Week Ending December 24, 2022

The following new procedure(s) were added:

1. Fuse - A/C Compressor - HV Battery (Remove and Replace)
2. Fuse - Power Conversion System - HV Battery (Remove and Replace)

Week Ending December 17, 2022

The following new procedure(s) were added:

1. Cover - Inverter - Drive Unit - Front (Remove and Replace)

The following procedure(s) were updated:

1. Contactor - Fast Charge - HV Battery (Remove and Replace) - Updated pyro fuse, air leak test, and HV battery installation sequence.
2. Contactor - Negative - HV Battery (Remove and Replace) - Updated pyro fuse, air leak test, and HV battery installation sequence.
3. Contactor - Positive - HV Battery (Remove and Replace) - Updated pyro fuse, air leak test, and HV battery installation sequence.
4. Controller - High Voltage (Remove and Replace) - Updated pyro fuse, air leak test, and HV battery installation sequence.
5. Cover - Front Access - HV Battery (Remove and Install) - Updated pyro fuse, air leak test, and HV battery installation sequence.
6. Cover - Rear Access - HV Battery (Remove and Replace) - Updated pyro fuse, air leak test, and HV battery installation sequence.
7. Harness - Pyrotechnic - HV Battery (Remove and Replace) - Updated pyro fuse, air leak test, and HV battery installation sequence.
8. Link - Fore - Lower - Rear - LH (Remove and Replace) - Updated torque information.
9. Power Conversion System (Remove and Replace) - Updated pyro fuse, air leak test, and HV battery installation sequence.
10. Shunt - HV Battery (Remove and Replace) - Updated pyro fuse, air leak test, and HV battery installation sequence.

Week Ending December 10, 2022

The following new procedure(s) were added:

1. Switch - Lid - Center Console (Remove and Replace)

The following procedure(s) were updated:

1. Seat Assembly - 1st Row - LH (Remove and Replace) - Updated references from Driver to 1st row LH.

Week Ending November 26, 2022

The following procedure(s) were updated:

1. Replacement Keys - Program (No Keys Present) - Updated steps for pairing key fob(s).
2. Inverter - Front Drive Unit (Remove and Replace) - Added overview videos.

Week Ending November 19, 2022

The following new procedure(s) were added:

1. Cooling System (Check and Fill) - This procedure decribes coolant top off without system air purge.
2. Pad - Lifting - Each (Remove and Replace)

The following procedure(s) were updated:

1. Cooling System (Partial Refill and Bleed) - Updated procedure title. This procedure describes coolant top off and system air purge.
2. Firmware Update - Updated steps per latest prompts on the vehicle touchscreen.

Week Ending November 12, 2022

The following procedure(s) were updated:

1. - Updated procedure to perform alignment check only drifting/pulling noticed during the test drive.
2. Sensor - Radar - Front (Remove and Replace) - Updated procedure to perform alignment check only drifting/pulling noticed during the test drive.
3. Windshield (Remove and Install) - Added a Caution and image to show two locations to be extra cautious when cutting urethane.

Week Ending November 5, 2022

The following procedure(s) were updated:

1. Carrier - Connector - Front - HV Battery (Remove and Replace) - Added/updated cross references to pyrotechnic battery disconnect procedure with voltage check.
2. Contactor - Fast Charge - HV Battery (Remove and Replace) - Added/updated cross references to pyrotechnic battery disconnect procedure with voltage check.
3. Contactor - Negative - HV Battery (Remove and Replace) - Added/updated cross references to pyrotechnic battery disconnect procedure with voltage check.
4. Contactor - Positive - HV Battery (Remove and Replace) - Added/updated cross references to pyrotechnic battery disconnect procedure with voltage check.
5. Controller - High Voltage (Remove and Replace) - Added/updated cross references to pyrotechnic battery disconnect procedure with voltage check.
6. Cover - Front Access - HV Battery (Remove and Install) - Added/updated cross references to pyrotechnic battery disconnect procedure with voltage check.
7. Cover - Rear Access - HV Battery (Remove and Replace) - Added/updated cross references to pyrotechnic battery disconnect procedure with voltage check.
8. Harness - High Voltage Controller - HV Battery (Remove and Replace) - Added/updated cross references to pyrotechnic battery disconnect procedure with voltage check.
9. Harness - LV - Front - HV Battery (Remove and Replace) - Added/updated cross references to pyrotechnic battery disconnect procedure with voltage check.
10. Harness - Pyrotechnic - HV Battery (Remove and Replace) - Added/updated cross references to pyrotechnic battery disconnect procedure with voltage check.
11. HV Harness - Heat Pump - HV Battery (Remove and Replace) - Added/updated cross references to pyrotechnic battery disconnect procedure with voltage check.
12. Power Conversion System (Remove and Replace) - Added/updated cross references to pyrotechnic battery disconnect procedure with voltage check.
13. Shunt - HV Battery (Remove and Replace) - Added/updated cross references to pyrotechnic battery disconnect procedure with voltage check.

Week Ending October 29, 2022

The following new procedure(s) were added:

1. Liftgate (Remove and Replace)

The following procedure(s) were updated:

1. Four Wheel Alignment Check and Adjust - Update torque for the LH lower aft link to front subframe to 127 Nm

Week Ending October 22, 2022

The following new procedure(s) were added:

1. Actuator - Pedestrian Protection - LH (EMEA) (Remove and Replace)
2. Busbars - Charge Port to HV Battery (EMEA) (Remove and Replace)
3. Charge Port (EMEA) (Remove and Replace)
5. Door Panel - Charge Port (Remove and Replace)
6. Foam - Back Rest - Driver Seat (With Inboard Airbag) (Remove and Replace)
7. Harness - Body - LH (EMEA) (Remove and Replace)
8. Harness - Main Front (EMEA) (Remove and Replace)
9. Safety Cap - Busbar - Charge Port to HV Battery (EMEA) (Remove and Replace)
10. Sensor - Pressure Tube (Pedestrian Protection) (EMEA) (Remove and Replace)
11. Siren - Battery Backed (EMEA) (Remove and Replace)

The following procedure(s) were updated:

1. Pyrotechnic Battery Disconnect (Remove and Replace) - Added steps to balance the voltage across the pyrotechnic battery disconnect mount points.

Week Ending October 15, 2022

The following procedure(s) were updated:

1. Charge Port (Remove and Replace) - Added torque specification

Week Ending October 8, 2022

The following new procedure(s) were added:

1. Controller - High Voltage (Backup and Restore)

The following procedure(s) were updated:

1. Controller - High Voltage (Remove and Replace) - Added links to backup and restore procedures.
2. Remove Stuck Deadfront - Charge Handle - Added first step to de-energize the Wall Connector or UMC, and step to put on PPE.