and Replace) - Updated procedure to latest validation.
  7. Door - Charge Port (Remove and Replace) - Updated China procedure to use Charge Port Voltage Check.
  8. Headliner - Glass Roof (Remove and Replace) - Added installation sequence and headliner shipping bag installation tip.
  9. Headliner - Panoramic Roof (Remove and Replace) - Added headliner shipping bag installation tip.
  10. Headliner (Remove and Replace) - Added installation sequence and headliner shipping bag installation tip.
  11. HV Battery (RWD/AWD) (Remove and Replace) - Added conspicuous discharge warning table. Updated pack configuration steps.
  12. Pin Carrier - Charge Port (Remove and Replace) - Updated procedure to use Charge Port Voltage Check, and not Vehicle Electrical Isolation Procedure.

Week Ending May 20, 2023

The following procedure(s) were updated:
  1. Clean and Lubricate Brake Calipers (Integrated Parking Brake) - Added Mobile Service notes to chock opposing wheels, service the front calipers, and then service the rear calipers.
  2. Clean and Lubricate Brake Calipers (Separate Parking Brake) - Added Mobile Service notes to chock opposing wheels, service the front calipers, and then service the rear calipers.
  3. Four Wheel Alignment Check and Adjust (Air Suspension) -
  4. Fuse - Pyrotechnic - HV Battery 1.0/1.5 (Remove and Replace) - Added fuse cover condition check with link to Toolbox article.
  5. Fuse - Pyrotechnic - HV Battery 2.0 (Remove and Replace) - Added fuse cavity and cover area condition check with link to Toolbox article.
  6. Latch - Hood (Remove and Replace) - Updated title.
  7. Navigation Micro SD Card - Media Control Unit (Remove and Replace) - Updated removal step 4 to state “destroy and discard the Micro SD card after removal”.

Week Ending May 13, 2023

The following new procedure(s) were added:
  1. Link - Panoramic Roof - Rear - LH (Remove and Replace)

Week Ending May 6, 2023

The following new procedure(s) were added:
  1. Pinch Sensor - Liftgate - LH (Remove and Replace)
The following procedure(s) were updated:
  1. Door - Charge Port (Remove and Replace) - Added note to 44012302 on calibrating non-motorized charge ports.
  2. Electrical Precautions - Updated HV battery storage temperature guidance.
  3. Finisher - Liftgate - Rear Window - Lower (Remove and Replace) - Added step to disconnect electrical harness from finisher.

Week Ending April 29, 2023

The following procedure(s) were updated:
  1. Maintenance Service and Intervals - Updated maintenance interval for tire rotation.

Week Ending April 22, 2023

The following new procedure(s) were added:
  1. 5003 - Charging Adapters - Created new section and moved Firmware Update - CHAdeMO Charging Adapter to there.
The following procedure(s) were updated:
  1. Air Suspension - Pressurize/Depressurize - Full System - Updated step sequence to close lever on hose adapter before setting EAS leveling to High through Toolbox 3 to prevent EAS Air Mass measurement routine from failing.
  2. Link - Fore - Lower - Front - LH (Remove and Replace) - Updated procedure according to the latest time studies. Air suspension depressurization/pressurization is no longer necessary.
  3. Links - Fore - Lower - Front - LH/RH (Remove and Replace) - Added step for FUCA ride height tool.
  4. Maintenance Service and Intervals - Updated maintenance interval for tire rotation.
  5. Toe Link Assembly - Rear - LH (Remove and Replace) - Updated 1st and 2nd Gen procedures to revised validations.

Week Ending April 15, 2023

The following procedure(s) were updated:
  1. Hub - Rear - LH (Remove and Replace) - Added steps to remove wheel, push in axle, and note to use a short socket to remove the hub mounting bolts.
  2. Link - Aft - Lower - LH (Remove and Replace) - Updated tool info.
  3. Pin Carrier - Charge Port (Remove and Replace)Fixed incorrect hyperlink to Vehicle Electrical Isolation Procedure.

Week Ending April 8, 2023

The following procedure(s) were updated:
  1. Coolant Rapid Mate - Vehicle Side (Remove & Replace) - Removed step for partial fill and added step for coolant air purge.
  2. Evaporator (1st Generation) (Remove and Replace) - Updated to latest validation.
  3. Fluids - Updated information on A/C oil type to be used.
  4. Fuse - Pyrotechnic - HV Battery 2.0 (Remove and Replace) - Updated with latest Toolbox 3 routine.
  5. Fuse - Pyrotechnic - HV Battery 1.0/1.5 (Remove and Replace) - Updated to latest validation and consistent with HV battery 2.0
  6. Radiator (Remove and Replace) - Updated to latest validation. Removed drain/fill steps.
  7. Tire - Front - LH (Road Force) (Balance) - Added Road Force Peak to Peak values.