Release Notes June-September 2022

Week Ending October 1, 2022

The following new procedure(s) were added:
  1. Noise Absorber - Motor Bay - Front (Refresh) (Remove and Replace)
The following procedure(s) were updated:
  1. Drive Unit - Front (2nd Generation) (Remove and Install) - Change "Remove" to "Install" in the Mid Aero Shield link in the “Installation” section
  2. HV Battery (RWD/AWD) (Remove and Replace) - Edit Toolbox routines for GTW config
  3. Service Mode Plus - Locally connecting Toolbox 3 to the vehicle now automatically enables Service Mode Plus.

Week Ending September 24, 2022

The following new procedure(s) were added:
  1. Windshield Chip Repair
  2. Windshield Scratch Repair
The following procedure(s) were updated:
  1. GUID-EB1070FF-4028-4175-AE1C-F68A2DE0CE5B.html - Added step to refer to Alignment Requirement.
  2. Control Arm Assembly - Rear - Lower - LH (Remove and Replace) - Added step to refer to Alignment Requirement.
  3. Fuse - Pyrotechnic - HV Battery 2.0 (Remove and Replace) - Added contactor seize check section.
  4. Hub - Rear - LH (Remove and Replace) - Added step to refer to Alignment Requirement.
  5. HV Battery (RWD/AWD) (Remove and Install) - Change title to RWD/AWD and added correction code 16010201. Procedure completely updated to latest validation.Added steps to put on HV gloves when mating HV battery to vehicle.
  6. HV Battery (RWD/AWD) (Remove and Replace) - Change title to RWD/AWD and added correction code 16010202. Added steps to put on HV gloves when mating HV battery to vehicle.
  7. Integral Link - Rear - LH (Remove and Replace) - Added step to refer to Alignment Requirement.
  8. Knuckle - Suspension - Rear - LH (Remove and Replace) - Added step to refer to Alignment Requirement.
  9. Links - Front Suspension - Lower - Fore and Aft - LH/RH (Remove & Replace) - Added step to refer to Alignment Requirement.
  10. Link - Suspension - Rear - Upper - LH (Remove and Replace) - Added step to refer to Alignment Requirement.
  11. Rear Oil Seal - Differential to Halfshaft Assembly - Small Drive Unit - LH (Remove & Replace) - Updated install procedure.
  12. SIM Card - With SIM Extender (Remove and Replace) - Added a note to authenticate the new SIM card after installing for China only
  13. Spring and Damper Assembly - Rear - LH (Remove and Replace) - Added step to refer to Alignment Requirement.
  14. Stabilizer Bar - Rear (Remove and Replace) - Added step to refer to Alignment Requirement.
  15. Subframe Assembly - Rear (Remove and Install) - Added step to refer to Alignment Requirement.
  16. Subframe Assembly - Rear (Remove and Replace) - Added step to refer to Alignment Requirement.
  17. - Added step to refer to Alignment Requirement.

Week Ending September 17, 2022

The following procedure(s) were updated:
  1. Front suspension procedures that require a four wheel alignment check/adjust now refer to the Alignment Requirement procedure.

Week Ending September 10, 2022

The following procedure(s) were updated:
  1. GUID-FD9A5668-C6FB-457C-BC02-BF09E9219DB1.html - Modified procedure: no need to remove battery cage from vehicle.
  2. Center Support - Sun Visor - LH (Remove and Replace)- Change title from “driver” to “LH”
  3. Stabilizer Bar - Front (Dual Motor) (Remove and Replace) - Updated torque information.
  4. Sun Visor - LH (Remove and Replace) - Change title from “driver” to “LH” and correction code from 15050602 to 15051002

Week Ending September 3, 2022

The following new procedure(s) were added:
  1. Alignment Requirement - Suspension
  2. Isolation/Insulation Test
  3. Charge Port (Retrofit) (China)
The following procedure(s) were updated:
  1. - Added steps to check for and discharge high voltage on the Rapid Splitter.
  2. HV Battery (RWD/AWD) (Remove and Replace) - Added steps to check for and discharge high voltage on the Rapid Splitter.

Week Ending August 27, 2022

The following procedure(s) were updated:
  1. Drive Unit - Front (1st Generation) (Remove and Install) - Added drive unit alignment information.
  2. Pin Carrier - Charge Port (Remove and Replace) - Updated steps for Vehicle Isolation Procedure.
  3. Steering Rack (LHD Dual Motor) (2nd Generation) (Remove and Replace). - Update step to state “each LH bolt”
  4. Steering Rack (LHD RWD) (2nd Generation) (Remove and Replace) - Update step to state “each LH bolt”
  5. Steering Rack (RHD RWD) (2nd Generation) (Remove and Replace) - Update step to state “each LH bolt”

Week Ending August 20, 2022

The following new procedure(s) were added:
The following procedure(s) were updated:
  1. Drive Unit - Front (1st Generation) (Remove and Install) - Updated links to sub-procedures.
  2. HV Battery (RWD/AWD) (Remove and Replace) - Updated with unpacking and packing steps, and battery drain and refill.
  3. Roof - Glass (Remove and Replace) - Updated with steps for fixed glass roofs without urethane extrusions.
  4. Camera - Forward Facing (Pitch Verification) - Updated steps to set up a local connection, updated steps using Toolbox 3 to perform pre-calibration.

Week Ending August 13, 2022

The following procedure(s) were updated:
  1. HV Battery (RWD/AWD) (Remove and Replace) - Modified SoC percentage for shipping HV battery by air from 25% to 30%.
  2. Steering Rack (RHD Dual Motor) (3rd Generation) (Remove and Replace) - Updated torque figure for bolt that attaches the intermediate shaft to the steering rack from 49 Nm to 30 Nm.

Week Ending August 6, 2022

The following new procedure(s) were added:
  1. Fuse Box - Cabin - Front (Remove and Replace)
The following procedure(s) were updated:
  1. - Updated to latest GSD validation.
  2. Fluids - Added text to caution on the use of coolant not to use any additives.
  3. Drive Unit - Rear - Large (Remove and Install) - Add drive unit sling PN and clarify sling attachment step.

Week Ending July 30, 2022

The following procedure(s) were updated:
  1. - Updated and added references to caliper release.
  2. Bushing - Drive Unit - Rear - Large (Remove and Replace) - Add PN for the bushing tool.
  3. Cover - Back Rest - Driver Seat (Model 3 Seat) (Remove & Replace) - Updated link to airbag installation video.
  4. Foam - Back Rest - Driver Seat (Model 3 Seat) (Remove and Replace) - Updated link to airbag installation video.
  5. Module - Steering Column Control (Remove and Replace) - Updated the step to reflash the steering module using theToolbox Power Steering (EPAS) Control Panel to only apply the step when 1st Generation steering rack is installed.
  6. Steering Rack (LHD Dual Motor) (2nd Generation) (Remove and Replace) - Deleted the step to reflash the steering rack using the Toolbox Power Steering (EPAS) Control Panel since this only applies to 1st Generation steering rack.
  7. Steering Rack (LHD RWD) (2nd Generation) (Remove and Replace) - Deleted the step to reflash the steering rack using theToolbox Power Steering (EPAS) Control Panel since this only applies to 1st Generation steering rack.
  8. Steering Rack (RHD Dual Motor) (2nd Generation) (Remove and Replace) - Deleted the step to reflash the steering rack using theToolbox Power Steering (EPAS) Control Panel since this only applies to 1st Generation steering rack.
  9. Steering Rack (RHD RWD) (2nd Generation) (Remove and Replace) - Deleted the step to reflash the steering rack using theToolbox Power Steering (EPAS) Control Panel since this only applies to 1st Generation steering rack.
  10. - Delete the step to remove MCU.

Week Ending July 23, 2022

The following procedure(s) were updated:
  1. Bleed or Flush Procedure - System (Remove and Replace) - Added step to perform test drive after replacement.
  2. Firmware Redeploy - Added steps to attach 12V support charger.
  3. Trim - C-Pillar - Upper - LH (Remove and Replace) - Added step to remove LH rear C-pillar trim and installation sequence.
  4. Oil Pump - Front Drive Unit (2nd Generation) (Remove and Replace) - Added step to update firmware at installation.
  5. Software Reinstall - Added steps to attach 12V support charger.

Week Ending July 16, 2022

The following new procedure(s) were added:
  1. Bracket - Radar - Front (DAS 1/2) (Remove and Replace)
  2. Bracket - Radar - Front (DAS 2.5) (Remove and Replace)

Week Ending July 9, 2022

The following new procedure(s) were added:
  1. Charger Port (China) (Remove and Retrofit)
  2. Sensor - Brake Reservoir Fluid Level (Remove and Replace)
The following procedure(s) were updated:
  1. Four Wheel Alignment Check (Air Suspension) - Remove bad link
  2. Four Wheel Alignment Check (Coil Suspension) - Remove bad link
  3. Micro SD Card - Media Control Unit (Remove and Replace) - Added Toolbox articles for additional information.
  4. SD Card - Media Control Unit (Remove and Replace) - Added Toolbox articles for additional information.

Week Ending July 2, 2022

The following new procedure(s) were added:
  1. Vehicle Sanitation - Tunap (Basic Package) (EMEA)
  2. Vehicle Sanitation - Tunap (Complete Package) (EMEA)
The following procedure(s) were updated:
  1. Four Wheel Alignment Check – Simplified topic.
  2. Four Wheel Alignment Check and Adjust – Simplified topic.
  3. Drive Unit - Front (1st Generation) (Remove and Replace) - Restored broken link in installation procedure.
  4. Knuckle - Suspension - Front - LH (Remove and Replace) - Lower control arm nuts are to be replaced and installed with lock washers.

Week Ending June 25, 2022

The following procedure(s) were updated:
  1. Link - Fore - Lower - Front - LH (Remove and Replace) - Added installation sequence, and explanation of fastener orientation.
  2. Link - Fore - Lower - Front - LHRH (Remove and Replace) - Optimized text, added installation sequence, and explanation of fastener orientation.
  3. Locking Devices - Added Fastener Symmetry section to describe orientation of nuts and washers.
  4. Receiver Dryer and Desiccant (Remove and Replace) - Revised installation steps.
  5. Harness - Body - LH (Remove and Replace) - Updated correction code.
  6. Subframe Assembly - Rear (Remove and Install) - Organized procedure into separate sections for large RDU and small RDU.
  7. Coax Cable - Side Repeater - Front - LH (Replace) - Updated images to clarify difference between LH and RH
  8. Coax Cable - Side Repeater - Front - RH (Replace) - Updated images to clarify difference between LH and RH

Week Ending June 18, 2022

The following procedure(s) were updated:
  1. Receiver Dryer and Desiccant (Remove and Replace) - Moved up the warnings.
  2. Air Suspension - Pressurize/Depressurize - Full System - Add closing routine for EAS (Conti) air suspension systems.

Week Ending June 11, 2022

The following new procedure(s) were added:
  1. Rapid Mate - Low Voltage - HV Battery 2.0 (Remove and Replace)
The following procedure(s) were updated:
  1. Cross Car Beam (Remove and Replace) - Added note for correct pin guide placement.
  2. Harness - Media Control Unit (Retrofit) - Added note for yellow wire harness tape.
  3. Sensor - Occupant Classification - Front Passenger’s Seat - Calibration - Procedure rewritten to use Toolbox 3.
  4. Subframe Assembly - Rear (Remove and Install) - Procedure rewritten to accommodate the removal of the alignment check.

Week Ending June 04 , 2022

The following new procedure(s) were added:
The following procedure(s) were updated:
  1. Vehicle Identification Number (VIN) - Clarified VIN locations for pre-refresh and refresh MS vehicles.
  2. AC Refrigerant Leak Detection - Added note to replace desiccant bag when a leak has been detected.
  3. AC Refrigerant Recovery and Recharge (Remove and Replace) - Added step to release vacuum from system.
  4. Clean and Lubricate Brake Calipers (Integrated Parking Brake) - Updated with information regarding correction code usage.
  5. Clean and Lubricate Brake Calipers (Separate Parking Brake) - Updated with information regarding correction code usage.

Week Ending May 28, 2022

The following new procedure(s) were added:
  1. Applique - Fascia - Rear (Remove and Replace)
  2. Harness - Front Drive Unit (Remove and Replace)
The following procedure(s) were updated:
  1. Instrument Cluster (Remove and Replace) - Procedure updated to improve install time.
  2. Fuse - HV Battery (2.0) (Remove and Replace) - Tool information updated.
  3. Charger (China) (Remove and Replace) - Tool information updated.