Release Notes October-December 2023
Archived Release Notes:
- June-September 2022: Release Notes June-September 2022
- October-December 2022: Release Notes October-December 2022
- January-March 2023: Release Notes January-March 2023
- April-June 2023: Release Notes April-June 2023
- July-September 2023: Release Notes July-September 2023
- October-December 2023: Release Notes October-December 2023
- January-March 2024: Release Notes January-March 2024
- April-June 2024: Release Notes April-June 2024
- July-September 2024: Release Notes July-September 2024
Week Ending December 30, 2023
The following new procedure(s) were added:
The following procedure(s) were updated:
- Module - Autopilot - ECU - 2nd and 3rd Generation (Remove and Replace) - Added note to firmware step.
Week Ending December 23, 2023
The following procedure(s) were updated:
- Halfshaft - Front Drive Unit - LH (2nd Generation) (Remove and Replace) - Added step to perform test drive to break in new halfshaft.
- Panel - Cowl Screen (Remove and Replace) - Added instruction for vehicles equipped with pedestrian protection actuators.
- Ski - Side Rail - HV Battery - LH (Remove and Replace) - Updated install procedure.
Week Ending December 16, 2023
The following new procedure(s) were added:
The following procedure(s) were updated:
- Door Glass - LH - Front - Adjust - Updated the original nonadjustable correction code to the new adjustable one.
- Halfshaft - Front Drive Unit - RH (2nd Generation) (Remove and Replace) - Added step to perform test drive to break in new halfshaft(s).
- Lights - Fog - Front (Adjust) - Added photo for fog light adjustment.
- Module - Air Suspension - ECU (Tesla) (LHD) (Remove and Replace) - Condensed installation procedure.
- Module - Air Suspension - ECU (Tesla) (RHD) (Remove and Replace) - Condensed installation procedure.
- Ride Height - Adjust - Corrected Toolbox routines for Tesla air suspension.
- Seal - Axle - Front Drive Unit - LH (1st Generation) (Remove and Replace) - Removed alignment check.
Week Ending December 9, 2023
Week Ending December 2, 2023
The following new procedure(s) were added:
The following procedure(s) were updated:
- Fuse - Pyrotechnic - HV Battery 1.0/1.5 (Remove and Replace) - Updated pyro fuse selection steps.
- Fuse - Pyrotechnic - HV Battery 2.0 (Remove and Replace) - Updated pyro fuse selection steps.
- Premium Console Sub-assembly (Remove and Replace) - Added steps to remove the wireless charger assembly from the center console sub-assembly.
- Seal - HV Rapid Mate (Vehicle Side) (Remove and Replace) - Added image for installation.
- Seat Assembly - 1st Row - LH (Remove and Replace) - Added step to test the seat ventilation functionality before changing configuration.
Week Ending November 25, 2023
The following new procedure(s) were added:
The following procedure(s) were updated:
- Door Assembly - Front - LH (Remove and Install) - Added rework instructions to enable fitting of early type pressure sensor to new type door.
Week Ending November 18, 2023
The following new procedure(s) were added:
The following procedure(s) were updated:
- Handle - Exterior Release - Door - Rear - LH - Generation 2.1 (Retrofit) - Added correct image of the LED harness cavity.
- HV Battery (RWD/AWD) (Remove and Replace) - Replaced steps with link to 12V Disconnect procedure.
- LED - Door - Exterior Handle - Rear - LH (Remove and Replace) - Added images that show LED harness routing on Gen 2 and newer door handle assemblies.
- Toe Link Assembly - Rear - LH (Remove and Replace) - Deleted/added some steps and corrected some wrong images.
Week Ending November 11, 2023
The following procedure(s) were updated:
- Sensor - Ultrasonic - Rear Door - LH (Remove and Replace) - Updated ultrasonic sensor temperature for installation.
- Seal - Axle - Front Drive Unit - LH (2nd Generation) (Remove and Replace) - Added information about the FDU Oil Seal Installation Auxiliary Rod (2004567-00-A).
- Seal - Axle - Front Drive Unit - RH (2nd Generation) (Remove and Replace) - Added information about the FDU Oil Seal Installation Auxiliary Rod (2004567-00-A).
Week Ending November 4, 2023
The following procedure(s) were updated:
- Links - Aft - Lower - LH/RH (Remove and Replace) - Provided part number for the Oscillating Multi-Tool.
Week Ending October 28, 2023
The following procedure(s) were updated:
- Handle - Exterior Release - Door (Recalibrate) - Updated instructions for calibration using UI.
- Handle - Exterior Release - Door - Front - LH - Generation 3.0 (Remove and Replace) - Added reference to calibration procedure.
- Handle - Exterior Release - Door - Front - LH - Generation 3.0 (Retrofit) - Rearranged installation steps and added extra note.
- Handle - Exterior Release - Door - Rear - LH - Generation 2.1 (Retrofit) - Rearranged installation steps.
- Handle - Exterior Release - Door - Rear - LH - Generation 3.0 (Retrofit) - Rearranged installation steps and added extra note.
- Liftgate Assembly (Remove and Replace) - All replacement liftgates must be reworked so that they can be installed on classic Model S. This procedure has been updated to include rework instructions.
- Module - Door Handle Controller - Front - LH - Generation 3.0 (Remove and Replace) - Rearranged installation steps.
- TPMS Sensor - ID Learn Procedure - Continental - Updated Toolbox routine.
Week Ending October 21, 2023
The following procedure(s) were updated:
- Battery - Auxiliary - 12V (Remove and Replace) - Added battery type configuration using the touchscreen.
Week Ending October 14, 2023
The following procedure(s) were updated:
- Disconnect 12V Power - Updated vehicle isolation note.
Week Ending October 7, 2023
The following procedure(s) were updated:
- Calibration - Front Radar Sensor - Added increase/decrease direction for clockwise/counterclockwise values in Alignment Adjustment table.
- Added alternative special tool for the following procedures: