Release Notes October-December 2022
Archived Release Notes:
- June-September 2022: Release Notes June-September 2022
- October-December 2022: Release Notes October-December 2022
- January-March 2023: Release Notes January-March 2023
- April-June 2023: Release Notes April-June 2023
- July-September 2023: Release Notes July-September 2023
- October-December 2023: Release Notes October-December 2023
- January-March 2024: Release Notes January-March 2024
- April-June 2024: Release Notes April-June 2024
- July-September 2024: Release Notes July-September 2024
Week Ending December 24, 2022
The following new procedure(s) were added:
The following procedure(s) were updated:
- Fuse - Pyrotechnic - HV Battery 2.0 (Remove and Replace) - Added vehicle electrical isolation check to procedure.
- Handle - Exterior Release - Door (Recalibrate) - Updated procedure with Toolbox information for all four doors.
- Links - Fore - Lower - Front - LH/RH (Remove and Replace) - Delete the Pressurize/Depressurize step.
- Toolbox 3 (Connect and Disconnect) - Added information on Toolbox Proxy.
Week Ending December 17, 2022
The following new procedure(s) were added:
The following procedure(s) were updated:
- Charge Port (China) (Remove and Retrofit) - Updated procedure and Toolbox information.
- Fuse - Pyrotechnic - HV Battery 2.0 (Remove and Replace) - All new procedure.
- Inline Fuse - HV Harness - HVJB to Front Drive Unit - 2nd Generation (Remove and Replace) - Updated procedure and Toolbox information.
- Inline Fuse to Busbar - HV Harness - HVJB to Front Drive Unit - 2nd Generation (Retrofit) - Updated procedure and Toolbox information.
Week Ending December 10, 2022
The following procedure(s) were updated:
- Seat Assembly - 1st Row - LH (Remove and Install) - Updated references from Driver to 1st row LH.
- Seat Assembly - 1st Row - LH (Remove and Replace) - Updated references from Driver to 1st row LH.
- Seat Assembly - 1st Row - RH (Remove and Replace) - Updated references from Front Passenger to 1st row RH.
Week Ending December 3, 2022
The following procedure(s) were updated:
- Sensor - HVAC - Light/Temperature/Humidity (Remove and Replace) - Updated to the latest validation.
Week Ending November 26, 2022
The following new procedure(s) were added:
Week Ending November 19, 2022
The following new procedure(s) were added:
Week Ending November 12, 2022
The following new procedure(s) were added:
The following procedure(s) were updated:
- Blower Motor - HVAC (Remove and Replace) - Updated to the latest validation.
- Charge Port - 3 Phase (Remove and Replace) - Added steps to unlock the Gateway.
- Cooling System - Drain and Refill - Replaced Toolbox 2 routines by Toolbox 3 routines.
- Drive Unit - Rear - Large (Remove and Replace) - Replaced Toolbox 2 routines by Toolbox 3 routines.
- Drive Unit - Rear - Small (Remove and Replace) - Replaced Toolbox 2 routines by Toolbox 3 routines.
- Handle - Exterior Release - Door - Front - LH - Generation 2.1 (Retrofit) - Replaced Toolbox 2 routines by Toolbox 3 routines.
- Module - Door Controller - LH (Remove and Replace) - Replaced Toolbox 2 routines by Toolbox 3 routines.
- Mount - Clevis - Front Drive Unit - LH (Remove and Replace) - Updated Model S procedure with steps to remove the HV battery
- Slave Charger - LH - 1st Generation (Remove and Replace) - Added Toolbox 3 routines.
- Slave Charger - LH - 2nd Generation (Remove and Replace) - Added Toolbox 3 routines.
- Calibration - Front Radar Sensor - Updated procedure to perform alignment check only drifting/pulling noticed during the test drive.
Week Ending November 5, 2022
The following procedure(s) were updated:
- Air Suspension - Pressurize/Depressurize - Full System - Updated topic with Toolbox 3 routines for Tesla Air Suspension.
Week Ending October 29, 2022
The following procedure(s) were updated:
- Charge Port - 3 Phase (Remove and Replace) - Replaced Toolbox 2 routines by Toolbox 3 routines.
- Door - Charge Port (Remove and Replace) - Replaced Toolbox 2 routines by Toolbox 3 routines.
- Four Wheel Alignment Check and Adjust (Air Suspension) - Added torque specification for cam bolt 1608802-00-C
- Four Wheel Alignment Check and Adjust (Coil Suspension) - Added torque specification for cam bolt 1608802-00-C
- Fuse - Pyrotechnic - HV Battery 2.0 (Remove and Replace) - Updated Toolbox 3 instructions.
- Halfshaft - Front Drive Unit - LH (2nd Generation) (Remove and Replace) - Updated part number for axle remover cable kit.
- Link - Aft - Lower - LH (Remove and Replace) - Added torque specification for cam bolt 1608802-00-C
- Rear Oil Seal - Differential to Halfshaft Assembly - Small Drive Unit - LH (Remove & Replace) - Removed Caution to replace snap ring.
- Subframe Assembly - Front (3rd Generation) (Remove and Install) - Added steps to disconnect the 4-way valve to battery pump 2 hose.
Week Ending October 15, 2022
The following procedure(s) were updated:
- Drive Unit - Rear - Large (Remove and Replace) - For vehicles outside of NA, added information on the Toolbox 3 immobilizer reset routine.
- Lights - Fog - Front (Adjust) - Fixed incorrect link to "Ride Height - Adjust" (Step 3).
Week Ending October 8, 2022
The following new procedure(s) were added:
The following procedure(s) were updated:
- Control Arm - Upper - Front - LH (Remove and Replace) - Added tool for installation procedure.
- Remove Stuck Deadfront - Charge Handle - Added first step to de-energize the Wall Connector or UMC, and step to put on PPE.