Release Notes April-June 2023
Archived Release
Notes:
- June-September 2022: Release Notes June-September 2022
- October-December 2022: Release Notes October-December 2022
- January-March 2023: Release Notes January-March 2023
- April-June 2023: Release Notes April-June 2023
- July-September 2023: Release Notes July-September 2023
- October-December 2023: Release Notes October-December 2023
- January-March 2024: Release Notes January-March 2024
- April-June 2024: Release Notes April-June 2024
- July-September 2024: Release Notes July-September 2024
Week Ending July 1, 2023
The following procedure(s) were updated:
- A/C Refrigerant (Recovery and Recharge) -
- Brake Bleeder Machine (Flush) - Clarified steps and noted that this procedure is for the Bremsen brake bleeder machine.
- Insulator - Dash (HW3) (Remove and Replace) - Revised procedure.
- Mechanism - Pivot - Touchscreen (Remove and Replace) - Added option links to remove/install HW3 touchscreen and HW4 touchscreen.
- Steering Yoke/Wheel (Remove and Replace) - Updated firmware reinstall step; it is to be performed whenever the steering wheel/yoke is replaced.
Week Ending June 24, 2023
The following new procedure(s) were added:
The following procedure(s) were updated:
- A/C Line - Supermanifold to HVAC (Remove and Replace) - Added link to vehicle electrical isolation procedure.
- Acoustic Blanket - Compressor (Remove and Replace) -
- Applique - B-Pillar - LH (Remove and Replace) - Switch the steps so that DAS Reset occurs directly before the Camera Connection Test.
- Bracket - Compressor (Remove and Replace) - Added link to vehicle electrical isolation procedure.
- Camera - Forward Facing (Pitch Verification) - Updated images and added notes to check measurement for each setup.
- Camera - Rear Facing (HW4) (Remove and Replace) - Switch the steps so that DAS Reset occurs directly before the Camera Connection Test.
- Controller - Driver Seat (Remove and Replace) - Updated procedure not to remove seat from vehicle, added seat assignment routine and modified seat calibration routine.
- Gearbox Fluid - Rear Drive Unit (Plaid) (Drain and Refill) - Added PN for fill port adapter.
- Heat Exchanger - Rear Drive Unit - LH (Plaid) (Remove and Replace) - Added link to vehicle electrical isolation procedure.
- Module - 2nd Row Seat Controller - LH (5 Seat) (Remove and Replace) - Seat controller module assignment routine added, firmware reinstall step modified.
- Subframe Assembly - Rear (Remove and Install) - Updated suspension ride height check.
- Vehicle HV Disablement Procedure - Updated photos to show CAT III probes being used and corrected photo for HV harness connection.
- Updated steps for seat belt linkage release/install in procedures that require seat removal and related trim removal.
Week Ending June 17, 2023
The following procedure(s) were updated:
- Four Wheel Alignment Check - Added cycle suspension ride height to High and then back to Medium when vehicle is on alignment rack with the pins pulled from the turn plates.
- Four Wheel Alignment Check and Adjust - Added cycle suspension ride height to High and then back to Medium when vehicle is on alignment rack with the pins pulled from the turn plates.
- Inverter - Front Drive Unit (Remove and Replace) - Replaced Toolbox 3 routines with Touchscreen UI steps.
- Seat Assembly - 1st Row - LH (Remove and Replace) - Added change config steps for replacing non-FSAB seat with FSAB-equipped seat.
Week Ending June 10, 2023
The following procedure(s) were updated:
- Camera - Forward Facing (Pitch Verification)- Added specifications for HW4 vehicles and general image and step updates.
- Contactor - Fast Charge - HV Battery (Remove and Replace) - Added steps and notes to accommodate mica insulators and tape.
- Contactor - Positive - HV Battery (Remove and Replace) - Added steps and notes to accommodate mica insulators and tape.
- Cover - Rear Access - HV Battery (Remove and Replace) - Added steps to remove and install the mica insulator panel.
- Module - Air Suspension - ECU (Tesla) (LHD) (Remove and Replace) - Added information for HW4 vehicles.
- Module - Battery Controller (Remove and Replace) - Updated software reinstall steps.
- Wheel Alignment - Added specifications for vehicles equipped with the Track Package.
Week Ending May 27, 2023
The following procedure(s) were updated:
- Door Glass - Front - LH (Adjust) - Added cleaning instructions to prevent glass damage.
- Door Glass - Front - LH (Remove and Replace) - Added cleaning instructions to prevent glass damage.
- Door Glass - Rear - LH (Adjust) - Added cleaning instructions to prevent glass damage.
- Door Glass - Rear - LH (Remove and Replace) - Added cleaning instructions to prevent glass damage.
- Headliner (Remove and Replace) - Added headliner shipping bag installation tip.
- HV Battery (AWD) (Remove and Install) - Reorganized Removal first steps.
- HV Battery (AWD) (Remove and Replace) - Added conspicuous discharge warning table.
- HV Battery (AWD) (Remove and Replace) - Reorganized Removal first steps.
- Platter Enclosure Coolant (Drain) - Added note that coolant cart pressure regulator is fixed at 20 psi.
Week Ending May 20, 2023
The following new procedure(s) were added:
Week Ending May 13, 2023
The following procedure(s) were updated:
- Back Rest - Driver (Remove and Replace) - Reorganized the procedure.
- Panel - Footrest - Front Passenger (LHD) (Remove and Replace) - Fixed errors.
- Spoiler - Rear (Remove and Replace) - Added special tool.
Week Ending May 6, 2023
The following new procedure(s) were added:
The following procedure(s) were updated:
- Drive Unit - Rear (Plaid) (Remove and Replace) - Updated to latest validation.
- Electrical Precautions - Updated HV battery storage temperature guidance.
- Skidplate - Front (Remove and Replace) - Updated photos and added steps for additional bolts.
- Subframe Assembly - Rear (Plaid) (Remove and Install) - Added steps to conditionally remove rotor and release wheel arch liner.
- Vehicle HV Disablement Procedure - Updated current measurement step sequence and consistency.
Week Ending April 29, 2023
The following procedure(s) were updated:
- A/C Refrigerant (Recovery and Recharge) -
- Cover - Inverter - Drive Unit - Front (Remove and Replace) - Updated "screw clip" to "brush clip".
- Instrument Cluster (Remove and Replace) - Reorganized the procedure..
- Maintenance Service and Intervals - Updated maintenance interval for tire rotation.
- Wheel - Front - LH (Remove and Replace) - Reorganized the procedure..
Week Ending April 22, 2023
The following new procedure(s) were added:
- 5003 - Charging Adapters - Created new section and moved Firmware Update - CHAdeMO Charging Adapter to there.
- SIM Card - Car Computer (Info-Ryzen) (Retrofit)
The following procedure(s) were updated:
- Module - Body Controller - LH (Remove and Replace) - Streamlined the procedure.
- Module - Body Controller - RH (Remove and Replace) - Cleaned up.
- Side Repeater Camera - Front - LH (HW4) (Remove and Replace) - Added HW4 camera connection test steps.
- Sub Assembly - Instrument Panel (Remove and Install) - Added note for additional ground strap PN for non-HW4 vehicles.
Week Ending April 15, 2023
The following new procedure(s) were added:
The following procedure(s) were updated:
- Alignment Requirement - Suspension - Updated alignment requirement tables.
- Cover - Front Access - HV Battery (Remove and Install) - Added conditional steps for when there is a doubler around the front access cover.
- Inverter - LH - Rear Drive Unit (Plaid) (Remove and Replace) - Reordered steps around the before replacement dashboard.
- Module - Battery Controller (Remove and Replace) - Cleaned up.
- Panel - Door Trim - Front - LH (Remove and Replace) - Added links to armrest service cover and door trim reflector.
- Supermanifold (Remove and Replace) - Revised procedure.
Week Ending April 8, 2023
The following new procedure(s) were added:
The following procedure(s) were updated:
- Aero Lens - Instrument Panel (Remove and Replace) - Added note on reworked datums/mounting tabs.
- Halfshaft - Front Drive Unit - LH (Remove and Replace) - Added test drive at the end of procedure as per latest GSD validation.
- Touchscreen (HW3) (Remove and Replace) - Added steps for the electrical connectors for the tilt motors (if equipped).
- Underhood Storage Unit (Remove and Install) - Added check for proper routing of and possible damage to HVIL harness branch.
- Underhood Storage Unit (Remove and Replace) - Added check for proper routing of and possible damage to HVIL harness branch.